Cisco NCS 4216 Instruction Manual
Installing the Cisco NCS 4216
This chapter describes how to install the Cisco NCS 4216.
•Prerequisites, on page 1
•Installing the Router in a Rack, on page 1
•Installing the Chassis Ground Connection, on page 17
•Installing the Fan Tray, on page 19
•RSP Installation, on page 26
•Interface Module Installation, on page 29
•Installing the Power Supply, on page 33
•Installing the AC power Supply, on page 39
•Connecting the Cisco NCS 4216 Router to the Network, on page 42
Prerequisites
Before installing the Cisco NCS 4216, it is important to prepare for the installation by:
• Preparing the site (site planning) and reviewing the installation plans or method of procedures (MOP)
• Unpacking and inspecting the Cisco NCS 4216
• Gathering the tools and test equipment required to properly install the Cisco NCS 4216
For more instructions on how to prepare for the installation of the Cisco NCS 4216, see the Preparing for
Installation section.
Installing the Router in a Rack
The sections describe how to install the Cisco NCS 4216 in a rack.
The Cisco NCS 4216 Door is not displayed in the figures below. It is only displayed in the Installing the Cisco
NCS 4216 Door figure.
Note
Installing the Cisco NCS 4216
1
Installing the Chassis Brackets
The chassis is shipped with mounting brackets that can be installed on the front or rear of the chassis. To
install the brackets on the front of the chassis, perform these steps:
Procedure
Step 1 Remove the rack-mount brackets from the accessory kit and position them beside the router chassis.
Figure 1: Attaching Mounting Brackets for a 23-inch Rack
Step 2 Position one of the brackets against the chassis side, and align the screw holes.
Step 3 Secure the bracket to the chassis with the screws removed when performing Step 1. The recommended
maximum torque is 28 in.-lb (3.16 N-m).
The A907-FAN-E fan tray with filter (A907-FAN-F) cannot be mounted using the mounting screws that are
supported for fan tray. This is not an issue with the FAN tray filter blank panel (A907-FAN-F-B). We
recommend that you use the short screws provided in the following rack mount kits to avoid interference of
the air filter during rack mounting and while replacing the fan tray with the fan tray filter (A907-FAN-E):
• 23" rack mount kit (A907-RCKMT-23IN)
What to do next
Repeat Step 2 and Step 3 for the other bracket.
Installing the Cisco NCS 4216
2
Installing the Cisco NCS 4216
Installing the Chassis Brackets
Installing Plenum Assembly and Chassis in the Rack
Following steps help you to install the plenum assembly irrespective of the chassis and rack size.
The below illustrations are for representation purpose only. The size displayed in the images may vary
depending upon your chassis type and rack size but the steps remain the same. Ensure to select the 21 or 23
inches adapter for your plenum based on your rack size.
Note
Procedure
Step 1 Position the adapter to the plenum base and secure using a maximum torque of 11.5 in.-lb (1.3 N-m). See
figure below.
Figure 2: Adapter to Plenum
Plenum2Plenum adapter deflector1
-Securing the Plenum to the base3
Step 2 Position the air deflector inside the plenum and secure using a maximum torque of 11.5 in.-lb (1.3 N-m). See
figure below.
Installing the Cisco NCS 4216
3
Installing the Cisco NCS 4216
Installing Plenum Assembly and Chassis in the Rack
Figure 3: Deflector in Plenum
Plenum2Air deflector1
Step 3 Secure the plenum deflector with a recommended torque of 11.5 in.-lb (1.3 N-m). See figure below.
Figure 4: Plenum Deflector
Securing screws onto plenum2Secure deflector to plenum base1
Installing the Cisco NCS 4216
4
Installing the Cisco NCS 4216
Installing Plenum Assembly and Chassis in the Rack
Step 4 Position the air baffle and the side plate to the plenum. Secure the air baffle and the side plate using a maximum
torque of 11.5 in.-lb (1.3 N-m). See figure below.
Figure 5: Assembling Air Baffle to the Plenum
Side plate2Air baffle1
Plenum deflector4Plenum base3
Step 5 Secure the air baffle using a maximum torque of 11.5 in.-lb (1.3 N-m). See figure below.
Installing the Cisco NCS 4216
5
Installing the Cisco NCS 4216
Installing Plenum Assembly and Chassis in the Rack
Figure 6: Securing the Air Baffle Tray
-Securing air baffle to air plenum1
Step 6 Repeat Step-3 to Step-5 to complete the plenum assembly on the other side of the plenum base.
Step 7 Position the front cover hinge assembly on the plenum deflector. Secure the front cover using a recommended
torque of 11.5 in.-lb (1.3 N-m). See figure below.
Figure 7: Front Cover Hinge Assembly on the Plenum
-Front cover hinge assembly1
Installing the Cisco NCS 4216
6
Installing the Cisco NCS 4216
Installing Plenum Assembly and Chassis in the Rack
Step 8 Secure the cable brackets to the plenum deflector using a torque of 11.5 in.-lb (1.3 N-m). See figure below.
Figure 8: Cable Brackets to Plenum Deflector
Screws to secure brackets2Cable brackets1
Step 9 Position the plenum assembly to the rack and secure the cable brackets to the rack using a torque of 11.5 in.-lb
(1.3 N-m). See figure below.
Installing the Cisco NCS 4216
7
Installing the Cisco NCS 4216
Installing Plenum Assembly and Chassis in the Rack
Figure 9: Plenum Assembly to Rack
Plenum assembly2Rack1
-Securing the plenum to the brackets3
Step 10 Position cable guides on the router chassis.
Step 11 Guide the router chassis carefully into the plenum assembly. See figure below.
Installing the Cisco NCS 4216
8
Installing the Cisco NCS 4216
Installing Plenum Assembly and Chassis in the Rack
Figure 10: Chassis Assembly to Plenum in Rack
Cable guides on chassis2Plenum assembly1
-Securing screws to chassis onto rack3
Step 12 Position the door onto the router chassis and slide it into the rack. Secure the screws with a torque of 11.5
in.-lb (1.3 N-m). See figure below.
Installing the Cisco NCS 4216
9
Installing the Cisco NCS 4216
Installing Plenum Assembly and Chassis in the Rack
Figure 11: Door Assembly to Rack
Door2Chassis in plenum assembly1
-Securing door to the chassis onto rack3
Installing the Air Plenum (A907-F2B-AIR) in the Rack
This procedure installs the air plenum to orient the air flow in front-to- back direction in the NCS 4216 router.
Before performing any of the following procedures, ensure that power is removed from the DC circuit.
Statement 1074
Warning
This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal
use. Statement 39
Warning
For nominal voltage of -60 VDC, the input voltage range is from -40 to -72 VDC.
Note
Installing the Cisco NCS 4216
10
Installing the Cisco NCS 4216
Installing the Air Plenum (A907-F2B-AIR) in the Rack
Other manuals for NCS 4216
2
Table of contents
Other Cisco Network Router manuals
Cisco
Cisco ASR 9000 Series User manual
Cisco
Cisco NCS 4216 Instruction Manual
Cisco
Cisco 800 Series User manual
Cisco
Cisco 1750 Manual
Cisco
Cisco RV345 User manual
Cisco
Cisco SGE2000 User manual
Cisco
Cisco ASR 5500 User manual
Cisco
Cisco WS-C2960-24LC-S User manual
Cisco
Cisco WRT350N User manual
Cisco
Cisco OmniPeek NetFlow Analyzer s User manual
Cisco
Cisco Wireless Express 526 User manual
Cisco
Cisco ASR 920 series Instruction Manual
Cisco
Cisco ASR 1000 Series Operator's manual
Cisco
Cisco 761M User manual
Cisco
Cisco MWR 1941-DC - 1941 Mobile Wireless Router Manual
Cisco
Cisco ASR 9000 Series User manual
Cisco
Cisco Router Cisco 831 Manual
Cisco
Cisco 1750 User manual
Cisco
Cisco 860 Series Manual
Cisco
Cisco CGR 1120 User manual
