Chromalox CAB User manual

DIVISION

SECTION

CAB

SALES

REFERENCE

SERVICE REFERENCE

161-048224-001

Chromalox

(Supersedes PF412-6)

Installation, Operation

and

RENEWAL PARTS INDENTIFICATION

PF412-7

Type CAB and CABB

Forced Air Duct Heaters

Model Dimensions (In.)

(Note 1) (Note 2)

Weight Volts Phase kW No. No.

(Lbs.) Finstrips Ckts. ABC

CAB-62 CAB-611 25 120, 208, 1 or 3 6 6 1 10-3/4 15-7/8 11-1/2

CABB-62 CABB-611 240 or 480

CAB-122 CAB-1211 35 208, 240 or 480 1 or 3 12 9 1 15-3/8 18-1/2 14-1/8

CABB-122 CABB-1211

CAB-152 CAB-1511 40 208, 240 or 480 1 or 3 15 9 1 15-3/8 21-5/8 17-1/4

CABB-152 CABB-1511

CAB-202 CAB-2011 55 208 or 240 3 20 12 1 20-1/8 21-5/8 17-1/4

CABB-202 CABB-2011 480 1 or 3

CAB-252 CAB-2511 65 208 or 240 3 25 12 1 20-1/8 26-1/8 21-3/4

CABB-252 CABB-2511 480 1 or 3

—— CABB-3011 75 480 3 30 18 2 29-1/2 21-5/8 17-1/4

CAB-402 CAB-4011 90 208 or 240 3 40 18 2 29-1/2 27-3/8 23

CABB-402 CABB-4011 480 1 or 3

CAB-502 CAB-5011 110 208 or 240 3 50 18 2 29-1/2 33-1/8 28-3/4

CABB-502 CABB-5011 480 1 or 3

CAB-752 CAB-7511 200 208 or 240 3 75 27 3 44-7/16 42-1/8 37-3/4

CABB-752 CABB-7511 480 1 or 3

CAB-1002 CAB-10021 220 208 or 240 3 100 27 3 44-7/16 47-1/2 43-1/8

CABB-1002 CABB-10021 480 1 or 3

1. Iron sheath strip heaters — for sheath temperatures to 750˚F.

2. Chrome steel sheath strip heaters — for sheath temperatures to 950˚F.

Sensitive Bulb of

Thermostat

2 Holes 5/16-18 Tapped,

Each Side For Mounting

21/32

1-9/16”

2-1/4”

3-5/8”

Type CABB

Type CAB

3/4”

4-1/4”

2-1/4”

Special Cover for Side

or Bottom Terminals

Specifications –

GENERAL

WARNING: This heater is not intended for use in

hazardous atmospheres where flammable vapors,

gases, liquids or other combustible atmospheres are

present as defined in the National Electrical Code.

Failure to comply can result in explosion or fire.

1. Heat Construction Characteristics:

A. Finstrip®elements of either rust resisting iron or chrome

steel sheath, and aluminized steel fins.

B. 14 gage cold rolled steel frame painted with a black pow-

der coat paint.

C. Internal electrical connections consist of buss bars and

jumper straps of either Mn-Ni or Monel.

D. Field wiring terminals of heavy duty 3/8” diameter bolts of

either brass (iron sheath units) or stainless steel (chrome

steel sheath units) with hardware are provided for field

wiring connections.

2. Maximum temperatures — Type CAB and CABB air duct

heaters can generally be used at the following maximum tem-

peratures provided the minimum air velocity is maintained

uniformly through the heater. Table 2 is based on the standard

unit of 26 watts per square inch. If unit watt density is lower,

higher temperatures can be achieved. If higher watt densities

are used, outlet air temperature should be lowered.

3. Several heaters may be mounted in tandem as long as proper

controls are used to limit the maximum temperature attained. See

pressure drop curve G112S1 for effect of mounting in tandem.

4. Overtemperature protection — A thermal cutout should be

installed at the exhaust side of the heater for protection against

low airflow conditions.

INSTALLATION

WARNING: Hazard of Electric Shock. Disconnect

all power before installing heater.

