36 RP _STE(Tail tone elimination in communication through OFF/1,2,3 ... 10
repeater)
37 RPT _ RL{Dtlay the tall tone of repeater) OFF/1,2,3 •.• 10
38 PONMGS(Boot display) FULUMGS
39 ROGER(tone end oftnnsmlsslon) ON/OFF
40 RESET (Restore to ddault setting) VFO/ALL
12.2.-SHORTCUT MENU OPERATlON:
].-Press the key MENU,then press the key A or T to select the desired menu.
2.-Press the key MENU again, come to the parameter setting.
3.-Press the key A. or T to select the desired parameter.
4.-Press the key MENU to confirm and save, press the key EXIT to cancel setting or clear the input.
E E E
"MENU
NO. ..
MENU
NO.
.. ..
"MENU
NO.
PARAMEn:R ... PARAMEn:R AllAMEn:R
.
PARAMITER
G) CID @ @
-Note:
Under channel mode,the following menu settings are lnvaHd:CTCSS,DCS,W/N,PTT-ID,BCL,SCAN
ADD TO,S..CODE,CHANNEL NAME.Only the H/L power could be changed.
12.3.-"SQL" (SQUELCH),
-The squelch mute the speaker of the transceiver io the absence of recepdon. With the squelch level correctly
set, you will hear sound only while actually receiving signals and significantly reduces battery current
consumption. It is recommended that you set Level 5.
12.4.- FUNCTION "VOX" (VOICE OPERATED TRANSMISSION):
-This function is not necessary to push the [PTT] on the transceiver for a transmission. Transmission is
activated automatically by detecting the radio voice. When finish speaking, the transmission automatically
terminated and the transceiver will automatically receive signal. Be sure to adjust the VOX Gain level to
an appropriate sensitivity to allow smooth transmission.
12.5.- SELECT WIDEBAND OR NARROW BAND "WIN":
lo areas where the RF signals are saturated, you must use the narrow band of transmission to avoid
interference in adjacent channels.
12.6.-TDR (
D
UAL WATCH/DUAL RECEPTION),
This feature allows you to operate between frequency A and frequency 8. Periodically, the transceiver checks
whether a signal is received on another frequency that we have scheduled. If you receive a signal, the unit
14 will remain in the frequency until the received signal disappean.
12.
7
.- TOT(TRAN SM JSSIO N TIMER),
This function can automatically control the time we transmit each time you press (P1TI on the transceiver.
This feature is very useful to avoid overheating excessive power transiston of the transceiver. The transceiver
will be off transmission automatically once the set time.
12.8.-CTCSS/DCS:
In some cases only want to establish communications in a closed user group at a particular frequency or
channel, ror It will use "CTCSS" or code "DCS" for reception.
The "squdc
b
" opens only when receiving a frequency with "CTCSS" or codes "DCS" same as the programmed
in your transceiver. If codes of the received signal differs from those programmed in your transceiver, the
"squelch" will not open and the received signal can be beard.
Note:
-The use of "CTCSS" or "DCS" in a communication, does not guarantee complete confidentiality
communication.
12.9.-ANI
-ANI (Automatic Number Identification) is also known as PTT ID because an ID is transmitted when the
PTT button of the radio is pressed and/or released. This ID tells the di
s
patc
her which field radio was keyed.
Only could be set by PC software.
12.10.- DTMFST (
D
T
MF TON
E OF TRANSMJTTING CODE),
Finl you should set the PTI-ID as BOT/EOT/BOTH
-"OFF"-Under transmitting mode, you can't bear the DTMF tone, whUe you press the key to transmJt the
code or code automatically traosmJtted..
-"DT-ST"-Under transmitting mode, you can hear the DTMF tone, while you press the key to transmJt
the code.
-" ANI..
S
T
"- und
er transmitting mode, you can hear the DTM
F
tone, while the code automatically tran
s
mitted.
-"DT-ANl"-under transmitting mode, you can bear the DTMF tone, while you press the key to transmJt
the code or the code automatically transmitted..
12.11.- SC-REV(SCAN RESUME METHOD),
This transceiver allows you to scan memory channels, all the bands or part of the bands.
When the transceiver detects a communication, the scan will stop automatically.
Notea:
-"TO" (Time Operation):
Scanninc will atop when Jt detects an active signal The scannlnc will stop on each channel or
active frequency for a predetermined time, after that time the scan will resume automatically.
-"CO" (Carrier Operation):
The scannlnc will stop and remain in the frequency or channel, until the active sle;nal diaappean.
-"SE"(Searcb Operation):
The scanning will stop and remain In the frequency or channel after It detects an active signal.
15
