CHIEF FPM SERIES User manual

8803-000034 Rev. B 05/05

CHIEF MANUFACTURING INC. 1-800-582-6480, Fax: 1-877-894-6918, Email: [email protected]

INSTALLATION INSTRUCTIONS

FPM SERIES

SMALL FLAT PANEL DISPLAY

PITCH-ADJUSTABLE WALL MOUNT

Exclusive Q2™ Mounting System

Prior to assembly, unpack carton completely and verify contents.

If you are missing any of the following components, please contact Customer Service at 1-800/582-6480

(1) FPM Wall Bracket (4) Drywall Anchor

(2) Wood Screw (2) Washer, Flat, .25 ID X .56 OD

BEFORE PROCEEDING, READ INSTALLATION INSTRUCTIONS COMPLETELY

Flat Panel Displays are Extremely Fragile.

If Monitor Uses a Screw Size Other Than M4 X 10mm (M4 X 20mm),

DO NOT USE M4 Screws Provided. Monitor Damage Could Occur.

Interface Bracket Installation:

1. See installation procedures accompanying your mounting bracket.

Optional Latching Flag Placement:

1. Remove Phillips head screw, Nylock nut and latching flag (see Figure 2).

2. Reposition latching flag and secure using Phillips head screw, Nylock nut.

CAUTION!

Figure 1

Remove screw

and nut Move latch

Figure 2

Drywall Installation Procedures:

Minimum Sheetrock Thickness ½ Inch.

2. Using the wall bracket as a template at the desired mounting location, mark the location of the four

outer mounting holes.

3. Using a 3/8-inch drill, drill four pilot holes

to a minimum depth of 1 1/2”

at the locations marked

in Step 2.

4. Install an anchor bolt in one of the pilot holes and tighten anchor bolt until it is fully seated (see

Figure 3).

5. Remove and retain bolt and washer from anchor and repeat Step 4 and 5 for three remaining anchor

bolts.

6. Using four bolts, with washers installed, secure wall bracket to wall.

Wood Stud Installation Procedures:

1. Locate stud and, using wall bracket as a template at the desired height, mark the location of the two

center mounting holes.

2. Install a .25 ID x .06 OD flat washer on each of the two wood screws.

3. Using the two wood screws with flat washers installed, secure wall bracket to wall.

Mounting Display with Interface Bracket to Wall Bracket:

1. Make sure the latching flag on the mounting bracket is in the unlocked position (see Figure 4).

2. Place your small flat panel display; with interface bracket attached, onto the wall bracket, making

sure it is securely seated.

3. Lower the latching flag on the wall bracket, locking small flat panel display in place (see Figure 5).

Figure 5

ON!

Outer Mountin

Holes

Figure 4

Locke

Unlocke

%%c0.375

(

PREDRILL HOLE

)

INSERT ANC HO R INTOPPREDRILLED HOLE

NCHOR BARBP

(

STOPSANCHORROTATION

)

#10-24 Screw Ancho

0.375

(

Predrill Hole

)

Insert anchor into

predrilled hole Anchor Barb

(Stops anchor rotation)

Turn 10-24 screw clockwise

until anchor fully seats

against back side of wall

Figure 3

Inner Mountin

Holes

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 