1. Install heater into desired location in air duct with terminals

on bottom.

2. For installation where the duct heater is larger than the duct-

work, the duct area must be increased by a sheet metal transi-

tion. The slope of the transition piece on the upstream side is

limited to 30˚ as indicated in Figure 2. On the leaving side, the

slope should not be more than 45˚.

3. Make sure ductwork is of sufficient strength to contain the

heater. Refer to Table 1 for heater weights. Consult your local

sheet metal contractor if in doubt.

4. Two holes 5/16-18 tapped are located on each side of the

heater for mounting.

5. Air velocity must be sufficient enough to prevent element fail-

ure. See Table 2 for guidelines.

6. For protection against accidental air stoppage, mount a ther-

mal cutout on the exhaust side of the heater.

7. Insert thermal cutout sensitive bulb through duct and attach to

heater case with mounting clips provided.

8. DANGER: Hazard of Fire. Since these heaters are capa-

ble of developing high temperatures, extreme care should be

taken to:

a. Avoid installing heaters in an atmosphere containing com-

bustible gases and vapors.

b. Avoid contact between heater and combustible material.

c. Keep combustible material far enough away to be free of

the effects of high temperatures.

Air Velocity Max. Outlet Air Temp. (˚F)

(Ft./Sec.) Iron Sheath Chrome Steel Sheath

4 — 200

9 90 330

16 220 440

Air

Flow

30˚

Max

30˚

45˚

Duct Heater

4 Ft. Min. 4 Ft. Min.

1.0

.09

.08

.07

.06

.05

.04

.03

.02

.01

.009

.008

.007

.006

.005

.004

.003

.002

300 600 900 1200 1500 1800 2100

Triple Row of CAB

Double Row

Single Row

Velocity of Air F.P.M. (STD. Air)

Curve G112S1 - Resistance to Air Flow

Pressure Drop - In. of Water (LBS/In2= IN. of Water x 0.036)

Table 2

Figure 2

WIRING

WARNING: Hazard of Electric Shock. Any installation

involving electric heaters must be effectively ground-

ed in accordance with the National Electrical Code to

eliminate shock hazard.

1. All wiring should be done in accordance with the National

Electrical Code and with local codes by a qualified person.

2. Connect air heaters to same line voltage, phase and frequency

as on heater nameplate.

3. Teflon insulated nickel plated copper wire or buss bar is rec-

ommended for power connections to heater terminals and for

wiring runs in heated zones. When ambient temperature in

heated zone exceeds that for which insulated wire is recom-

mended use bare nickel-plated copper with porcelain beads,

tubing or buss bar. Consult local Chromalox representative.

4. Users should install adequate back-up controls and safety

devices with their electric heating equipment. Selection of

controls, thermostat, SCR units, contactors and etc. depends

on the degree of accuracy required, reliability, electrical rating

of heater and economic considerations.

5. Below is an example of standard CAB 122 480V 3P 12 kW

wired with recommended back-up controls (Figure 3).

OPERATION

WARNING: Users should install adequate back-up

controls and safety devices with their electric

heating equipment. Where the consequences of

failure may be severe, back-up controls are essen-

tial. Although the safety of the installation is the

responsibility of the user, Chromalox will be glad

to assist in making equipment recommendations.

1. Do not operate heaters at voltages in excess of that stamped

on the heater since excess voltage will shorten heater life.

MAINTENANCE

WARNING: Hazard of Severe Shock. Disconnect all

power to heater before servicing or replacing heaters.

1. Periodically clean terminals and terminal covers of dust and

corrosion to maintain good electrical connections and to per-

mit rapid heat dissipation. Use airblast, and be careful to avoid

damage to mica insulation.

