Chatsworth Products FIBER SEGREGATION KIT User manual

FIBER SEGREGATION KIT

IIS-735475, 02/29/08, Rev. 1, CPI/J Garza

800-834-4969 • techsupport@chatsworth.com • www.chatsworth.com

This drawing contains proprietary and confidential information and is protected by U.S. and international law.

Unauthorized reproduction, disclosure or use of the drawing or the information therein is expressly forbidden

except as agreed to in writing by Chatsworth Products, Inc.

Page 1 of 3

Installation Instructions

Verification

The Fiber Segregation Kit is for use with the Evolution™Vertical Cable Managers

in the following configurations:

The number of kits per manager depends on the position of the Movable Mid-

Section in Evolution g2 double-sided managers and the width of the vertical cable

manager as listed in the table below:

Cable

Manager

Width

Single-Sided or

Double-Sided with

50/50 Front/Rear Split

Double-Sided with

60/40 Front/Rear

Split

6” (150 mm) 0 1

10” (250 mm) 1 2

12” (300 mm) 2 2

Verify Mid-Section Locations

In order for the Fiber Segregation Kit to mount to the Accessory Panel on the

Single Sided Evolution g1 or the Moveable Mid-Section on the Double Sided

Evolution g2, the distance between the panels must be 18.6 inches.

Fiber Segregation Kit

18.6”

FIBER SEGREGATION KIT

Page 2 of 3

Installation Instructions

Tools Required

#3 Phillips Screw Driver

Intended Use

The Fiber Segregation Kit creates a separate pathway for fiber cables and patch

cords inside Evolution™Vertical Cable Managers.

Included Hardware

•Qty 5 ea – Taptite Screws, 10-32 x 1/2”

•Qty 2 ea – Fiber Segregation Spool Assembly

•Qty 2 ea – Extension Panel

Packaged Hardware

Fiber Se

ation S

ool Assembl

** Extension Panel

** The Extension Panel is required when mounting to the Single

Sided Evolution g1 or Double Sided Evolution g2 with Moveable

Mid-Sections in the center position.

10-32 x ½” Ta

tite Screw

FIBER SEGREGATION KIT

Page 3 of 3

Installation Instructions

Fastening Fiber Segregation Kit

NOTE: For easier installation, attach Fiber Segregation Kit before installing

optional Cable Spool Kit provided with Vertical Cable Manager.

Installation

1. Fiber Segregation Kits ship with all necessary hardware included.

2. Locate the included hardware to verify contents.

3. Mount a single assembly using two 10-32 x ½” screws.

4. For installing to a Double Sided Evolution g2 with Mid-Sections located in

the rear position:

a. Insert the 10-32 screws through the slots in the Fiber

Segregation Bracket closest to the indexing spool as shown in

Figure 1.

b. Attach the assembly using the second mounting holes in the Mid-

Section from the side panels as shown in Figure 1. Edge of

bracket should nearly touch side panel.

5. For installing to a Single Sided Evolution g1 or Double Sided Evolution g2

with Mid-Sections located in the center position:

a. Insert the 10-32 screws through the slots in the Extension Panel

as shown in Figure 2.

b. Attach the Extension Panel to the slots farthest away from the

indexing spool in the Fiber Segregation Assembly.

c. Attach the entire assembly using the second mounting holes in

the Mid-Section from the side panels as shown in Figure 2.

6. The Fiber Segregation Spools turn 360° with stops at 90° allowing easy

access to fiber cables.

FIGURE 1 FIGURE 2

10-32

Taptite

Screw

Extension Panel

Other Chatsworth Products Cable Box manuals

Chatsworth Products

Chatsworth Products Evolution User manual

Popular Cable Box manuals by other brands

FBS

FBS C01 installation instructions

peerless-AV

peerless-AV IBA2 Installation and assembly

Extron electronics

Extron electronics Cable Cubby 1202 installation guide

peerless-AV

peerless-AV IBA3AC Installation and assembly

Channel Vision

Channel Vision AFFINITY P-0328 instructions

Minebea Intec

Minebea Intec IE11357 operating instructions

StarTech.com

StarTech.com BOX4CABLE manual

Commercial Electric

Commercial Electric 5053-WH installation guide

Motorola

Motorola DCT6412 DUAL-TUNER DVR AND HD SET-TOP - MICROSOFT... User's reference manual

Renkforce

Renkforce 1395556 operating instructions

Huawei

Huawei FAT9102SD-32G Quick installation guide

VISSEM Electronics

VISSEM Electronics Opticube VSOF-OTB-E manual

Beta

Beta 1844 15-H05/SCK Instructions for use

FSR

FSR FL-1550 installation instructions

Renkforce

Renkforce 1674559 operating instructions

Minebea Intec

Minebea Intec PR 6130/64Sa installation manual

KS Tools

KS Tools efuturo Wallbox operating instructions

Minebea Intec

Minebea Intec Weighbridge PR 6021/68S installation manual