Chicago Electric 35633 User manual

Table of contents

Other Chicago Electric Grinder manuals

Chicago Electric

Chicago Electric 99675 Installation manual

Chicago Electric

Chicago Electric 95219 Parts list manual

Chicago Electric

Chicago Electric 42934 User manual

Chicago Electric

Chicago Electric 94071 Installation manual

Chicago Electric

Chicago Electric 91223 User manual

Chicago Electric

Chicago Electric 42203 User manual

Chicago Electric

Chicago Electric 91222 User manual

Chicago Electric

Chicago Electric 98107 Installation manual

Chicago Electric

Chicago Electric 94071 User manual

Chicago Electric

Chicago Electric 91223 User manual

Chicago Electric

Chicago Electric 94071 Assembly instructions

Chicago Electric

Chicago Electric 65519 Assembly instructions

Chicago Electric

Chicago Electric 91222 User manual

Chicago Electric

Chicago Electric 67648 Installation manual

Chicago Electric

Chicago Electric 93179 Installation manual

Chicago Electric

Chicago Electric 65519 Installation manual

Chicago Electric

Chicago Electric Chicago 46237 User manual

Chicago Electric

Chicago Electric 69085 User manual

Chicago Electric

Chicago Electric 40432 Installation manual

Chicago Electric

Chicago Electric 31309 Quick reference guide

Chicago Electric

Chicago Electric 66876 Installation manual

Chicago Electric

Chicago Electric 97588 Installation manual

Chicago Electric

Chicago Electric Chicago 46237 Installation manual

Chicago Electric

Chicago Electric 44141 User manual

Popular Grinder manuals by other brands

Parkside

Parkside PWS 230 C3 Translation of the original instructions

SUHNER ABRASIVE

SUHNER ABRASIVE ASC 9 Technical document

PTA

PTA P1322 Operation manual

Crown

Crown CT13313 Original instructions

Parkside

Parkside 280250 instructions

Climax

Climax VM2150 Series operating manual

Jet

Jet JPSG-618M1 Operating instructions and parts manual

Makita

Makita GA4030 instruction manual

DeWalt

DeWalt DWEN202 Original instructions

Grizzly

Grizzly G2790 instruction manual

Fein

Fein MSf843-1a Original instructions

Bosch

Bosch GWS 14,4 V PROFESSIONAL operating instructions

RAMSET

RAMSET CBAGR18 owner's manual

Bosch

Bosch 8-115 Z Original instructions

STEELE PRODUCTS

STEELE PRODUCTS SP-PB008 owner's manual

MW TOOLS

MW TOOLS ME15W manual

Caravaggi

Caravaggi SP 20 User & maintenance manual

SUHNER ABRASIVE

SUHNER ABRASIVE UWK 10-R125 Technical document

9” ANGLE GRINDER

MODEL 35633

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

For technical questions and replacement parts, please call 1-800-444-3353

Copyright © 1996 by Harbor Freight Tools®. All rights reserved. No portion of this manual

or any artwork contained herein may be reproduced in any shape or form without the

express written consent of Harbor Freight Tools.

®

Warning: There are certain applications for which this

tool was designed. Harbor Freight Tools strongly rec-

ommends that this tool not be modified and/or used

for any application other than which it was designed.

All accessories must be rated for at least the RPM

speed recommended on the tool’s warning label.

Wheels and other accessories running over rated

speed can fly apart and cause injury.

For safest operation, it is recommended that only these

accessories be used with this product:

Abrasive Cut-Off Discs and Wheels - Flap Wheels - Wire Brushes - Wire Wheel Brushes

Always use an approved and proper guard when using the above mentioned accessories. Each

accessory must have the correct arbor size and must fit properly on the shoulder bushing. Make

sure accessories are tightened down securely.

CAUTION: NEVER INSTALL A CARBIDE TIPPED OR STEEL CIRCULAR SAW BLADE FOR USE ON

THIS ANGLE GRINDER. NEVER INSTALL A WOOD CARVING BLADE, CARVING DISC WITH SAW

CHAIN CUTTERS, OR A CUTTING CARVING DISC ON THIS ANGLE GRINDER.

Revised Cover Page 05/03

4

VOLTAGEWARNING

Beforeconnectingthe tool toapower source (receptacle,outlet,etc) be surethevoltage supplied is

aboutthe same as that specifiedon the nameplate of thetool. If on says 120Vand theother says 110V

thenthere will benocomplications. Never try toplug a 110Vtoolintoa220Voutlet,ortheotherway

around. Theplugandoutlet have completely differentshapes. Thisisbecause a power source witha

voltagegreater than that specifiedon the toolcanresult in aSERIOUS INJURYtothe user -- aswell

as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with

voltage(110V)lessthanthenameplaterating(220V)isharmfultothemotor.

EXTENSIONCORDS

Your tool isdouble insulated andhas a two-prongplug, you mayuse either atwo - orthree - prong

extensioncord. Onlyuserounded jacket extension cordslistedby the Underwriters Laboratories(UL).

Makesurethe cord isratedfor outdoor use ifyouplan on usingthetool outside; if youplanon indoor

use,you may also use aoutdoor ratedcord. Extension cords rated for outdooruse have the letters

“WA”on the cord jacket.

Theextensioncordmusthaveaminimumwiresizedependingontheamperageofthetoolandthe

lengthoftheextensioncord. This size issignifiedbyitsAWG(AmericanWireGauge)rating;the

smallerthegauge,the greater thecable’scapacity. Ifyou areusingtwo or more cords,thetotallength

ofthecombinedcords must be used todeterminetheminimumAWG rating. Eachofthecordsused

mustmeetthisrating.

Your tool asa 14amp rating. For extension cord lengthsup to 75 feet, youmust usea cord with a

AWGrating of atleast14; for longerlengths, theAWGrating must be12. Donot use morethan 175

feetofextensioncord.

Alwaysinspectextension cords foranydamage. If there areanyloose, frayed orexposedwires,

damagedinsulation,ordefectiveconnections,replacethecord.

HarborFreightToolscan supply ULlisted and outdoor rated cordsinmultipleAWGratingsifneeded.

UNPACKING

Makesureyourtoolhas come complete with all accessories. Your package should includethegrinder,

reversiblesidehandle, steel wheelguard,one wrench and areplacement set of carbonbrushes. Ifa

pieceismissingcontactHarborFreightToolsCustomerSatisfactionatthenumberonthecoverofthis

manual.

OPERATIONS

SelectingWheels:

1.Make sure the wheel you select is rated for at least 8000 RPM.

2.Usesiliconcarbidegrindingwheelsforconcreteandstone.

3.Usealuminumoxide wheelsforferrousmetals. REV02/04