Chamberlain 940EV User manual
Wireless Keyless Entry
MODELS 940EV, 940EV-P2, 940EVC, AND 940EVC-P2
Introduction ............. 2
Programming ...........3-6
Program PIN .................3
Change an Existing PIN..........4
Program a Temporary PIN -
Number of Hours ..............5
Program a Temporary PIN -
Number of Openings............6
Installation.............. 7
Operation............... 8
FAQs .................. 9
2
To prevent possible SERIOUS INJURY or DEATH from a moving gate
or garage door:
• Install Keyless Entry Control within sight of garage door, out of reach
of small children at a minimum height of 5 feet (1.5 m) above floors,
landings, steps or any other adjacent walking surface, and away from
ALL moving parts of door.
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote controls.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
For use with Chamberlain garage door openers manufactured after
January 1, 1993. The garage door opener activates when the 4-digit
Personal Identification Number (PIN) and ENTER button are pressed on
the Keyless Entry.
Install the battery and program the Keyless Entry prior to installation.
Make sure the garage door opener has a working light bulb because it
is a programming indicator.
Introduction
GETTING STARTED
Locate the Learn button on the garage door opener. NOTE: Your garage door opener may look different.
Learn
LED
Learn
LED
OR OR Learn
LED
Red/Orange Purple Yellow
Learn
LED
Green
OR
WARNING: This product can expose you to chemicals including
lead, which are known to the State of California to cause cancer or
birth defects or other reproductive harm. For more information go
to www.P65Warnings.ca.gov
3
PROGRAM PIN
To program the Keyless Entry to more than one garage door opener,
repeat the programming steps using a new PIN for each additional
garage door opener.
Press and hold the *and #buttons until the
lights on the keypad stop blinking.
Click
Click
Click
Click
GARAGE DOOR OPENER TYPE # OF
PRESSES
Yellow Learn Button (315 and 390 MHz Security+ 2.0®) 1
Purple Learn Button (315 MHz Security+®) 2
Red/Orange Learn Button (390 MHz Security+®) 3
Green Learn Button (390 MHz Billion Code) 4
Enter a 4-digit personal identification
number (PIN) of your choice, then press
the ENTER button.
Press and release the ENTER button on the
Keyless Entry the number of times that
corresponds with your garage door opener
type:
Press and release the 0button.
Click
Click
Press and release the Learn button on the
garage door opener. The Learn LED will
light.
Within 30 seconds...
Click
Click
Enter your 4-digit PIN, then
press and release the
ENTER button until the
garage door opener lights
flash or two clicks are
heard.
Click
Click
To test, enter your PIN,
then press the ENTER
button. The garage door
opener will activate.
1
Click
Click
Programming
2
Click
Click
3
4
5
6
7
4
CHANGE AN EXISTING PIN
Programming
Click
Click
Enter the programmed PIN that you want
to change.
1
Press and hold the #
button until the light bulb
on the garage door opener
blinks twice.
2
x2
Enter the new 4-digit PIN
of your choice, then press
the ENTER button. The
light bulb on the garage
door opener will blink
once.
3
x2
To test, enter the new PIN,
then press the ENTER
button. The garage door
opener will activate.
4
Click
Click
5
PROGRAM A TEMPORARY PIN - NUMBER OF HOURS
Programming
Enter any programmed
PIN, then press and hold
the button until the garage
door opener light bulb
flashes 3 times.
1
NOTE: This feature is not available on garage door openers that have a green Learn button or an external receiver.
A temporary 4-digit PIN can be programmed to allow access to visitors. Each programmed PIN can program one temporary PIN. The temporary PIN
can be set for a number of hours or a number of door openings. The temporary PIN cannot be the same as any previously programmed PIN.
Enter the temporary 4-digit
PIN of your choice, then
press the ENTER button.
The garage door opener
light bulb will flash 4
times.
x3
x4
Press the number of
hours the temporary PIN
will work (up to 255).
Then press the *button.
The garage door opener
light bulb will flash once.
3
x3 x4
To test, press the
temporary PIN, then press
the ENTER button. The
garage door opener will
activate.
4
x3
x4
Click
Click
6
PROGRAM A TEMPORARY PIN - NUMBER OF OPENINGS
Programming
Enter any programmed
PIN, then press and hold
the *button until the
garage door opener light
bulb flashes 3 times.
1
NOTE: This feature is not available on garage door openers that have a green Learn button or an external receiver.
A temporary 4-digit PIN can be programmed to allow access to visitors. Each programmed PIN can program one temporary PIN. The temporary PIN
can be set for a number of hours or a number of door openings. The temporary PIN cannot be the same as any previously programmed PIN.
Enter the temporary 4-digit
PIN of your choice, then
press the ENTER button.
The garage door opener
light bulb will flash 4
times.
2
x3
x4
3Press the number of
openings the temporary
PIN will work (up to 255).
Then press the #button.
The garage door opener
light bulb will flash once.
To test, press the
temporary PIN, then press
the ENTER button. The
garage door opener will
activate. If the temporary
PIN was set for a number
of openings, the test will
use up one opening.
4
x3 x4
x3
x4
Click
Click
7
Select a location to mount the Keyless Entry at a minimum height
of 5 feet (1.5 m) out of reach of children.
Remove battery cover and battery.
Mark the top mounting hole and drill 1/8 inch (3.2 mm) pilot hole.
Install the top screw, allowing 1/8 inch (3.2 mm) to protrude above
the surface. Position the Keyless Entry over the top screw.
Mark the bottom hole and drill 1/8 inch (3.2 mm) pilot hole. Install
the bottom screw. Do not overtighten to avoid cracking the plastic
housing.
Reinstall battery and replace cover.
Installation
1
2
3
4
5
6
8
To deactivate the one button close feature:
Press and hold the 1 and 9 buttons for 10 seconds.
The keypad will blink four times when the one
button close feature is deactivated.
To activate the one button close feature:
Press and hold the 1 and 9 buttons for 10 seconds.
The keypad will blink twice when the one button
close feature is activated.
The Keyless Entry has a feature
that allows the door to be closed
using the ENTER button instead
of a PIN.
NOTE: This feature is not
available on garage door
openers manufactured prior to
2006 or an external receiver.
The garage door opener activates when the PIN and ENTER button are
pressed. The keypad will blink for 15 seconds, during that time the
ENTER button can be used to stop, start or reverse the door.
If the wrong number is accidentally pressed, press the correct PIN then
the ENTER button. The Keyless Entry will transmit only the last four
digits that were pressed before the ENTER button.
Operation
ONE BUTTON CLOSE Replace the battery when the keypad becomes dim or does not light
after a button is pressed.
Dispose of old battery properly.
9V Battery
BATTERY
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
9
FAQs
Why won’t my keypad work?
•Did the keypad lights come on when you entered your PIN? If the
keypad lights do not turn on when you press a button, it indicates
that the battery needs to be replaced. Replace with a 9V battery.
•Try reprogramming the Keyless Entry to the garage door opener.
•Make sure the Keyless Entry is compatible with your garage door
opener (Chamberlain garage door openers manufactured after
January 1, 1993).
•If the solutions above did not work, replace the Keyless Entry.
How many PINs can I program to the Keyless Entry?
The Keyless Entry will program up to 24 PINs and up to 24 temporary
PINs.
Can I use the same PIN to activate multiple garage doors?
No, you cannot use the same PIN number twice. The Keyless Entry will
overwrite the original programming if the PIN is programmed a second
time.
Why don’t the keypad lights turn on when I press a button?
If the keypad lights do not turn on when you press a button, it indicates
that the battery needs to be replaced. Replace with a 9V battery.
What garage door openers are compatible with the Keyless Entry?
The Keyless Entry is only compatible with Chamberlain garage door
openers manufactured after January 1, 1993.
Why does the door close when I just press the ENTER button?
The Keyless Entry has a “One Button Close” feature that allows the door
to be closed using the ENTER button instead of a PIN. If you do not
want this feature activated, press and hold the 1 and 9 buttons for 10
seconds. The keypad will blink four times when the one button close
feature is deactivated.
What if I enter the wrong PIN?
If the wrong number is accidentally pressed, press the correct PIN then
the ENTER button. The Keyless Entry will transmit only the last four
digits that were pressed before the ENTER button.
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
WARRANTY
ONE YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. warrants to the first consumer purchaser
of this product that it is free from defect in materials and/or
workmanship for a period of 1 year from the date of purchase.
REPLACEMENT PARTS
Battery ..............................................10A25
Keypad Cover........................................41D621
Battery Cover ........................................41D541
www.chamberlain.com
© 2017, The Chamberlain Group, Inc.
All Rights Reserved
114A5071
Other manuals for 940EV
1
This manual suits for next models
3
Table of contents
Languages:
Other Chamberlain Remote Starter manuals
Chamberlain
Chamberlain 877MAX User manual
Chamberlain
Chamberlain LiftMaster Professional 387LM User manual
Chamberlain
Chamberlain Security+ 377LG User manual
Chamberlain
Chamberlain 940CD-01 User manual
Chamberlain
Chamberlain 976LM Security+ User manual
Chamberlain
Chamberlain Series 740 User manual
Chamberlain
Chamberlain Security+ 940CD User manual
Chamberlain
Chamberlain LiftMaster Professional Security+ 376LM User manual
Chamberlain
Chamberlain LiftMaster 466LM User manual
Chamberlain
Chamberlain LiftMaster Securty+ 976LM User manual
Chamberlain
Chamberlain 727E Series User manual
Chamberlain
Chamberlain 40 User manual
Chamberlain
Chamberlain 940EV-P2 User manual
Chamberlain
Chamberlain Merlin E840M User manual
Chamberlain
Chamberlain Clicker KLIK2U User manual
Chamberlain
Chamberlain 877MAX User manual
Chamberlain
Chamberlain LiftMaster TAC1 Assembly instructions
Chamberlain
Chamberlain 878MAX User manual
Chamberlain
Chamberlain 940C Security+ User manual
Chamberlain
Chamberlain 940D-01 Guide
