CHIEF OXCM1U User manual
I N S T A L L A T I O N I N S T R U C T I O N S
Extra Large Outdoor Floor/Ceiling Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
OXCM1U
OXCM1U Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting systems
are properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located within the mounting system of the
OXCM1U mounts does not exceed 250 lbs (113.4 kg).
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Use this mounting system with other outdoor
products only.
WARNING: Always use two people or a mechanical lifting
device to safely lift and position equipment.
NOTE: The OXCM1U flat panel floor/ceiling mounts are
intended to be used with UL Listed ODAC Series
columns (not included): ODAC0203, ODAC0304,
ODAC0405, ODAC0506, ODAC0708.
--SAVE THESE INSTRUCTIONS--
Installation Instructions OXCM1U
3
DIMENSIONS
DIMENSIONS: INCHES
[MILLIMETERS]
1.91
48.4
0° HOLE
LOCKOUT
+5°AND -15°
HOLE LOCKOUT
-5° AND -20°
HOLE LOCKOUT
+7.6° HOLE
LOCKOUT
- 10°
2.48
63.0
-10° HOLE
LOCKOUT
OXCM1U Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions OXCM1U
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2 5/32” (included)
1/2”
9/16”
3/8"
C (4)
E (4)
[Interface Bracket Hardware Kit]
A (4) B (4) D (4)
F (4) G (4)
X (2)
M6x25mm M8x20mm M8x30mm
M6x16mm
.750x.323x.250 .750x.344x.500
Z (16)
1/4-20 x 5/8"
Y (4)
5/16 x 5/8"
5/16" P (1)
5/16-18 x 2"
L (2)
[Interface bracket]
K (1)
[Center wind shield]
W (4)
3/8"
N (1)
J (2)
[Side wind shield]
1/4-20 x 2"
Q (1)
1/4-20
1/4-20 x 1 1/4"
BB (4)
5/16-18 CC (8)
5/16"
DD (16)
1/4"
H (2)
[Mount assembly]
R (1)
5/16-18
S (2)
5/16" T (2)
1/4"
EE (1)
5/32"
U (2)
3/8-16 x 4" V (2)
3/8-16
M (1)
#10-24 x 1/2"
FF (1)
[X-large adapter] GG (2)
[Side cover]
JJ (1)
[X-large rail]
HH (4)
[Wind shield connector]
[Interface Lockout Bag] - (2) - (qty. per bag)
[Box-column Hardware Kit] - (2) - (qty. per bag)
AA (4)
1/4 x 3/4"
OXCM1U Installation Instructions
6
INSTALLATION
IMPORTANT ! : The following procedure assumes that:
• Two UL Listed ODAC Series Floor/Ceiling
Columns (not included) has been properly
installed following instructions provided with plate
and pipe.
Attaching Mount to ODAC Series Column
CAUTION: WATCH FOR PINCH POINTS! Do not place
fingers between movable parts.
1. Slide mount assemblies (H) onto ODAC Series Floor/
Ceiling Columns. (See Figure 1) or (See Figure 2)
2. Use two 3/8-16 x 4" hex head tapping bolts (U), four 3/8"
washers (W) and two 3/8-16 hex nuts (V) to secure each
mount assembly (H) to each column. (See Figure 1) or (See
Figure 2)
Figure 1
Figure 2
3. Install 1/4-20 x 1 1/4" button head cap screws (X) into each
mount assembly (H) to prevent column from rattling. (See
Figure 3)
Figure 3
1
2
(U) x 2
(W) x 4
(V) x 2
2
(H)
(to ceiling)
1
2
(U) x 2
(W) x 4
(V) x 2
2
(H)
(to floor)
(X) x 2
3
(H) x 2
Installation Instructions OXCM1U
7
4. Slide X-large rail (JJ) onto one of two assemblies (H)
attached to column. (See Figure 4)
Figure 4
5. Slide X-large rail (JJ) onto second assembly (J) attached to
column. (See Figure 5)
6. Slide two wind shield connectors (HH) into back grooves on
X-large rail (JJ) on both sides. (See Figure 5)
Figure 5
7. Tighten four bolts on back of each assembly to secure
extrusion in place.
Figure 6
8. Use four 1/4-14 x 3/4" hex flange bolts (AA) to secure two
side covers (GG) to ends of X-large rail (JJ). (See Figure 7)
Figure 7
Attach Wind Shield to Mount
1. Use two 5/16 x 5/8" hex head bolts (Y) and two 5/16"
washers (CC) to secure center wind shield (K) to back of
each mount assembly (H). (See Figure 8)
Figure 8
(JJ)
(H)
4
(HH) x 2
(HH) x 2
5
6
6
(JJ)
7
x 4 (per assembly)
(AA) x 4
(GG) x 2
8
(CC) x 2
(Y) x 2
1
(K)
(H)
OXCM1U Installation Instructions
8
2. Use two 1/4-20 x 5/8" cap screws (Z) and two 1/4" washers
(DD) to secure center wind shield (K) to sides of each mount
assembly (H). (See Figure 9)
Figure 9
3. Loosely install two 1/4-20 x 5/8" button head cap screws (Z)
and two 1/4" washers (DD) into two outside center holes on
center wind shields (K). (See Figure 10)
Figure 10
4. Hang two side wind shields (J) onto screws loosely installed
in Step 3 using teardrop holes in center slots. (See Figure
11)
5. Slide wind shields (J) horizontally to desired mounting
position. (See Figure 11)
Figure 11
6. Use four 1/4-20 x 5/8" button head cap screws (Z) and four
1/4" washers (DD) to secure two side wind shields (J) to two
center wind shields (K). (See Figure 12)
7. Tighten all six screws (Z).
Figure 12
(Z) x 2
2
(DD) x 2
(Z) x 2
3
(DD) x 2
(K) x 2
(J) x 2
4
5
5
teardrop holes
6
(DD) x 4
(K) x 2
(Z) x 4
(J) x 2
Installation Instructions OXCM1U
9
8. Use four 5/16-18 hex nuts (BB) and four 5/16" washers (CC)
to secure four wind shield connectors (HH) to side wind
shields (J). (See Figure 13)
Figure 13
9. Loosely install 1/4-20 x 5/8" button head cap screw (Z) and
1/4" washers (DD) into top right hole on left center shield
(K). (See Figure 14)
Figure 14
10. Hang x-large adapter (FF) onto screw loosely installed in
Step 9 teardrop mounting hole in upper left slot. (See Figure
15)
Figure 15
11. Use five 1/4-20 x 5/8" button head cap screws (Z) and five
1/4" washers (DD) to secure x-large adapter (FF) to two
center wind shields (K). (See Figure 16)
12. Tighten all six screws (Z).
Figure 16
(Center wind shields
hidden for transparency)
(BB) x 4
8
(CC) x 4
(J) x 2
(Z)
(DD)
9
(FF)
teardrop mounting hole
10
11
(Z) x 5
(DD) x 5
(FF)
(K) x 2
OXCM1U Installation Instructions
10
Attaching Interface Brackets to Display
1. Lower the latch mechanism on each interface bracket (L).
(See Figure 17)
Figure 17
2. Align the center of the interface bracket (L) with center of
screen. (See Figure 18)
NOTE: The diamond-shape hole in the bracket corresponds to
the center of the mount.
Figure 18
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
3. Select correct screws, spacers (if necessary) and universal
washers from the hardware bag (A-G) and attach brackets
(L) to back of screen. (See Figure 18)
Attaching Display to Ceiling Mount
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located within the mounting system of the
OXCM1U mounts does not exceed 250 lbs (113.4 kg).
1. Ensure that the latch mechanisms on interface brackets (L)
are already lowered. (See Figure 17)
2. While supporting both sides of display, lower display onto
ceiling mount, hooking top of interface brackets onto front of
ceiling mount. (See Figure 19)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! The display MUST
be centered on the ceiling mount.
3. Raise the latch mechanism on both interface brackets to
lock bracket in place. (See Figure 19)
Figure 19
(L) x 2
1
Latch
mechanism
Center of
bracket
(E or F) x 4
(A-D) x 4
(L) x 2
3
2
(G) x 4
(if necessary)
2
3
Latch
mechanism
(wind shield hidden for clarity)
This manual suits for next models
1
Table of contents
Other CHIEF TV Mount manuals
CHIEF
CHIEF XPAU User manual
CHIEF
CHIEF MSB-6053 User manual
CHIEF
CHIEF J Series User manual
CHIEF
CHIEF Flat Panel Wall Plate Accessory FSA-1001 User manual
CHIEF
CHIEF MSBU User manual
CHIEF
CHIEF Video Wall Mount WM-46UN Chief User manual
CHIEF
CHIEF FHB3017 User manual
CHIEF
CHIEF MSBU User manual
CHIEF
CHIEF MSB-6309 User manual
CHIEF
CHIEF FSA-1007 User manual
CHIEF
CHIEF PSM-2126 User manual
CHIEF
CHIEF TS525TU User manual
CHIEF
CHIEF FHB7017 User manual
CHIEF
CHIEF FHB*038 User manual
CHIEF
CHIEF MSM Series User manual
CHIEF
CHIEF Kontour KRA209 User manual
CHIEF
CHIEF PSB-2306 User manual
CHIEF
CHIEF FSB-4243 User manual
CHIEF
CHIEF PSBU User manual
CHIEF
CHIEF KSA1250 User manual
