Cisco 1003 User manual
Cisco 1003 and Cisco 1004 User Guide 1
Cisco 1003 and Cisco 1004
User Guide
This publication provides procedures for installing and configuring the Cisco 1003 and
Cisco 1004 routers.
Note All Cisco technical documentation and additional literature are available on
UniverCD, Cisco’sonlinelibraryofproductinformation. UniverCDis updatedandshipped
monthly, so it might be more up to date than printed documentation. UniverCD is available
both as a single CD and as an annual subscription. To order UniverCD, contact your local
sales representative or call Customer Service.
Throughout the text, “the router” means both the Cisco 1003 and Cisco 1004 routers,
unless indicated otherwise.
2Cisco 1003 and Cisco 1004 User Guide
Overview of the Cisco 1003 and Cisco 1004 Routers
Overview of the Cisco 1003 and Cisco 1004 Routers
The Cisco 1003 and Cisco 1004 routers provide Integrated Services Digital Network
(ISDN) capability in a small, desktop router. The routers connect small, remote sites with
Ethernet LANs to WANs.
The main difference between the two routers is that the Cisco 1004 router includes an
integrated network termination 1 (NT1) device and the Cisco 1003 router does not. The
ISDN service provider supplies the NT1 connection worldwide, except in North America,
where the NT1 device is supplied by the customer. Therefore, the Cisco 1004 router is for
use in North America, and the Cisco 1003 router is ideally suited for use elsewhere.
From the front, the outward appearance of the routers is the same.
H3864
Cisco 1003 and Cisco 1004 User Guide 3
Overview of the Cisco 1003 and Cisco 1004 Routers
From the back, the routers are the same with the following exceptions:
•The ISDN BRI (RJ-45) port is labeled “ISDN S/T” on the Cisco 1003 router and
“ISDN U” on the Cisco 1004 router.
•The product name—Cisco 1003 or Cisco 1004—is stamped on the chassis at the upper
left side (not shown).
Both routers include the following connectors:
•ISDN BRI (RJ-45)
•10BaseT Ethernet (RJ-45)
•Console (RJ-45)
•PCMCIA (Flash memory card) slot
•12 VDC power input
H2845
PCMCIA DC power
input
ISDN
(BRI)
10BaseT
Console
4Cisco 1003 and Cisco 1004 User Guide
System Specifications
System Specifications
Following are the specifications for the routers:
1. NVRAM = nonvolatile random-access memory.
2. The ISDN BRI port is labeled “ISDN S/T” on the Cisco 1003 router and “ISDN U” on the Cisco 1004
router. The Cisco 1004 router includes an integrated NT1 device.
Description Specification
Dimensions (H x W x D) 1.75 x 8.0 x 8.3" (4.4 x 20.3 x 21.1 cm)
Weight 2.6 lb (1.2 kg)
Input voltage, frequency,
and power dissipation 12 VDC output, minimum 0.5 A
Desktop external power supply: 100 to 240 VAC at
50 to 60 Hz, 1.0A input
Wall-mount external power supply: 120 VAC at 60 Hz input
Memory 4 MB DRAM (SIMM)
1 MB boot PROM
8 KB NVRAM1
WAN interface 1 ISDN BRI (RJ-45)2
Ethernet interface 1 10BaseT (RJ-45)
PCMCIA slot 1 Flash memory card (Type 2)
Console interface 1 asynchronous serial (RJ-45)
Operating environment 32 to 104
°
F (0 to 40°C)
Operating humidity 10 to 90%, noncondensing
EMI compliance Cisco 1003 router: FCC Class B, VDE Class B, Canadian
DOC Class B, EN55022 Class B (CISPR22 B), VCCI Class 2
Cisco 1004 router: FCC Class B, Canadian DOC Class B
Safety compliance Cisco 1003 router: UL 1950, CSA 22.2 No. 950,
EN60950:1992
Cisco 1004 router: UL 1950, CSA 22.2 No. 950
Cisco 1003 and Cisco 1004 User Guide 5
Canadian Department of Communications Notice
Canadian Department of Communications Notice
The Canadian Department of Communications label identifies certified equipment. This
certification means that the equipment meets certain telecommunications network
protective operational and safety requirements. The Department does not guarantee the
equipment will operate to the user’s satisfaction.
