Cisco 1750 Installation guide

Cisco 1750 Router Hardware Installation Guide

78-6169-02

Cisco 1750 Router Overview

This chapter introduces the Cisco 1750 router, also referred to in this guide as “the

router,” and covers the following topics:

•Key Features

•Rear-Panel Ports and LEDs

•Front-Panel LEDs

•Router Memory

•Unpacking the Router

•Additional Required Equipment

Figure 1 shows the Cisco 1750 router.

Key Features

Cisco 1750 Router Hardware Installation Guide

78-6169-02

Figure 1 Cisco 1750 Router

Key Features

The Cisco 1750 router is a voice-and-data capable router that provides

Voice-over-IP functionality (VoIP) and can carry voice traffic (for example,

telephone calls and faxes) over an IP network. Using one to four WAN

connections, the router links small-to-medium-size remote Ethernet and

FastEthernet LANs to central offices. Table 1 lists the router key features.

17468

PWRACT

PORT0

PORT1

PORT0

SLOT1

PORT0

SLOT0 SLOT2ETH

PORT1 COL

Cisco

1700

SERIES

ROUTER

Table 1 Key Features

Feature Description

One FastEthernet (10/100BaseTX)

port

•Operates in full- or half-duplex mode (with manual

override available).

•Supports autosensing for 10- or 100-Mbps operation.

iii

Cisco 1750 Router Hardware Installation Guide

78-6169-02

Key Features

Cisco interface cards •Supports two slots for either WAN interface cards (WICs)

or voice interface cards (VICs).

•Supports one VIC-only slot.

•Supports the following WICs: ISDN BRI (U and S/T), 56-

or 64-kbps DSU/CSU, FT1/T1 DSU/CSU, high-speed

serial, dual-serial, and 2Async/Sync.

•Supports the following VICs: 2FXS, 2FXO, 2E&M.

•Changes in WAN interface configuration can be made as

your network requirements change.

Console port Supports router configuration and management from a

connected terminal or PC. Supports up to 115.2 kbps.

Auxiliary port Supports modem connection to the router, which can be

configured and managed from a remote location. Supports up

to 115.2 kbps.

Security slot Supports Kensington or similar lockdown equipment.

SNMP support Supports Simple Network Management Protocol (SNMP) to

manage the router over a network.

AutoInstall support Supports AutoInstall to download configuration files to the

router over a WAN connection.

Cisco ConfigMaker support Supports Cisco ConfigMaker application, a wizards-based

software tool, to configure a network that includes the

Cisco 1750 router.

Cisco Voice Manager support Supports Cisco Voice Manager to help you install and operate

voice and fax services over the IP network.

Compatible with Cisco Networked

Office stack

Stackable with other Cisco Networked Office stack products.

Table 1 Key Features (continued)

Feature Description

Rear-Panel Ports and LEDs

Cisco 1750 Router Hardware Installation Guide

78-6169-02

Rear-Panel Ports and LEDs

This section describes the router rear-panel ports and LEDs, which are shown in

Figure 2 and described in Table 2 and Table 3.

Figure 2 Rear-Panel Components and LEDs

Table 2 Rear-Panel Connectors

Connector/Slot Label/Color Description

Ethernet port 10/100-Mbps

ETHERNET

(yellow)

Router connection to the local Ethernet network. This

port autosenses the speed (10 or 100 Mbps) and duplex

mode (full or half) of the device to which it is connected

and then operates at the same speed and in the same

duplex mode.

Auxiliary port AUX

(black)

Modem connection for remote configuration using

Cisco IOS software.

Console port CONSOLE

(light blue)

Terminal or PC connection for local configuration using

Cisco IOS software.

+5, +12, -12 VDC

CONSOLE

AUX

Cisco 1750

10/100 ETHERNET

SLOT 2

SEE MANUAL BEFORE INSTALLATION

IN USE

VIC

2FXO

PVDM OK

SLOT 1

SLOT 2 OKFDXSLOT 0 OKSLOT 1 OK 100 LINK

THIS SLOT ACCEPTS ONLY VOICE INTERFACE CARDS

SLOT 0

Power

socket

Power switch

17469

FDX/100/LINK LEDs

Auxiliary port

Kensington-compatible

locking socket

WIC/VIC

slot 1

10/100-Mbps

Ethernet port

PVDM

OK LED

Slot 0

OK LED

Slot 1

OK LED

WIC/VIC

slot 0

Ground

wire

Console port

Slot 2

OK LED

IN USE

SEE MANUAL BEFORE INSTALLATION

IN USE

VIC

2FXS

IN USE

VIC

slot 2

Cisco 1750 Router Hardware Installation Guide

78-6169-02

Rear-Panel Ports and LEDs

Use the rear-panel LEDs during router installation to confirm that you have

correctly connected all cables to the router.

WIC/VIC slot SLOT 0 Supports either a Cisco WIC or VIC. For detailed

information, refer to the Cisco WAN Interface Cards

Hardware Installation Guide that comes with every

card.

WIC/VIC slot SLOT 1 Supports either a Cisco WIC or VIC. For detailed

information, refer to the Cisco WAN Interface Cards

Hardware Installation Guide that comes with every

card.

VIC slot SLOT 2 Supports one Cisco VIC. For detailed information, refer

to the Cisco WAN Interface Cards Hardware

Installation Guide that comes with every card.

Power socket +5, +12, –12

VDC

Router connection to the external power supply.

Protective earth Ground wire Router connection to earth ground by using a green and

yellow 14 AWG ground wire.

Table 2 Rear-Panel Connectors (continued)

Connector/Slot Label/Color Description

Table 3 Rear Panel LEDs

LED Label Color Description

FDX Green On—Ethernet port is operating in full-duplex mode.

Off—Ethernet port is operating in half-duplex mode.

100 Green On—Ethernet port is operating at 100 Mbps.

Off—Ethernet port is operating at 10 Mbps.

LINK Green On when the Ethernet link is up.

SLOT 0 OK Green On when either a WIC or VIC is correctly inserted in the

card slot.

SLOT 1 OK Green On when either a WIC or VIC is correctly inserted in the

card slot.

Front-Panel LEDs

Cisco 1750 Router Hardware Installation Guide

78-6169-02

Front-Panel LEDs

Use the router front-panel LEDs to determine network activity and status on the

Ethernet port and on the WIC and VIC ports. The front-panel LEDs are illustrated

in Figure 3 and described in Table 4.

Figure 3 Front-Panel LEDs

SLOT 2 OK Green On when a VIC is correctly inserted in the card slot.

PVDM OK Green On when a packet voice data module (PVDM) is

correctly inserted in the card slot.

Table 3 Rear Panel LEDs (continued)

LED Label Color Description

17470

PWR

ETH

ACT

PORT0

PORT1

PORT0

SLOT1

PORT0

SLOT0 SLOT2

PORT1 COL

Table 4 Front-Panel LEDs

LED Color

Cards

Supported LED Meaning

PWR Green – On when DC power is being supplied to the router.

OK Green – On when the router has successfully booted up and the

software is functional. This LED blinks during the

power-on self-test (POST).

Refer to the “OK LED Diagnostics” section in the

“Troubleshooting” chapter for information on how to use

this LED for router diagnostics.

ETH

vii

Cisco 1750 Router Hardware Installation Guide

78-6169-02

Front-Panel LEDs

ACT Green – Blinks when there is network activity on the Ethernet port.

COL Yellow – Blinks when there are packet collisions on the local

Ethernet network.

SLOTØ

PORTØ Green ISDN On when the first ISDN B channel is connected.

Serial and

CSU/DSU

Blinks when data is being sent to or received from the port.

2-port serial

VIC-2E&M

VIC-2FXO

VIC-2FXS

PORT1 – Serial and

CSU/DSU

Off.

Green ISDN On when the first ISDN B channel is connected.

2-port serial Blinks when data is being sent to or received from the port.

VIC-2E&M

VIC-2FXO

VIC-2FXS

Table 4 Front-Panel LEDs (continued)

LED Color

Cards

Supported LED Meaning

Front-Panel LEDs

viii

Cisco 1750 Router Hardware Installation Guide

78-6169-02

SLOT1

PORTØ Green ISDN On when the first ISDN B channel is connected.

Serial and

CSU/DSU

Blinks when data is being sent to or received from the port.

2-port serial

VIC-2E&M

VIC-2FXO

VIC-2FXS

PORT1 – Serial and

CSU/DSU

Off.

Green ISDN On when the first ISDN B channel is connected.

2-port serial Blinks when data is being sent to or received from the port.

