Cisco Catalyst 8200 Series User manual

Installing and Upgrading Field Replaceable Units

•Install and Remove Small Factor Pluggable, on page 1

•Removing and Replacing the Chassis Cover, on page 3

•Installing a DIMM, on page 4

•Removing a DIMM, on page 5

•Installing the M.2 Storage Module, on page 6

•Installing and Removing a NIM , on page 7

•Installing Pluggable Interface Module, on page 8

•Installing Drive Bays, on page 8

Install and Remove Small Factor Pluggable

Laser Safety Guidelines

Optical Small-Form Pluggable (SFPs) use a small laser to generate the fiber-optic signal. Keep the optical

transmit and receive ports covered whenever a cable is not connected to the port.

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or

view directly with optical instruments. Statement 1051

Warning

Ultimate disposal of this product should be handled according to all national laws and regulations. Statement

1040

Warning

Pluggable optical modules comply with IEC 60825-1 Ed. 3 and 21 CFR 1040.10 and 1040.11 with or without

exception for conformance with IEC 60825-1 Ed. 3 as described in Laser Notice No. 56, dated May 8, 2019.

Statement 1255.

Warning

To install an SFP module in your device, perform these steps:

Installing and Upgrading Field Replaceable Units

Step 1 Read the Safety Warnings section and disconnect the power supply before you perform any module replacement.

Step 2 Slide the SFP into the device connector until it locks into position

If the SFP uses a bale-clasp latch (see Laser Safety Guidelines section, the handle should be on top of the SFP

module.

Tip

Figure 1: Install a Small-Form Pluggable Module

Do not remove the optical port plugs from the SFP until you are ready to connect cabling.

Caution

Step 3 Connect the network cable to the SFP module.

Remove Small Form Pluggable Modules

Follow these steps to remove a Small Form Pluggable (SFP) from the device:

Step 1 Read the Safety Warnings section and disconnect the power supply before you perform any module replacement.

Step 2 Disconnect all cables from the SFP.

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or

view directly with optical instruments. Statement 1051

Warning

The latching mechanism used on many SFPs locks the SFP into place when cables are connected. Do not pull

on the cabling in an attempt to remove the SFP.

Caution

Step 3 Disconnect the SFP latch.

SFP modules use various latch designs to secure the module in the SFP port. Latch designs are not linked to

SFP model or technology type. For information on the SFP technology type and model, see the label on the

side of the SFP.

Note

Installing and Upgrading Field Replaceable Units

Remove Small Form Pluggable Modules

Figure 2: Disconnecting SFP Latch Mechanisms

Bale-clasp latch3Sliding latch1

Plastic collar latch4Swing and slide latch2

Use a pen, screwdriver, or other small straight tool to gently release a bale-clasp handle if you cannot reach it

with your fingers.

Tip

Step 4 Grasp the SFP on both sides and remove it from the device.

Removing and Replacing the Chassis Cover

Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement

1030

Warning

These are the steps to remove the chassis cover:

1. Confirm that the chassis is turned off and disconnected from the power supply or power supplies.

2. Place the chassis on a flat surface.

3. Remove the screws at top of the chassis cover.

4. Remove one screw from each side of the device as shown in the following figure.

Installing and Upgrading Field Replaceable Units

Removing and Replacing the Chassis Cover

Figure 3: Removing the Chassis Cover

5. Lift the chassis cover after you have removed all the screws.

To replace the chassis cover, place the cover evenly on the top of the device and use the screws to secure it

to the device.

Note

Installing a DIMM

There are two DDR4 DIMM slots. DIMMs have a polarization notch on the connecting edge to prevent

incorrect insertion.

Figure 4: DIMM Showing Polarization Notch

Polarization Notch1

Installing and Upgrading Field Replaceable Units

Installing a DIMM

These are the steps to install a DIMM:

1. Remove the chassis cover.

2. Locate the DIMM slot on thedevice. There are two DIMM slots in the chassis and you can install the

DIMM module on either of the slots.

3. Make sure that both latches on the DIMM connector are in the open position.

4. Orient the DIMM so that the polarization notch lines up with the polarization key on the connector.

5. Insert the DIMM into the connector.

6. Replace the chassis cover.

Removing a DIMM

These are the steps to remove a DIMM:

1. Remove the chassis cover.

2. Locate the DIMM module on the device. Refer to the Chassis-Internal section to identify and locate the

DIMM module.

3. Pull the latches away from the DIMM at both ends to lift the DIMM slightly. Pull the DIMM out of the

socket.

Installing and Upgrading Field Replaceable Units

Removing a DIMM

Figure 5: Removing a DIMM

4. Place the DIMM in an antistatic bag to protect it from ESD damage.

5. Replace the chassis cover.

Installing the M.2 Storage Module

The M.2 storage modules come with different storage capacities and can be replaced through the front panel

if required.