Before installing the equipment, users should ensure that it is permissible to be connected
to the facilities of the local telecommunications company. The equipment must also be
installed using an acceptable method of connection. In some cases, the company’s inside
wiring associated with a single line individual service may be extended by means of a
certified connector assembly (telephone extension cord). The customer should be aware
that compliance with the above conditions may not prevent degradation of service in some
situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications company cause
to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the
power utility, telephone lines and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly important in rural areas.
Caution Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as appropriate.
6Cisco 1003 and Cisco 1004 User Guide
Preparing to Install Your Cisco 1003 or Cisco 1004 Router
Preparing to Install Your Cisco 1003 or Cisco 1004 Router
It takes just a few simple steps to install your router. But before you install your router,
please read the safety information in this section.
Note Translations of the safety warnings in this document are available at the end of this
publication in the section “Translated Safety Warnings.” Additional guidelines related to
regulatory compliance and safety are available in the
Cisco
1003 and Cisco 1004 Public
Network Certification publication.
Safety Recommendations
Warning The warning symbol means danger. You are in a situation that could cause
bodily injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and standard practices for preventing accidents. To see translated
versions of this warning, refer to the section “Translated Safety Warnings” at the end of this
publication.
Because any device that uses electricity must be treated with respect, follow these
guidelines to ensure general safety:
•Keep the area clear and dust-free during and after installation.
•Keep tools away from walk areas where you and others could trip over them.
•Wearsafety glasses when working under anyconditions that might be hazardous to your
eyes.
•Do not perform any action that creates a potential hazard to people or makes the
equipment unsafe.
Cisco 1003 and Cisco 1004 User Guide 7
Preparing to Install Your Cisco 1003 or Cisco 1004 Router
Warning Before working on equipment that is connected to power lines, remove jewelry
(including rings, necklaces, and watches). Metal objects will heat up when connected to
power and ground and can cause serious burns or weld the metal object to the terminals. To
see translated versions of this warning, refer to the section “Translated Safety Warnings” at
the end of this publication.
•Locate the emergency power-off switch for the room in which you are working. Then,
if an electrical accident occurs, you can act quickly to shut off power.
•There are no user serviceable parts inside the router. Return the router if service is
required.
•Disconnect all power before doing the following:
—Installing or removing the router
—Working near power supplies
•Do not work alone if potentially hazardous conditions exist.
•Never assume that power is disconnected from a circuit. Always check.
•Look carefully for possible hazards in your work area, such as moist floors, ungrounded
power extension cables, and missing safety grounds.
•If an electrical accident occurs, proceed as follows:
—Use caution; do not become a victim yourself. Disconnect power to the router.
—If possible, send another person to get medical aid. Otherwise, assess the condition
of the victim and then call for help.
—Determine if the person needs rescue breathing or external cardiac compressions;
then take appropriate action.
8Cisco 1003 and Cisco 1004 User Guide
Preparing to Install Your Cisco 1003 or Cisco 1004 Router
Inspecting Your Router
Keep the router in the shipping container to prevent accidental damage until you have
determined where you want to install it; then proceed with unpacking it. Check the packing
list to ensure that you received the following items:
•Cisco 1003 or Cisco 1004 router
•Console cable (RJ-45-to-RJ-45)
•RJ-45-to-DB-25 adapter, for use with the console cable
•External power supply, desktop or wall-mount model
Note If your router ships with the desktop power supply, a 6-foot (1.8-meter) power cord
is included with the appropriate plug for the country to which the router is shipped.
