Chamberlain HD220 User manual

The Chamberlain Group, Inc.

845 Larch Avenue

Elmhurst, Illinois 60126-1196

www.chamberlain.com

CONTENTS

Preparation .............................. 1-4

Assembly................................. 5-9

Installation............................ 10-17

Install the Door Control ............. 18-19

Install the Protector System®...... 20-23

Power.................................. 24-25

Adjustments .......................... 26-28

Operation.................................. 29

Features................................... 30

Remote Control .......................... 31

To Erase the Memory.................... 32

To Open the Door Manually ............ 32

Maintenance.............................. 33

Diagnostic Chart ......................... 34

Warranty .................................. 35

Chain Drive

Garage Door Opener

■ Please read this manual and the enclosed safety materials carefully!

■Fasten the manual near the garage door after installation.

■ The door WILL NOT CLOSE unless the Protector System®is connected and

properly aligned.

■Periodic checks of the garage door opener are required to ensure safe operation.

■The model number label is located on the back panel of your garage door opener.

■This garage door opener is compatible with Security✚2.0™ accessories.

Serial Number:

Date of Purchase:

Model Number:

Models HD220, HD220C,

PD220, PD222, LW260C,

and LW2200

FOR RESIDENTIAL USE ONLY

INSTALL ON 7 FOOT

SECTIONAL DOORS ONLY

www.prodregister.com/chamberlain or

scan the QR code with your smartphone

Write down the following information

for future reference:

Safety Symbol and Signal Word Review

This garage door opener has been designed and tested to offer safe service provided it is installed,

operated, maintained and tested in strictaccordance with the instructions and warnings contained in this

manual.

When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the

possibility of serious injury or death if you do not comply with the warnings that accompany them. The

hazard may come from something mechanical or from electric shock.Read the warnings carefully.

Mechanical

Electrical

When you see this Signal Word on the following pages, it will alert you to the possibility of damage to

your garage door and/or the garage door opener if you do notcomply with the cautionary statements that

accompany it. Read them carefully.

Check the Door

To prevent possible SERIOUS INJURY or DEATH:

lALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance.

An unbalanced garage door may NOT reverse when required.

lNEVER try to loosen, move or adjust garage door, door springs, cables, pulleys, brackets or their

hardware, ALL of which are under EXTREME tension.

lDisable ALL locks and remove ALL ropes connected to garage door BEFORE installation and

operating garage door opener to avoid entanglement.

To prevent damage to garage door and opener:

lALWAYS disable locks BEFORE installing and operating the opener.

lONLY operate garage door opener at 120 V, 60 Hz to avoid malfunction and damage.

1. Disable locks and remove any ropes connected to the garage door.

2. Lift the door halfway up. Release the door. If balanced, it should stay in

place, supported entirely by its springs.

3. Raise and lower the door to check for binding or sticking. If your door

binds, sticks, or is out of balance, call a trained door systems

technician.

4. Check the seal on the bottom of the door. Any gap between the floor

and the bottom of the door must not exceed 1/4 inch (6 mm).

Otherwise, the safety reversal system may not work properly.

5. The opener should be installed above the center of the door. If there is

a torsion spring or center bearing plate in the way of the header

bracket, it may be installed within 4 feet (1.2 m) to the left or right of the

door center. See page 11.

Torsion

Spring

Extension

Spring

Preparation

Additional Items You May Need:

Survey your garage area to see if you will need any of the following items:

n(2) 2X4 PIECES OF WOOD

May be used to fasten the header bracket to the structural supports. Also used to position the

garage door opener during installation and for testing the safety reversing sensors.

nSUPPORT BRACKET AND FASTENING HARDWARE

Must be used if you have a finished ceiling in your garage.

nEXTENSION BRACKETS (MODEL 41A5281) OR WOOD BLOCKS

Depending upon garage construction, extension brackets or wood blocks may be needed to

install the safety reversing sensor.

nFASTENING HARDWARE

Alternate floor mounting of the safety reversing sensor will require hardware not provided.

nOUTSIDEQUICKRELEASE (MODEL 7702C)

Required for a garage with NO access door.

nDOOR REINFORCEMENT

Required if you have a lightweight steel, aluminum, fiberglass or glass panel door.

Tools Needed

3/16

7/16

1/2

7/32

5/16

3/8 7/16

1/2

Preparation

Carton Inventory/Repair Parts

Your garage door opener is packaged in one carton which contains the motor unit and all parts

illustrated below. Accessories vary depending on the garage door opener model purchased. Depending

on your model, other accessories may be included with your garage door opener. Instructions for these

accessories will be attached to the accessory and are not included in this manual. If anything is missing,

carefully check the packing material. Hardware for assembly and installation is shown on the next page.

Save the carton and packing material until the installation and adjustment is complete. The images

throughout this manual are for reference only and your productmay look different.