These are the steps to upgrade the M.2 storage module:

1. Power off of the system before replacing M.2.

2. Locate the M.2 storage module slot. Refer to Chassis - Front Panel to identify and locate the module.

Figure 6: Blank M.2 Slot

M.2 slot blank cover1

3. Loosen the screws that secures the M.2 blank cover or existing M.2 module in the slot.

Installing and Upgrading Field Replaceable Units

Installing the M.2 Storage Module

4. Plug in the new M.2 storage module in the same location and secure it with the screws.

M.2 module orientation with metal

carrier on top, M.2 module underneath.

2Securing screws (torque 3.9-5.4 in-lbs)1

Chassis cutout prevents M.2 installation

in wrong orientation.

Installing and Removing a NIM

These are the steps to install a NIM:

1. Locate the NIM slot on the front panel.

2. Loosen the screws to remove NIM blank cover.

3. Insert the NIM into the slot.

4. Tighten the screws to secure the NIM in the slot.

These are the steps to remove a NIM:

1. If the NIM is up and running, issue the following command to shut down the NIM gracefully before

removing it:

hw-module subslot slot 0/2 stop

If you do not shut down the NIM gracefully before removing it, the NIM card could get damaged.

Caution

2. Locate the NIM slot on the front panel.

3. Loosen the screws that secure the NIM.

4. Gently pull out the NIM from the slot.

Installing and Upgrading Field Replaceable Units

Installing and Removing a NIM

All module slots must have a module or blank installed for the product to work thermally and for safety

purposes.

Installing Pluggable Interface Module

To insert the PIM into the router, do these steps:

1. Insert and then gently push the PIM into the pluggable slot until firmly fixed.

2. Tighten the screw.

PIM Module2Securing screw1

Installing Drive Bays

If you have not ordered drives, the drive bay slot is closed with a blank cover.

These are the steps to install a drive in a drive bay:

1. The drive bay is in the front panel of the device. The bay is closed with a cover if there are no drives in

the slots.

2. Press the push button on the center of the cover and pull the cover out of the system to expose the slot.

3. Slide the drive into the slot.

Keep the drive bays covered when there are no drives installed in the slot.

Note

Installing and Upgrading Field Replaceable Units

Installing Pluggable Interface Module

Table of contents

Other Cisco Gateway manuals

Cisco

Cisco VG400 series Instruction Manual

Cisco

Cisco RF Gateway 1 Modules User manual

Cisco

Cisco VG420 Instruction Manual

Cisco

Cisco DPQ2425 User manual

Cisco

Cisco DPA 7610 Instruction Manual

Cisco

Cisco IG21-VZ-K9 User manual

Cisco

Cisco Linksys WAG54GX2 User manual

Cisco

Cisco WAG54G User manual

Cisco

Cisco Expressway Series User manual

Cisco

Cisco UNIFIED COMMUNICATIONS UC320W User manual

Cisco

Cisco Meraki Z3 User manual

Cisco

Cisco ASR 5000 Series Instruction Manual

Cisco

Cisco VG248 - Gateway Manual

Cisco

Cisco IP/VC 3526 How to use

Cisco

Cisco UPWL6028F User manual

Cisco

Cisco DPC2420 User manual

Cisco

Cisco EVM-IPVS-16A Quick start guide

Cisco

Cisco VG202 Manual

Cisco

Cisco DDR2200 Series Operating instructions

Cisco

Cisco DPC3940 User manual

Cisco

Cisco IG21 Series Manual

Cisco

Cisco Intelligent Wireless Access Gateway User manual

Cisco

Cisco DPR2320 Operating instructions

Cisco

Cisco 2621XM User manual

Popular Gateway manuals by other brands

LST

LST M500RFE-AS Specification sheet

Kinnex

Kinnex Media Gateway quick start guide

2N Telekomunikace

2N Telekomunikace 2N StarGate user manual

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Original instructions

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE user guide

Telsey

Telsey CPVA 500 - SIP Technical manual

RTA

RTA 460A-NNA4 Product user guide

Shaw

Shaw Gateway HDPVR user manual

ABB

ABB VSN900 Commissioning manual

Commander

Commander Pulse owner's manual

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E manual

NETGEAR

NETGEAR C6300BD installation guide

Amit

Amit CDW531AM user guide

HMS

HMS Netbiter EasyConnect EC150 user manual

Huawei

Huawei EchoLife HG620 user guide

AT&T

AT&T U-verse 3801 Replacement self-installation guide

Logic IO

Logic IO RTCU MX2 turbo Technical manual

Suttle

Suttle MediaMAX MXM-521 installation instructions