Chino D01M User manual
www.chinowing.com
D01M
SIGNAL
DECODER BOARD
USER MANUAL
V1.0.2
2022.10
2
www.chinowing.com
content
Custom CAN protocol ................................................. 错误！未定义书签。
Custom serial port protocol
disclaimer......................................................................................3
Product introduction .................................................... 错误！未定义书签。
Item list .........................................................................错误！未定义书签。
Main module .......................................................................................3
Product instruction .......................................................错误！未定义书签。
D01M schematic diagram ...................................................................4
D01M wire instruction diagram ..........................................................5
D01G Instruction for use ............................................................................6
D01G signal output setting ................................................................. 6
D01G output line sequence description .............................................8
D01M instruction for use ...........................................................................9
serial signal input .................................................. 错误！未定义书签。
signal output setting ............................................错误！未定义书签。 错误！未定义书签。
SBUS output setting ..........................................................................15
D01M indicator instruction ......................................................................16
firmware upgrade .........................................................错误！未定义书签。
Common question ........................................................错误！未定义书签。
Historical version .......................................................... 错误！未定义书签。
3
www.chinowing.com
Disclaimer
Please read this statement carefully before use. Once used,it is deemed to be
the recognition and acceptance of the entire content of this statement.Please
strictly follow this instruction to install and use the product. Shenzhen Chinowing
technology will not bear any legal responsibility for any results or losses caused by
improper use,installation,assembly and modification by users.
Product instruction
D01M analyzes TTL RS232 SBUS CAN signals for the joystick data of Chinowing
technology company remote control series. D01 is mainly designed for the sharing
of different application protocol requirements. D01 is divided into D01G and
D01M encoding and decoding. D01G is integrates in T30 T31 T40. D01M is used
for wireless transmission with V21 series or third party network video transmission.
Item list
Main module
4
www.chinowing.com
Accessories
Product instruction
D01M schematic diagram
XT30 power line *1
GH1.25 4pin *4
GH1.25 3pin *1
Power for module
（DC:7.4-60V)
For serial port and
device connection
For CAN data connection
5
www.chinowing.com
① XT30 power supply interface
support7.4-60V
② TTL/RS232 interface：full duplex serial port
For V21 seiral port signal input or third party video transmission.
③CAN interface:controling aera network
For remote control CAN custom data
④SBUS two outputs
Corresponding remote control SBUS output
⑤TTL interface：only support signal output
Serial port custom protocol for remote control assistant software
⑥RS232 interface：only support signal output
For remote control and device communication
⑦Signal indicator
Corresponding to each signal, the output is bright, and the input is off
⑧SET key
For upgrade operations
D01M wiring using diagram
6
www.chinowing.com
After the connection is complete, please refer to the following steps to check the
connection status.(This step will have some differences due to different
controllers)
CAN interface
TTL/RS232 interface
5V
5V
L
L
NC
D01M GND
GND application
equipment
D01M GND
GND application
equipment
H
H
TX
RX
SBUS interface
GND
GND
D01M S_1
S application
equipment-1
S_2
S application
equipment-2
D01G user manual
D01G signal output setting
When using T40N,T31N,T30N and other types,D01G is integrated
inside ,and the signal is output from the aviation plug 6 pin. If you use a
third-party link, you can select the corresponding signal output in the assistant
7
www.chinowing.com
software to use BSUS or serial port signal according to your needs.If you use a
serial port, confirm the type of the link serial port,which provides TTL and
RS232 level signal outputs, and also select the corresponding signal output in
the assistant software.
If you are using Chinowing series, you can ignore this setting,and it has
been configured to work normally before leaving the factory.
●Note that when switching the signal output, confirm the level type of your
device,switch the signal type first and then insert the signal line,such as TTL
equipment switching RS232 type may cause the TTL end to burn out due to the large
level difference.
● T40N T31N T30N and other D01G level output is off by default.
8
www.chinowing.com
D01G output line sequence description
In order to meet the various needs of users, the external output of 3 kinds
of signals shares a serial port,T40N,T31N,T30N and other ground control
stations,and the aviation socket 6pin distinguishes the line sequence when
different signals are output,as follows:
1,2,3pin corresponding line sequence
Signal
type
X
Y
GND
TTL
Tx
Rx
ground
RS232
Tx
RX
ground
S-BUS
S-BUS_1
S-BUS_2
ground
Pins4.5 and 6 are RS232 transparent serial ports,corresponding to COM6
ports of ground stations such as T30N,T31N and T30N
9
www.chinowing.com
D01M user instruction
Serial signal input
The D01M input only supports one level signal,TTL or RS232,and the level type
needs to be noted when purchasing, the corresponding level signal should be
selected according to the level type of the third-party link.
After the D01M is powered on, there is no signal input, and the LED is in the state of
running water light. When the signal output is turned on, the corresponding signal
LED is always on.
Signal output setting
The remote control assistant software“HZYT31”version number is “V1.3.2”.Turn
on the remote control and open the dedicated software HZY.Click “Channel
configuration”,if your version is without links , there will be “custom options”as
shown in the figure below.
10
www.chinowing.com
Custom CAN protocol
If you use the CAN protocol output,you need to open the CAN output,as
shown below:
The baud rate supports 50K-1M ，and the transmission frequency can be
customized and filled in according to your needs. Add custom data and
click”+”after sending , as shown in the figure below:
Every time you click “+”,a custom data setting box will popup,and the
custom data includes”standard identifier”and “extended
identifier”.Identifier type:There are standard identifiers and extended
identifiers. Data type:There are two types of data frame and remote frame,and
Table of contents
