Ciro CYBERCHARGER 50002 User manual
cybercharger™
1 Cybercharger Assembly
1 Baery Power Harness
WARNING:
This indicaon alerts you to the fact
that ignoring the contents described
herein can result in potenal serious
injury or death if not followed.
CAUTION:
This indicaon alerts you to the fact
that ignoring the contents described
herein can or will result in material
damage and/or personal injury.
ATTENTION:
This indicaon alerts you to the fact
if you ignore this detail you will affect
the performance or funconality of
the product.
All Ciro products are designed for
"easy assembly" and/or "plug and
play". We recommend a competent
mechanic install our products, using
standard mechanical procedures to
assure a safe and successful
installaon.
Cybercharger wireless charging informaon:
- Smartphone makers recommend their phones are used in temperatures between 32°F and 95°F. Outside of that
range the phone performance (including baery performance, thus charging) can become irregular.
-Charging rates are regulated by the device being charged. The Cybercharger’s maximum charging rate is 15W.
-If you have a case on your phone. Check with the case supplier to verify it is actually wireless charging compable.
Cases thicker than 5mm or those that include metal or magnets in them may limit or prevent wireless charging,
and should not be used with the Cybercharger.
-The charger will use a standby current of approximately 20mA. If the vehicle has a healthy baery the standby
current draw will not affect baery performance. If the vehicle is likely to sit for more than 2 weeks unplug the
Cybercharger.
-It is normal for the phone and/or charger to become warm during use. If should not become too hot to touch; if it
feels uncomfortably hot, please disconnue use and contact Ciro. It may be a problem with an incompable case or
excessive gap between the phone and coil.
-Use cauon to protect the power cable plug if unplugging and removing the phone holder from the vehicle. The
cable must be secured and protected from water and unintended contact with other surfaces.
G0050002 REV. -
NOTE:
Ciro® warrants that products sold
hereunder to the original purchaser,
if maintained and operated under
normal condions, shall be free from
any defects in materials and
workmanship for a period of (3)
years from date of purchase, and a
lifeme warranty against LED failure.
Ciro will have no obligaon if the
customer cannot show proof of
purchase.
Warranty will not be granted unless
the part is properly installed and
maintained.
Ciro will not be liable for any
consequenal and incidental
damages, including labor, or non-Ciro
products.
Please visit our website Ciro3d.com
for our complete warranty policy.
parts included
FIG.1
(a)
Not included, shown
for illustraon only.
(-)
G0050002 REV. -
PAGE 2
Cybercharger installaon: Install the Ciro accessory ball mount according to the instrucons provided with that product.
1. Remove the large plasc nut (a) from the back of your Cybercharger. Slide the nut over the ball mount (-). FIG.1 (a)(-)
2. Pop the Cybercharger onto the ball and thread the nut onto it. Adjust the angle and then ghten the nut. To change the posion
loosen the nut, move the Cybercharger to the desired angle and then ghten the nut.
3. Connect the baery power harness to the baery and route the power cable to the mounted Cybercharger. Plug the power cable into the
boom of the Cybercharger.
Cybercharger phone fitment and usage:
-The phone holder includes an adjustable boom support leg meant to provide a durable, repeatable locaon for most popular phones. You may
need to loosen the lower most locking screw (b) and adjust the leg (c) to align the wireless charging coil to your phone. All phones are slightly
different and final placement will need to be determined by the user. The locking screw should then be ghtened to prevent unintended move-
ment. FIG.2 (b)(c)
-Do not overly ghten the clamping cam lever (d) before locking into place. Excessive force could lead to phone damage.
-The clamping cam lever (d) can be moved to the opposite side of the Cybercharger. Hold the side arms (e)(f) together and thread the lever all the
way out. Remove the clamping plate (g) and female thread plate (h). Reinstall them on the opposite side. Thread the cam lever back into place in
its new posion.
FIG.2
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h)
CIRO ACCESSORY PERCH MOUNT
1 Perch Mount
1 Installaon Kit
2 1/4-20 SHCS
2 M6 SHCS
2 Spacers
WARNING:
This indicaon alerts you to the fact
that ignoring the contents described
herein can result in potenal serious
injury or death if not followed.
CAUTION:
This indicaon alerts you to the fact
that ignoring the contents described
herein can or will result in material
damage and/or personal injury.
ATTENTION:
This indicaon alerts you to the fact
if you ignore this detail you will affect
the performance or funconality of
the product.
All Ciro products are designed for
"easy assembly" and/or "plug and
play". We recommend a competent
mechanic install our products, using
standard mechanical procedures to
assure a safe and successful
installaon.
G0050110 REV. C
NOTE:
Ciro® warrants that products sold
hereunder to the original purchaser,
if maintained and operated under
normal condions, shall be free from
any defects in materials and
workmanship for a period of (3)
years from date of purchase, and a
lifeme warranty against LED failure.
Ciro will have no obligaon if the
customer cannot show proof of
purchase.
Warranty will not be granted unless
the part is properly installed and
maintained.
Ciro will not be liable for any
consequenal and incidental
damages, including labor, or non-Ciro
products.
Please visit our website Ciro3d.com
for our complete warranty policy.
parts included
1. Park on a level surface and shut off the motorcycle. Ensure that the engine has me to cool before installaon.
Cover your tank with a clean towel or blanket to protect it.
2. Determine which side of the handlebars you would like the mount. Remove the two screws holding the clamp half in
place. Carefully support the original clamp half and controls to prevent any accidental damage. (Fig. 1)
FIG.1
FIG.3
FIG.2
3. Compare the screws you removed to the screws included in this kit. Both 1/4-20 and M6x1.00 threaded screws are
included to cover a variety of applicaons. Use the screws that match your motorcycle. Prepare the perch mount as
shown above. (Fig. 2)
4. Install the perch mount with spacers to the motorcycle, making sure to re-use the original clamp half. Tighten to factory
specificaons; approximately 72-108 in-lbs (8.1-12.2 Nm). (Fig. 3)
5. The posion of the top ball can be adjusted to provide adequate clearance for any installed accessory. Use a 5/32” hex
key to loosen and adjust the posion, checking final ghtness before riding. (Fig.4)
*If you have purchased any Ciro accessories to go with your ball mount, please refer to those instrucons to complete
your installaon.
FIG.4
FIG.3
Other Ciro Motorcycle Accessories manuals