2. Check for loose terminal connections.

Fused Switch

480V

Power

Supply

Heater

Contactor

Thermal Cutout

Fan

Motor 120/240

Control

Circuit

Figure 3 - Wiring Diagram

2150 N. RULON WHITE BLVD., OGDEN, UT 84404

Phone: 1-800-368-2493 www.chromalox.com

RENEWAL PARTS IDENTIFICATION

Model kW Heating Element

120 Volt 208 Volt 240 Volt 480 Volt

CAB-62

117-013851-001 (6) 117-013851-002 (6) 117-013851-003 (6) 117-013851-004 (6)

CABB-62

CAB-611 117-013852-001 (6) 117-013852-002 (6) 117-013852-003 (6) 117-013852-004 (6)

CABB-611

CAB-122

—— 117-013851-006 (9) 117-013851-007 (9) 117-013851-008 (9)

CABB-122

CAB-1211 —— 117-013852-006 (9) 117-013852-007 (9) 117-013852-008 (9)

CABB-1211

CAB-152

—— 117-013851-010 (9) 117-013851-011 (9) 117-013851-012 (9)

CABB-152

CAB-1511 —— 117-013852-010 (9) 117-013852-011 (9) 117-013852-012 (9)

CABB-1511

CAB-202

—— 117-013851-010 (12) 117-013851-011 (12) 117-013851-012 (12)

CABB-202

CAB-2011 —— 117-013852-010 (12) 117-013852-011 (12) 117-013852-012 (12)

CABB-2011

CAB-252

—— 117-013851-014 (12) 117-013851-015 (12) 117-013851-016 (12)

CABB-252

CAB-2511 —— 117-013852-014 (12) 117-013852-015 (12) 117-013852-016 (12)

CABB-2511

CABB-3011 30 —— —— —— 117-013852-012 (18)

CAB-402

—— 117-013851-018 (18) 117-013851-019 (18) 117-013851-020 (18)

CABB-402

CAB-4011 —— 117-013852-018 (18) 117-013852-019 (18) 117-013852-020 (18)

CABB-4011

CAB-502

—— 117-013851-022 (18) 117-013851-023 (18) 117-013851-024 (18)

CABB-502

CAB-5011 —— 117-013852-022 (18) 117-013852-023 (18) 117-013852-024 (18)

CABB-5011

CAB-752

—— 117-013851-026 (27) 117-013851-027 (27) 117-013851-028 (27)

CABB-752

CAB-7511 —— 117-013852-026 (27) 117-013852-027 (27) 117-013852-028 (27)

CABB-7511

CAB-1002

100

—— 117-013851-030 (27) 117-013851-031 (27) 117-013851-032 (27)

CABB-1002

CAB-10021 —— 117-013852-030 (27) 117-013852-031 (27) 117-013852-032 (27)

CABB-10021

Number in parenthesis indicates total quantity in unit.

Terminal Cover — 306-021921-001

Bulb Mounting Strap — 283-033234-001

Limited Warranty:

Please refer to the Chromalox limited warranty applicable to this product at

http://www.chromalox.com/customer-service/policies/termsofsale.aspx.

This manual suits for next models

Other Chromalox Heater manuals

Chromalox

Chromalox CAF-6 User manual

Chromalox

Chromalox ICH-18025 User manual

Chromalox

Chromalox DRA Series User manual

Chromalox

Chromalox UB-3502A User manual

Chromalox

Chromalox CAF-12 User manual

Chromalox

Chromalox HD3D Manual

Chromalox

Chromalox UB-2502A User manual

Chromalox

Chromalox PF411-10 User manual

Chromalox

Chromalox PF479-6 User manual

Chromalox

Chromalox NWHMTO User manual

Chromalox

Chromalox CXH-A-03 User manual

Chromalox

Chromalox NWHO-45 User manual

Chromalox

Chromalox HVH Series User manual

Chromalox

Chromalox ADH-005 User manual

Chromalox

Chromalox CVEP-C User manual

Chromalox

Chromalox TM Series Manual

Chromalox

Chromalox DH User manual

Chromalox

Chromalox V-2020 User manual

Chromalox

Chromalox CXH-C-03S User manual

Chromalox

Chromalox HVH-02-81 Owner's manual

Chromalox

Chromalox CAF-20215 Installation and operating instructions

Chromalox

Chromalox STAR-02A-11-F User manual

Chromalox

Chromalox CAF-12 Installation and operating instructions

Chromalox

Chromalox UB-23E Guide

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide