CHIEF GPM-110 User manual
CHIEF MANUFACTURING INC. 8807-000019 Rev. A
1-800-582-6480 952-894-6280 FAX 952-894-6918 2004 Chief Manufacturing
8401 EAGLE CREEK PARKWAY, STE. 700 www.chiefmfg.com
SAVAGE, MINNESOTA 55378 USA 06/04
INSTALLATION INSTRUCTIONS
Small Flat Panel
Tilt Wall Mount (GPM-110)
BEFORE YOU BEGIN
• CAUTION: To prevent damage to your display, which could affect or void the Factory warranty,
thoroughly study all instructions and illustrations before you begin to install the mount brackets. Pay
particular attention to the “Important Warnings and Precautions” on Page 2.
• If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-6480.
The GPM-110 tilt wall mount is designed to adapt to
VESA® 75mm/100mm compliant displays.
The GPM-110 allows the user to adjust the viewing angle
of the mount + 15 degrees horizontally or vertically by
hand, depending on the preferred type of installation.
After adjusting the display to the desired angle, the user
can lock the mount into a fixed position. The user can
easily remove the display from the wall bracket when the
mount is unlocked.
GPM-110
Instruction Manual GPM-110
2
IMPORTANT WARNINGS and CAUTIONS!
WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow
the instructions.
CAUTION ACAUTION alerts you to the possibility of damage or destruction of equipment if you do not
follow the corresponding instructions.
• WARNING Improper installation can result in serious personal injury! Make sure that the
mounting surface can support a redundant weight factor five times the total weight of
the equipment: if not, reinforce the mounting surface structural members before
installing the GPM-110.
• WARNING Be aware of the potential for personal injury or damage to the unit if it is not
adequately mounted.
• WARNING The installer is responsible for verifying that the mounting surface to which the GPM-
110 is anchored will safely support the combined load of all attached components or
other equipment.
• WARNING The combined weight of the display placed on the GPM-110 must not exceed 40 lbs.
(18.1kg), the maximum load capacity of the mount.
• WARNING Watch for pinch points. Do not put your fingers between movable parts.
• WARNING Make sure the mount is correctly oriented.
• CAUTION Check the unit for shipping damage before you begin the installation.
• CAUTION If your monitor uses a longer screw size other than those included in the kit, DO NOT use
the screws provided with the mount. Use the screws provided with your monitor or contact
the manufacturer. Using the wrong screws could result in damage to your monitor.
CONTENTS
TOOLS REQUIRED FOR INSTALLATION....................................2
GPM-110 TILT MOUNT KIT...........................................................3
Installation Instructions...................................................................4
Installing the Wall Bracket (Step 1) ............................................4
OPTION A (Drywall Installation Procedures)..........................4
OPTION B (Wall Stud Installation Procedures) ......................4
Attaching the VESA Bracket to the Display (Step 2)..................5
Flushed Mount ........................................................................5
Recessed Mount .....................................................................5
Mounting the Display on the Wall Bracket (Step 3)....................6
Locking the Display on the Wall Bracket (Step 4) ......................6
TOOLS REQUIRED FOR INSTALLATION
• Phillips screwdriver
• Drill and drill bits
NOTE: Other tools may be required depending on your method of installation.
Instruction Manual GPM-110
3
GPM-110 TILT MOUNT KIT
Unpack the carton. Verify the kit contains the contents shown in Table 1. Read installation instructions completely. If
you are missing any of the listed components, please contact Customer Service at 1-800/582-6480.
Table 1. GPM-110 Tilt Mount Kit
ITEM
NUMBER DESCRIPTON QTY NOTES
10 BRKT, VESA INTERFACE 1
20 BRKT, WALL MOUNT 1
30 ANCHOR, HOLLOW WALL 4
DRYWALL
MOUNTED
40 PHILLIPS HEAD WOOD SCREW, 2-1/2” 2
SINGLE STUD
MOUNTED
50 NYLON WASHER 2
60 PHILLIPS PAN HEAD MACHINE SCREW, M5 X 10MM 2
TILT ADJUSTMENT
70 PHILLIPS PAN HEAD MACHINE SCREW, M4 X 10MM 4 FLUSH MOUNT
80
PHILLIPS PAN HEAD MACHINE SCREW, M4 X 20MM
(USE WITH 90) * 4
90 3/8” NYLON SPACER 4
100
PHILLIPS PAN HEAD MACHINE SCREW, M4 X 30MM
(USE WITH 110) ** 4
110 3/4” NYLON SPACER 4
RECESSED
MOUNT
Instruction Manual GPM-110
4
Installation Instructions
NOTE: Read the “Important Warnings and Precautions” on
Page 2.
Installing the Wall Bracket (Step 1)
The wall bracket can be mounted vertically or horizontally.
Mounting the bracket vertically allows you to tilt the display up
and down. Mounting the bracket horizontally allows you to pivot
the display side-to-side.
To install the wall bracket, perform Option A or Option B as
applicable.
OPTION A (Drywall Installation Procedures)
A. Determine the exact mounting location prior to
installation, considering screen size as well as the mount
tilt radius.
B. Position the wall bracket (20) in the vertical position or
the horizontal position, as needed.
C. Using the wall bracket (20) as a template at the desired
mounting location, mark the location of the four outer
mounting holes.
NOTE: This procedure applies to a minimum drywall
thickness of ½” inch (12.7 mm).
D. Using a 3/8-inch drill, drill four pilot holes at the locations
marked in Step 1.A.
E. Install an anchor (30) in one of the pilot holes and tighten
anchor bolt until it is fully seated (see Figure 1).
F. Remove and retain bolt from anchor (30) and repeat
Step 1.E and 1.F for three remaining anchors (30).
G. Using four bolts, with washers installed, secure wall
bracket (20) to wall.
OPTION B (Wall Stud Installation Procedures)
A. Determine the exact mounting location prior to
installation, considering screen size as well as the mount
swing and extension radius.
B. Position the wall bracket (20) in the vertical position or
the horizontal position, as needed.
C. Locate stud and, using wall bracket (20) as a template at
the desired height, mark the location of the two center
mounting holes.
D. Using the two wood screws (40), secure wall bracket
(20) to wall.
Step 1
Installing Wall Bracket – Vertically
Installing Wall Bracket – Horizontally
A
%%c0.375 (PREDRILL HOLE)
INSERT ANCHOR INTOPPREDRILLED HOLE
CW
ANCHOR BARBP(STOPS ANCHOR ROTATION)
#10-24
Screw 0.375 (Predrill Hole)
Insert anchor into
predrilled hole
A
nchor Ba
r
b
(Stops anchor rotation)
A
nchor (30)
Turn 10-24 screw clockwise
until anchor fully seats
against back side of wall
CW
Figure 1. Anchor Installation
A
B
A
(Corner Holes)
B
(Center Holes)
Instruction Manual GPM-110
5
Attaching the VESA Bracket to the Display
(Step 2)
NOTE: Choose the instructions, listed below, that apply to the
type of installation you want.
• Flush Mount Applications do not use spacers. The
display is attached to the mount with four screws.
• Recessed Mount Applications use spacers. The display
is attached to the mount with four screws and four
spacers.
CAUTION: If monitor uses a screw size other than those
included in the kit, DO NOT use the screws provided.
Using the wrong screws could result in damage to your
monitor.
Flushed Mount
A. Place the VESA bracket (10) on the display.
B. Align the hole-pattern of your display with the hole-
pattern on the VESA bracket (10).
C. Attach VESA bracket (10) to the display using four
M4 X 10mm screws (70) provided.
Recessed Mount
NOTE: Use one of the following screw and spacer
combinations: (80 with 90) or (100 with 110).
A. Select four screws (80 or 100) for the Recessed
application.
B. Select the four spacers (90 or 110) for the Recessed
application.
C. Set four spacers (90 or 110) over the four mounting
holes on your monitor.
D. Install four screws (80 or 100) into the top mounting
holes of your display.
Step 2
Recessed Mount
Flushed Mount
70
10
80 or 100
90 or 110
Instruction Manual GPM-110
6
Mounting the Display on the Wall Bracket
(Step 3)
A. With the aid of another person (if necessary), lift the
display up to the wall bracket (20) over the four mounting
pins.
B. Align the mounting pins on the display with the slots in
the wall bracket (20), and set the display into place.
C. Verify that the display tilts in the wall bracket (20).
• For displays that are mounted vertically, tilt the
display + 15 degrees upward and downward.
• For displays that are mounted horizontally, pivot the
display + 15 degrees from side-to-side.
Locking the Display on the Wall Bracket
(Step 4)
A. Assemble a washer (60) over each M5 screw (70).
Install the two M5 (70) screw assemblies into the tapped
holes located on the side on the wall bracket (20).
B. Set the display into the desired position. Tighten the M5
screw (70) until friction holds the display stationary.
Step 3
Assemble the Brackets
Step 4
Install the M5 Screw – Vertical Tilt
Install the M5 Screw –
Horizontal Pivot
Tapped
Hole
60
70
Tapped
Hole
60
70
Table of contents
Other CHIEF Rack & Stand manuals
CHIEF
CHIEF RPA145 User manual
CHIEF
CHIEF SSB-171 User manual
CHIEF
CHIEF CMA100 User manual
CHIEF
CHIEF JWDV User manual
CHIEF
CHIEF PACHFK2 User manual
CHIEF
CHIEF KRA225 User manual
CHIEF
CHIEF CM2C40 User manual
CHIEF
CHIEF MFAUBSP User manual
CHIEF
CHIEF Kontour KRA235 User manual
CHIEF
CHIEF MSM Series User manual
CHIEF
CHIEF MF1 Series User manual
CHIEF
CHIEF FPM SERIES User manual
CHIEF
CHIEF 25MWR Service manual
CHIEF
CHIEF SL-236 Operating and safety instructions
CHIEF
CHIEF PWRSKU User manual
CHIEF
CHIEF SSB-083 User manual
CHIEF
CHIEF FSD-4100 User manual
CHIEF
CHIEF FMSSTRM User manual
CHIEF
CHIEF KTA-1000 User manual
CHIEF
CHIEF QMP1T User manual
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
