Christie SUHD983-P Instruction Manual
SUHD983-P Release Notes–Scaler Firmware v1.0.2.1, Ethernet v11 1
020-001868-01 Rev. 1 (11-2020)
Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
This document provides firmware update instructions and describes what is new in this firmware version for
the SUHD983-P.
Learn what has been updated in this release.
Scaler Firmware, v1.0.2.1
• Added RS232 control command for setting OPS/HDMI4 EDID:
• EDU: EDID UHD
• EDF: EDID FHD
• EDI: EDID information
• Resolved the issue where the OPS displayed a black screen.
• Added multi-window configuration in portrait mode.
• Resolved the issue where there was white noise from the panel after a factory reset.
Ethernet Firmware, v11
• Updated the web interface.
• Moved the Multi-window page under Picture settings.
• Added the Preset settings page.
• Added the UHD or FHD OPS/HDMI4 EDID options.
System connection for uploading
1. Plug in a USB memory to the service terminal.
Software Release Notes
SUHD983-P Release Notes–Scaler Firmware v1.0.2.1, Ethernet v11 2
020-001868-01 Rev. 1 (11-2020)
Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
2. Enter the Factory-Menu.
To enter the Factory-Menu by remote control:
SOURCE UP RIGHT LEFT DOWN
Before version 1.0.2.1-11
After version 1.0.2.1-11
3. Select Software Update (USB) and press the SEL button on the remote control.
You cannot enter Factory-Menu when set to Multi-Windows mode.
You must change Multi-Window mode to off to enter Factory-Menu.
USB Storage device
(That firmware for A/D B/D is stored)
(The file name of firmware is a 'SUHD983P.bin' )
Software Release Notes
SUHD983-P Release Notes–Scaler Firmware v1.0.2.1, Ethernet v11 3
020-001868-01 Rev. 1 (11-2020)
Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
4. Select USB Update.
In the case of proper USB storage devices, “Connected” appears.
5. If “Connected” appears, select USB Update again.
The firmware is updated automatically and the panel goes into standby mode after a successful
firmware update (about 30 seconds).
a. Reset the main power switch to turn the panel back on.
b. Once the firmware update is complete, perform an Initial Setting in the Factory-Menu.
c. After Initial Setting, power off the panel using the rocker-switch.
d. Wait at least 10 seconds and power the panel back on.
6. If the USB storage device is not compatible, a “Can’t Detect USB” message appears.
7. Ensure the filename is always be SUHD983P.bin regardless of the software version to upload correctly.
Software Release Notes
SUHD983-P Release Notes–Scaler Firmware v1.0.2.1, Ethernet v11 4
020-001868-01 Rev. 1 (11-2020)
Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
1. To use a static IP address, select Disable under DHCP.
Notice. The default static IP address is 192.168.10.10.
2. Select DHCP Enable to use a dynamic IP address.
If there is router, the IP address starts with 192.166.
If there is no router, the IP address starts with 169.254.
1. Go to Local Network Setting > Internet protocol version 4 (TCP/IPv4).
2. If DHCP is disabled, set the IP address and Subnet mask.
IP address must be a different address than the display.
IP address : 192.168.10.50
Subnet Mask : 255.255.255.0
Software Release Notes
SUHD983-P Release Notes–Scaler Firmware v1.0.2.1, Ethernet v11 5
020-001868-01 Rev. 1 (11-2020)
Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
3. If DHCP is enabled, select Obtain an IP address automatically.
The ping test checks the Ethernet connection.
1. Press Windows + R.
2. Type cmd and click OK.
3. Type ping –t 192.168.10.10.
Software Release Notes
SUHD983-P Release Notes–Scaler Firmware v1.0.2.1, Ethernet v11 6
020-001868-01 Rev. 1 (11-2020)
Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
4. Replace the IP address with the address of the display panel.
A response similar to below indicates the ping test was successful.
A response similar to below indicates the ping test failed.
Connect to the built-in web server open a Web browser (for example, Internet Explorer, Chrome) and follow
the instructions below.
1. In a web browser, go to the address of the display panel.
The web page provides all menu controls on the on-screen display.
2. To set a value, click Apply.
3. To display the current value, click Read.
4. To upgrade the Ethernet or Scaler firmware, go to the General settings page.
Software Release Notes
SUHD983-P Release Notes–Scaler Firmware v1.0.2.1, Ethernet v11 7
020-001868-01 Rev. 1 (11-2020)
Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
• Ethernet firmware update time: about 5 minutes.
File name : Ethernet_FW_V*.bin (* = version)
• Scaler firmware update time: about 8 minutes
File name : SUHD983-P.bin
For installation, setup, and user information, see the product documentation available on the Christie
website. Read all instructions before using or servicing this product.
1. Access the documentation from the Christie website:
• Go to this URL:http://bit.ly/2rO6SF6.
• Scan the QR code using a QR code reader app on a smartphone or tablet.
2. On the product page, select the model and switch to the Downloads tab.
Additional information on the LCD panels is available in the following documents.
• SUHD983-P LCD Panels Product Safety Guide (P/N: 020-001714-XX)
• SUHD983-P LCD Display Panels External Commands (P/N: 020-001766-XX)
• SUHD983-P LCD Panels Service Guide (P/N: 020-001723-XX)
Software Release Notes
SUHD983-P Release Notes–Scaler Firmware v1.0.2.1, Ethernet v11 8
020-001868-01 Rev. 1 (11-2020)
Copyright © 2020 Christie Digital Systems USA, Inc. All rights reserved.
Technical support for Christie products is available at:
• North and South America: +1-800-221-8025 or [email protected]
• Europe, Middle East, and Africa: +44 (0) 1189 778111 or [email protected]
• Asia Pacific
• Australia: +61 (0)7 3624 4888
• China: +86 10 6561 0240
• India: +91 (80) 6708 9999
• Japan: 81-3-3599-7481
• Singapore: +65 6877-8737
• South Korea: +82 2 702 1601
• Christie Professional Services: +1-800-550-3061 or NOC@christiedigital.com
Other manuals for SUHD983-P
2
Table of contents
Other Christie Monitor manuals
Christie
Christie FHD651-P User manual
Christie
Christie SUHD983-P Use and care manual
Christie
Christie Extreme Series Use and care manual
Christie
Christie Access Series User manual
Christie
Christie QUADHD84 User manual
Christie
Christie SUHD983-P User manual
Christie
Christie FHD492-XV User manual
Christie
Christie UHD982-P User manual
Christie
Christie 38-FP0001-01 User manual
Christie
Christie Secure II SUHD863-L User manual
Christie
Christie FHD553-X User manual
Christie
Christie MicroTiles User manual
Christie
Christie FHD553-X Use and care manual
Christie
Christie FHD554-XZ-R Use and care manual
Christie
Christie Velvet Core Series User manual
Christie
Christie Velvet CorePlus Series Assembly instructions
Christie
Christie Secure Series Assembly instructions
Christie
Christie FP400 User manual
Christie
Christie MicroTiles User manual
Christie
Christie 38-FP0002-01 User manual