VIC-2E&M

VIC-2FXO

VIC-2FXS

SLOT2

PORTØ Green VIC-2E&M Blinks when data is being sent to or received from the port.

VIC-2FXO

VIC-2FXS

PORT1 Green VIC-2E&M Blinks when data is being sent to or received from the port.

VIC-2FXO

VIC-2FXS

Table 4 Front-Panel LEDs (continued)

LED Color

Cards

Supported LED Meaning

Cisco 1750 Router Hardware Installation Guide

78-6169-02

Router Memory

This section describes the types of memory stored in the router and how to find

out how much of each the router has.

For instructions on how to upgrade memory in the router, refer to the “Installing

and Upgrading Memory and Data Modules” appendix in this guide.

Types of Memory

The router has the following types of memory:

•Dynamic RAM (DRAM)—This is the main storage memory for the router.

DRAM is also called working storage and contains the dynamic configuration

information. The router stores a working copy of Cisco IOS software,

dynamic configuration information, and routing table information in DRAM.

•Nonvolatile RAM (NVRAM)—This type of memory contains the startup

configuration.

•Flash memory—This special kind of erasable, programmable memory

contains a copy of the Cisco IOS software. The Flash memory structure can

store multiple copies of the Cisco IOS software. You can load a new level of

the operating system in every router in your network and then, when

convenient, upgrade the whole network to the new level. The Flash memory

on the router is stored on mini-Flash modules.

Router Memory

Cisco 1750 Router Hardware Installation Guide

78-6169-02

Amounts of Memory

Use the show version command to view the amount of DRAM, NVRAM, and

Flash memory stored in your router. The following example shows the output of

the show version command. The bold text displays the amount of memory stored

in this router.

1750# show version

Cisco Internetwork Operating System Software

IOS (tm) C1700 Software (C1700-SV3Y-M), Experimental Version

12.0(19980308:184442) [syaji-grammy-v6 189]

Compiled Mon 22-Mar-99 12:58 by syaji

Image text-base: 0x80008088, data-base: 0x806B2BB8

ROM: System Bootstrap, Version 12.0(1)XA1,RELEASE SOFTWARE (fc1)

Router uptime is 15 minutes

System restarted by power-on

System image file is “flash:syaji/c1700-sv3y-mz”

cisco 1750 (MPC860) processor (revision 0x00) with 24576K/8192K bytes

of memory.

Processor board ID 0000 (1314672220), with hardware revision 0000

M860 processor: part number 0, mask 32

Bridging software.

X.25 software, Version 3.0.0.

1 FastEthernet/IEEE 802.3 interface(s)

2 Low-speed serial(sync/async) network interface(s)

2 Voice FXS interface(s)

2 Voice E & M interface(s)

32K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x0

Other manuals for 1750

Table of contents

Other Cisco Network Router manuals

Cisco

Cisco CRS-1 - Carrier Routing System Router User manual

Cisco

Cisco WRVS4400N - Small Business Wireless-N Gigabit Security... User manual

Cisco

Cisco ME-C6524GS-8S User manual

Cisco

Cisco 910 User manual

Cisco

Cisco WLC 5700 Series User manual

Cisco

Cisco Catalyst 8500 Series Manual

Cisco

Cisco IR8340 Quick start guide

Cisco

Cisco 2600-DC Series User manual

Cisco

Cisco 2500 Series Operator's manual

Cisco

Cisco SRP500 User manual

Cisco

Cisco MWR 1900 Manual

Cisco

Cisco CRS User manual

Cisco

Cisco C1109-2PX Quick start guide

Cisco

Cisco 1700 series Original instructions

Cisco

Cisco 1603R User manual

Cisco

Cisco uBR10012 Universal Broadband Router... User manual

Cisco

Cisco RVS4000 - Gigabit Security Router User manual

Cisco

Cisco Linksys SGE2010P Manual

Cisco

Cisco OSR-7609 Installation and operation manual

Cisco

Cisco ASR 9901 Manual

Cisco

Cisco 880 Series Manual

Cisco

Cisco 15310-CL User manual

Cisco

Cisco ASR-920-12SZ-IM User manual

Cisco

Cisco ASA 5508-X User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

EnGenius

EnGenius ESR-9710 quick start guide

LevelOne

LevelOne FBR-1416 user manual

Dynacord

Dynacord Promatrix 6000 Operation manual

Lorex

Lorex F5D8230-4 Guide