Chapin 97361 User manual

See website for warranty details

Use and Care Manual

DO NOT RETURN TO STORE

Call: 1-800-950-4458

www.chapinmfg.com

Chapin International, Inc

P.O. Box 549 700 Ellicott St.

Batavia, NY 14021-0549 U.S.A.

1-800-950-4458 www.chapinmfg.com

Model 97361, 97561

016028 R0121

Carefully Read These Instructions Before Use

WARNING

25 Gallon

15 Gallon

ATV SPRAYER

WARNING

IMPROPER USE OR FAILURE TO FOLLOW INSTRUCTIONS CAN RESULT IN

EXPLOSIVE FAILURE CAUSING SERIOUS EYE OR OTHER INJURY.

FOR SAFE USE OF THIS PRODUCT YOU MUST READ AND FOLLOW ALL

INSTRUCTIONS. DO NOT LEAVE SPRAYER IN THE HOT SUN. HEAT CAN CAUSE

PRESSURE BUILD-UP RESULTING IN POSSIBLE EXPLOSION. DO NOT STORE OR

LEAVE SOLUTION IN TANK AFTER USE. ALWAYS WEAR GOGGLES, GLOVES, LONG

SLEEVE SHIRT, LONG PANTS AND FULL FOOT PROTECTION WHEN SPRAYING.

DO NOT ATTEMPT TO MODIFY THIS SPRAYER. REPLACE PARTS ONLY WITH

MANUFACTURER’S ORIGINAL PARTS.

NEVER SPRAY FLAMMABLE, CAUSTIC, ACIDIC, CHLORINE, BLEACH,

PETROLEUM BASED OR OTHER CORROSIVE SOLUTIONS OR HEAT, PRESSURE,

OR GAS PRODUCING CHEMICALS. ALWAYS READ AND FOLLOW CHEMICAL

MANUFACTURER’S INSTRUCTIONS BEFORE USE WITH THIS SPRAYER AS

SOME CHEMICALS MAY BE HAZARDOUS WHEN USED WITH THIS SPRAYER.

ENSURE THE WIRING HARNESS DOES NOT BECOME PINCHED OR DAMAGED

IN ANY WAY. THIS MAY DAMAGE THE PUMP OR CAUSE THE WIRING

HARNESS TO OVERHEAT, RESULTING IN MELT DOWN OR FIRE.

SOME CHEMICALS WILL DAMAGE THE PUMP VALVES IF ALLOWED

TO SOAK UNTREATED FOR A LONG PERIOD OF TIME. ALWAYS FLUSH

THE PUMP WITH WATER AFTER USE. DO NOT ALLOW CHEMICALS

TO SIT IN PUMP FOR EXTENDED TIMES OF IDLENESS. FOLLOW

CHEMICAL MANUFACTURERS INSTRUCTIONS ON DISPOSAL OF ALL

WASTE WATER FROM THE SPRAYER.

USE WATER BASED CHEMICALS ONLY.

CAUTION

THIS SPRAYER HAS BEEN DESIGNED TO BE ATTACHED TO STABLE SURFACES.

Chapin Spot Sprayer Operator’s Manual - English

CONTENTS- NOT TO SCALE

H-1

Phillips Head Screw

C-3

External Bypass

H-3

Worm Gear Clamp

H-7

Lead Wire Assembly

H-5

Drain Cap w/ Lanyard

H-6

Loop Clamp

C-1

Wand Assembly

H-2

Phillips Head

Screw

H-4

Wand Clamp

SPRAYER HARDWARE

SPRAYER COMPONENTS

C-2

Pump

C-4

Flow Director Valve

NOTE: not all components shown may be needed on your model.

Chapin Spot Sprayer Operator’s Manual - English

ASSEMBLE PUMP TO TANK

Using H-1 screws, fasten pump (C-2) to face plate with loop clamp (H-6) inserted between

pump and front left screw. NOTE: Do not over-tighten screws.

INSTALL EXTERNAL BYPASS AND FLOW DIRECTOR VALVE

Install external bypass (C-3) and ﬂow director valve (C-4) into pump quick release ports;

engage quick release locks. Note: to ensure a good seal, a tight ﬁt is used; signiﬁcant hand

force may be necessary to install bypass ﬁttings.

H-1

H-6

C-2

C-4

C-3

Quick Release Locks

(open/close) Assembled

Chapin Spot Sprayer Operator’s Manual - English

INSTALL WAND CLIPS

Install wand clip (H-4) and wand clip from nylon strap (as shown above) with screws (H-2).

Note: The wand clip shown to the right can be found hanging from the nylon strap.

Guide wand hose (C-1) through loop clamp (H-6) and attach hose (C-1) to diverting valve

(C-4) with hose clamp (H-3). Tighten clamp (H-3).