•Label printed with the serial number and Media Access Control (MAC) address, which
is attached to the outside of the shipping container
•The warranty package, which includes the Product Registration form, service and
support information, and the Ordering Cisco Documentation publication.
Depending on the options you selected, your order might also include the following items:
•Optional PCMCIA Flash memory card
•Optional equipment (network connection cables)
•Optional companion publications
Inspect all items for shipping damage. If anything appears to be damaged or missing,
contact your system administrator or customer service representative.
Cisco 1003 and Cisco 1004 User Guide 9
Installing Your Cisco 1003 or Cisco 1004 Router
Installing Your Cisco 1003 or Cisco 1004 Router
Installing the router is quick and simple.
POWER SYSTEM SERIAL SERIAL LAN LAN COLLISION LINK
OK TX RX TX RX OK
POWER SYSTEM SERIAL SERIAL LAN LAN COLLISION LINK
OK TX RX TX RX OK
OR
Inspect your router.
Decide where to put your router:
on a desktop or wall.
Connect the cables to your network.
Connect the desktop
power supply (shown)
or the wall-mount
power supply.
Test your router installation.
Configure your router, if not
preconfigured, using your
console terminal.
H4200
12VDC
Insert your Flash memory card
(if supplied).
12VDC
12VDC
10 Cisco 1003 and Cisco 1004 User Guide
Installing Your Cisco 1003 or Cisco 1004 Router
Required Tools and Parts
Following are the tools and parts required to install your router:
•A 3/16-inch (0.476 cm) flat-blade screwdriver or socket screwdriver
•Wall-mount hardware, including screws, which you must provide
•A console cable (RJ-45-to-RJ-45)
•RJ-45-to-DB-25 adapter, for use with the console cable
•One interface cable for the LAN port (10BaseT Ethernet)
•One interface cable for the BRI ISDN (WAN) port
•An NT1 device for access to an ISDN through the BRI port (Cisco 1003 only)
The ISDN service provider provides the NT1 connection worldwide, except in North
America, where the NT1 device is supplied by the customer. The Cisco 1004 router
contains an integrated NT1 device. If you have a Cisco 1003 router, a separate NT1 device
is required.
The router can be placed on any flat surface or installed in any orientation, such as upside
downor onaverticalsurface. Therouterisdesigned to allowtrouble-freeoperation without
cooling fans, special equipment closets, or racks.
To avoid the possibility of the cables becoming disconnected, install your router in a
manner that minimizes strain on the cables.
Setting Your Router on a Desktop
Caution If you place the router on a desk or table, do not place anything on top of it that
couldrestrictairflow around the router or weighs in excess of10pounds(4.5kg).Excessive
weight on top of the router could cause damage.
This manual suits for next models
1
Table of contents
Other Cisco Network Router manuals
Cisco
Cisco MWR 1941-DC - 1941 Mobile Wireless Router Manual
Cisco
Cisco 3640 Series User manual
Cisco
Cisco ASR 9000 Series User manual
Cisco
Cisco cBR Series Manual
Cisco
Cisco RV042 - Small Business Dual WAN VPN Router User manual
Cisco
Cisco Linksys WET610N User manual
Cisco
Cisco WS-C3550-12G User manual
Cisco
Cisco XR 1200 series Installation manual
Cisco
Cisco ASR 9000 Series User manual
Cisco
Cisco ASR 1000 series Manual
Cisco
Cisco 1721 - VPN Security Router Bundle Manual
Cisco
Cisco SGE2000 Instruction Manual
Cisco
Cisco WS-C4507R Operating instructions
Cisco
Cisco RV180 User manual
Cisco
Cisco 815 User manual
Cisco
Cisco 7600 Series Assembly Instructions
Cisco
Cisco ASR 9000 Series User manual
Cisco
Cisco QuickVPN - PC Instruction Manual
Cisco
Cisco IR829 Manual
Cisco
Cisco ASR 1002-X Installation guide
