Cisco 7330 User manual
QUICK START GUIDE
Cisco Universal Small Cell 7330
2
Revised: November, 2013, 78-21441-03
Table of Contents
1About Your Small Cell
2Before You Begin
3Safety Instructions
4Connect Your Small Cell
5Mount Your Small Cell
Mounting on a Wall or Hard Ceiling
Mounting on a Suspended Ceiling
Mounting on a Suspended Ceiling Using an Existing
Bracket
Mounting in a Plenum Space
6Verify that Your Small Cell is Operating Correctly
7Declarations of Conformity and Regulatory Information
8Specifications
9Obtaining Documentation and Submitting a Service
Request
3
1 About Your Small Cell
The Cisco Universal Small Cell (USC) 7330 is an indoor small
cell that provides Wideband Code Division Multiple Access
(WCDMA) coverage and capacity to public areas where macro
networks are not cost-effective. The USC 7330 supports up to
16 active third-generation (3G) users and supports Band 2/5 for
the American market and Band 1 for the rest of the world.
Package Contents
Your Cisco USC 7330 small cell is shipped with the following:
•Power supply unit—European Union (EU) compatible type
plug for Band 1 and US compatible plug for Band 2/5.
Other plug types must be ordered separately.
•Suspended ceiling mount bracket—to mount the small cell
on a ceiling.
•Rail mounting accessory pack, including screws.
•Ethernet cable.
•This Quick Start Guide.
4
Figure 1 Cisco USC 7330 Top View
1Power LED
2Ethernet connection LED
3Status LED
4External antenna port
361429
2
3
1
4
5
2 Before You Begin
Consider where you want to install your new small cell. The
ideal location is:
•somewhere central, away from windows—this will allow
your small cell to provide the best possible coverage.
•at least one 30 cm (1 foot) from other wireless broadcasting
devices to avoid possible interference.
•where you can connect to your broadband router or cable
modem.
Decide whether you will mount your small cell on a wall or
ceiling, or whether you will place it on a desktop or other flat
surface.
6
3 Safety Instructions
Translated versions of the following safety warnings are
provided in Cisco USC 7330 Regulatory Compliance and
Safety Information, located on Cisco.com.
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a
situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards
involved with electrical circuitry and be familiar
with standard practices for preventing accidents.
Use the statement number provided at the end of
each warning to locate its translation in the
translated safety warnings that accompanied this
device.
Statement 1071
SAVE THESE INSTRUCTIONS
Warning
Read the installation instructions before you
connect the system to its power source.
Statement
1004
7
Warning
Installation of the equipment must comply with
local and national electrical codes.
Statement 1074
Warning
This product relies on the building’s installation
for short-circuit (overcurrent) protection. Ensure
that the protective device is rated not greater than:
20A.
Statement 1005
Warning
Do not operate the unit near unshielded blasting
caps or in an explosive environment unless the
device has been modified to be especially
qualified for such use.
Statement 364
Warning
In order to comply with FCC radio frequency (RF)
exposure limits, antennas should be located at a
minimum of 7.9 inches (20 cm) or more from the
body of all persons.
Statement 332
8
Caution The fasteners you use to mount an access point on
a ceiling must be capable of maintaining a
minimum pullout force of 20 lbs (9 kg) and must
use all indented holes on the mounting bracket.
Caution This product and all interconnected equipment
must be installed indoors within the same building,
including the associated LAN connections as
defined by Environment A of the IEEE 802.af
Standard.
Note Your small cell is suitable for use in environmental air
space in accordance with section 300.22.C of the
National Electrical Code and sections 2-128,
12-010(3), and 12-100 of the Canadian Electrical
Code, Part 1, C22.1. You should not install the power
supply or power injector in air handling spaces.
Note Use only with listed ITE equipment.
9
4 Connect Your Small Cell
Figure 2 Cisco USC 7330 Connections
110/100 Base-T Ethernet port supporting PoE+
2Power port
3GPS port (available on Band 2/5 only)
6
361430
1
2
3
4
5
10
Step 1 Connect one end of the network cable to the small cell
Ethernet port and the other end to your broadband
router or cable modem.
Step 2 Connect the power adaptor to the power port and then
switch on at the mains.
Step 3 (Optional) If you have a Band 2/5 small cell, you can
connect a GPS antenna to the GPS port.
Step 4 (Optional) You can connect an external antenna. For
the USC7330-T1-K9, connect an external antenna for
the Sniff bands (Bands 3 and 8) to connector 5 and
connect the external antenna for Band 1 to connector 6
(Figure 2). For the USC7330-T2-K9, connect an
external antenna for Band 5 to connector 5 and connect
the external antenna for Band 2 to connector 6
(Figure 2).
4Reset button
52G external antenna port for the Band 1 small cell
(USC7330-T1-K9) or UMTS Band V external antenna port
for the Band 2/5 small cell (USC7330-T2-K9)
63G external antenna port for the Band 1 small cell
(USC7330-T1-K9) or UMTS Band II external antenna port
for the Band 2/5 small cell (USC7330-T2-K9)
Table of contents
Other Cisco Wireless Access Point manuals
Cisco
Cisco 800 Series User manual
Cisco
Cisco AIR-AP1020 - 1000 Series Lightweight Access... User manual
Cisco
Cisco Linksys WAP54GX User manual
Cisco
Cisco AIR-LAP1310G User manual
Cisco
Cisco WAP121 Instruction Manual
Cisco
Cisco ISR User manual
Cisco
Cisco WAP300N User manual
Cisco
Cisco Aironet 1572EC Quick reference guide
Cisco
Cisco MERAKI MR46E-HW Manual
Cisco
Cisco Aironet OfficeExtend AIR-OEAP602I-E-K9 User manual
Cisco
Cisco Aironet 1100 Series Operator's manual
Cisco
Cisco WAP571 User manual
Cisco
Cisco Aironet 1400 Series Manual
Cisco
Cisco Catalyst Wireless 9163E User manual
Cisco
Cisco Aironet 1570 Series User manual
Cisco
Cisco Aironet 1520 Series User manual
Cisco
Cisco Meraki MR12 User manual
Cisco
Cisco Catalyst Wireless 9164I Series User manual
Cisco
Cisco WUMC710 User manual
Cisco
Cisco Meraki GR60 User manual