C-1

H-6 H-6

ATTACH HOSE TO DIVERTING VALVE

C-1 H-3 C-4

H-2

H-4

Chapin Spot Sprayer Operator’s Manual - English

WAND ASSEMBLY

Wand O-ring Shut-O Valve

Retaining Nut

Make sure the o-ring is installed on the end of the wand. Insert the wand into shut-off valve.

Turn and tighten the retaining nut clock-wise onto the shut-off valve.

ATTACH CHEMICAL CONCENTRATE TANK

Before chemical tank installation, attach supplied rachet straps to strap slots on tank.

Securely fasten assembly to ATV. NOTE: not all models included ratchet straps.

Attach the mix valve’s suction tubing (1) to the chemical concentrate tank’s quick release

port (2). Secure chemical concentrate tank with nylon webbing (3).

Assembled

INSTALL DRAIN CAP

Install cap lanyard around drain plug. Screw drain cap (H-5) on drain plug.

H-5

Chapin Spot Sprayer Operator’s Manual - English

SPRAYER COMPONENTS

MIX SETTING VALVE

The mix setting valve allows the user to

set the desired chemical mix ratio. It is

calibrated to a speciﬁc gravity of water.

See setting chart for each settings mix

value in oz./gal. Due to chemical viscosity,

actual mix ratios may vary. Refer to

chemical’s recommended mix ratios

when choosing what setting to use.

Note:

• Use water based chemicals only.

• When not spraying set mix ratio to zero.

WAND / BOOM SELECTOR VALVE

The wand/boom selector valve allows the user to select the ﬂow to either be diverted to

the wand assembly or the boom.

BYPASS / PRESSURE VALVE

The bypass/pressure valve allows the user to adjust the wand’s pressure. During low ﬂow

applications it allows ﬂow to be diverted to eliminate pump cycling.

How to use: Start with the valve set to “Bypass off”. When the pump begins to cycle;

between on and off, turn the valve slowly counter clockwise until the cycling stops. The

valve setting should fall in the “optimal” ﬂow region.

Note:

• If the bypass is used beyond the “optimal ﬂow” region the pump may not shut off as

the bypass doesn’t allow it to build enough pressure to turn the pump off.

• If too much air is introduced into the system from changing chemicals or running the

water or chemical tanks dry it may be necessary to switch the bypass valve to “Bypass

off/Prime” in order to prime the unit.

CHEMICAL CONCENTRATE TANK

The chemical concentrate tank is where the chemical concentrate is held. To install the

tank, insert the tank onto the faceplate’s alignment feet and secure with the nylon webbing

and snap latch.

CHEMICAL TANK QUICK RELEASE COUPLING

The chemical tank quick release coupling allows the user to quickly and cleanly change

out chemical tanks. When disengaged the tank’s quick release automatically closes to

stop spillage. To use, align the male locking pins with the female nut’s slots. Press female

nut over the male nut and turn clockwise to lock in place. To disengage the quick release

coupling, slightly push the female nut in, turn counterclockwise and remove.

Chapin Spot Sprayer Operator’s Manual - English

OPERATING INSTRUCTIONS

1. Fill both water and chemical tanks.

2. Set Mix Ratio Valve to “0” (1) by turning the adjustment wheel.

3. Set Wand/Boom selector valve to “Wand” (2).

4. Set Bypass to “Bypass Off/Prime” (3) by turning the selector knob.

5. Turn system on by pressing wiring harness in-line switch to “on” (not shown).

6. Prime: using the wand spray until all air has been purged from the system. If the

bypass was set to “off” the pump will begin to cycle on and off.

7. Adjust bypass until the pump stops cycling. Do not bypass more than needed as this

will cause the pump to continuously run.

8. Set the desired mix ratio setting and begin spraying.

9. Cleaning between chemical types: While spraying on mix setting 7 disconnect the

concentrate tank’s quick release. This allows chemical in the line to quickly be ﬂushed.

If necessary, ﬂush with water by submerging the chemical line into the water source.

Once adequately ﬂushed the new concentrate tank may be installed. With the mix

valve set to 7 and the bypass set to “Bypass off/Prime” prime the system. Once

primed, re-adjust the bypass valve and you’re ready to spray.

CAUTION

ALWAYS FOLLOW CHEMICAL MANUFACTURER’S INSTRUCTIONS FOR

PROPER USE, STORAGE AND DISPOSAL.

ALWAYS FOLLOW STATE/LOCAL CODES FOR PROPER HANDLING,

STORAGE AND DISPOSAL OF CHEMICAL.

SETTING GUIDE

SETTING OUNCE PER

GALLON

0 0 oz/gal

1 1 oz/gal

2 2 oz/gal

3 3 oz/gal

4 4 oz/gal

5 5 oz/gal

6 10 oz/gal

7 15 oz/gal

Chemical mix ratios can easily be adjusted in

between or lower than the listed 0-7 settings by

pre-diluting your concentrate.

For example, if you wish to spray at .5 oz/gal, simply

mix your chemical 50:50 with clean water before

placing it in the concentrate tank.

Divide the desired rate by the closest higher rate

(oz. /gal) value from above guide to determine the %

of chemical in concentrate tank.

Desired Rate (oz./gal)

Closest higher rate (oz./gal)

100

% Chemical

to Water for

Concentrate

Tank

Chapin Spot Sprayer Operator’s Manual - English

TROUBLESHOOTING

CONDITION CHECK

Pump won’t start Correct voltage (±10%) and electrical connections

Fuse or breaker

Pressure switch operation

Rectifer or motor for open or grounded circuit

Locked drive assembly

Correct voltage at switch

Pump will not prime

(No discharge with motor

running)

Debris in strainer

Restriction (kinks) in inlet / outlet tubes

Debris / swelling in inlet / outlet valves

Bypass is not in “off” position

Pump will not shut-off

(output line closed and

no leaks)

Air trapped in outlet line or pump head

Correct voltage to pump

Debris in pump inlet / outlet valves

Loose drive assembly or pump head screws

Pressure switch operations / adjustments

Leaks from pump head

or switch

Loose screws at switch or pump head

Switch diaphragm ruptured or pinched

Punctured diaphragm if ﬂuid is present

Pump output spits and

sputters

All hose clamps are adequately tight

No holes in tubing

There is adequate liquid in both the water and chemical tank

Adjust external bypass to optimize spray pattern

Pump makes noise, but

no output

Prime with garden hose by removing intake hose and ﬂood with

water while pump is running until water starts ﬂowing (this may

take up to 15 minutes to create suction).

To better understand the priming process see video at: https://www.

youtube.com/watch?v=lrNeAvNL7Fs or search “Priming the Pump on Your

Chapin ATV Sprayer” at Chapin International’s YouTube page.

Chapin Spot Sprayer Operator’s Manual - English

BREAKDOWN & PARTS LIST

REF NO. PART NO. QTY DESCRIPTION

1 6-9138 1 Pump Assembly, 2.5 GPM

2 6-9202 1 Pump Hardware Kit

3 6-8060 1 Tank Assembly, 1.33 Gallon

3 6-8061 1 Tank Assembly, 2.0 Gallon

46-8272 1 Faceplate, 15 Gallon

46-8273 1 Faceplate, 25 Gallon

5 6-8219 1 Extension Assembly

6 6-8138 1 Shut-Off Assembly, cushion grip

7 6-8093 1 Nozzle Kit, Poly

8 6-9203 1 Suction Hose Assembly

9 6-8321 1 Inlet Strainer

10 6-8146-1 1 Tank Lid & 6 inch Filter Basket

11 6-8325 1 Drain Plug Kit

12 6-8003 2 Worm Gear Clamp

13 6-9204 1 Rubber Grommet

14 6-8324 2 Wand Clip, pair

15 6-8274 1 Wand Clip, Tie Down

16 6-8320 1 Lead Wire Assembly w/ Switch

17 6-9205 1 15’ Hose, Reinforced

To Order Replacement Parts: 1-800-950-4458

This manual suits for next models

Table of contents

Languages:

Other Chapin Paint Sprayer manuals

Chapin

Chapin 75009 User manual

Chapin

Chapin 31430 User manual

Chapin

Chapin Tree/TurfPro 61900 User manual

Chapin

Chapin 97500B Parts list manual

Chapin

Chapin 22251XP User manual

Chapin

Chapin 97400 Parts list manual

Chapin

Chapin 61813 User manual

Chapin

Chapin PROSERIES Series User manual

Chapin

Chapin Sk-1154-1 User manual

Chapin

Chapin 60100 User manual

Chapin

Chapin 97300 Installation instructions

Chapin

Chapin EZ MOUNT 97200E User manual

Chapin

Chapin ProSeries 63800 User manual

Chapin

Chapin 61813 User manual

Chapin

Chapin EZ MOUNT 97300E User manual

Chapin

Chapin BLEACH & DISINFECTANT 61575 User manual

Chapin

Chapin MIXES 63950 User manual

Chapin

Chapin 97500 Parts list manual

Chapin

Chapin 63924 User manual

Chapin

Chapin G362 Product manual

Chapin

Chapin Sk-1169-1 User manual

Chapin

Chapin EZ MOUNT 97024 User manual

Chapin

Chapin 60124 User manual

Chapin

Chapin G362D User manual

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Graco

Graco 246737 Repair and parts

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

Graco

Graco EM 390 Instructions-parts list

DeVilbiss

DeVilbiss LUNA2i Operation manual