Key Description Part #

AHeader bracket 41A5047-1

BPulley (In hardware bag)

CDoor bracket 41A5047

DCurved door arm

EStraight door arm (Packaged inside front rail section)

FTrolley NOTE: Be sure to assemble the trolley before sliding onto rail. 41C5141-1

GEmergency release rope and handle (In hardware bag)

HRail (1 front and 4 center sections)

IHanging brackets (2) (Packaged inside the front rail section)

JGarage door opener (motor unit)

KChain spreader (In hardware bag)

LChain and cable

MDoor control 041A7367-3

NRemote control 950ESTD

OThe Protector System®Safety reversing sensors with 2 conductor white and white/black

wire attached: Sending Sensor (1), Receiving Sensor (1), and Safety Sensor Brackets (2) 41A5034

NOT SHOWN

White and red/white wire 41B4494-1

Owner's manual 114A4706

Preparation

Hardware Inventory

Bolt

1/4"-20x2"

Lock Nut 1/4"-20

Lock Nut 1/4"-20 (4)

Self-Threading

Screw

1/4"-20x1-3/4" (2)

Master Link

Clevis Pin 5/16"x1-1/2"

Clevis Pin

5/16"x1-1/2"

Ring Fastener (4)

Hex Bolt 1/4"-20x3/4" (4)

Lock Washer 5/16"

Hex Nuts 5/16" (2) Self-Threading Screw

1/4"-14x5/8" (2)

Clevis Pin 5/16"x1"

Clevis Pin 5/16"x1-1/4"

Carriage Bolt

1/4"-20x1/2" (2)

Wing Nut 1/4"-20 (2)

ASSEMBLY HARDWARE INSTALLATION HARDWARE

Screw 6ABx1" (2)

DOOR CONTROL HARDWARE

Lag Screw 5/16"-9x1-5/8" (2) Lag Screw #14-10x1-1/2" (2)

Threaded

Shaft

Spacer

Preparation

Assembly

STEP 1 Assemble the rail and trolley

To prevent INJURY from pinching, keep hands and fingers away from the joints while assembling the

rail.

To avoid installation difficulties, do not run the garage dooropener until instructed to do so.

The front rail has a cut out “window” at the door end (see illustration). The front rail has a rail tab. This tab

MUST be on the top of the rail when assembled.

1. Remove the straight door arm and hanging bracket packaged inside the front rail and set aside

for Installation Step 5 and 9. NOTE: To prevent INJURY while unpacking the rail carefully remove

the straight door arm stored within the rail section.

2. The rail sections have a groove on the sides near the bottom edge. Use these grooves to align

the rail sections. Slide the tapered ends into the larger ones. Tabs along the side will lock into

place.

3. Place the motor unit on packing material to protect the cover, and rest the back end of the rail on

top. For convenience, put a support under the front end of the rail.

4. As a temporary stop, insert a screwdriver into the hole 10" (25 cm) from the front end of the rail,

as shown.

5. Check to be sure there are 4 plastic wear pads inside the inner trolley. If they became loose

during shipping, check all packing material. Snap them back into position as shown.

6. Slide the trolley assembly toward the screwdriver as shown.

7. Slide the chain spreader onto the rail until it stops.

Inner Trolley

Wear Pads

Front Rail

Section

(TO DOOR)

To garage

door opener

(TO MOTOR UNIT)

SLIDE CHAIN

SPREADER

ONTO RAIL

Rail

Tab

Trolley

Window

Cut-Out

Idler

Pulley

Hole

Chain

Spreader

Outer Trolley

Alignment

Groove

Alignment

Groove

Assembly

STEP 2 Fasten the rail to the motor unit

To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the

top of the opener.

1. Ensure that the chain spreader is installed. Insert a 1/4"-20x2" bolt and spacer into the cover

protection bolt hole on the back end of the rail as shown. Tighten securely with a 1/4"-20 lock nut.

DO NOT overtighten.

2. Use the carton to support the front end of the rail.

3. Place the rail onto the motor unit. Align the screw holes in the rail with the holes on top of the

motor unit.

4. Fasten the rail with the screws; DO NOT use any power tools. The use of power tools may

permanently damage the garage door opener.

HARDWARE

Bolt 1/4"-20x2"

Lock Nut 1/4"-20

Spacer

Self-Threading Screw

1/4"-20x1-3/4"

Cover Protection

Bolt Hole

Spacer

Bolt 1/4"-20x2"

Lock Nut 1/4"-20

Self-Threading Screws

1/4"-20x1-3/4"

Assembly

STEP 3 Install the pulley

1. Lay the chain/cable beside the rail, as shown. Grasp the end with the cable loop and pass

approximately 12" (30 cm) of cable through the window. Allow it to hang until Assembly Step 4.

2. Remove the tape from the idler pulley. The inside center should be pre-greased. If dry, regrease

to ensure proper operation.

3. Place the idler pulley into the window as shown.

4. Secure idler pulley with clevis pin and ring fastener.

5. Rotate the pulley to be sure it spins freely.

6. Locate the rail tab. The rail tab is between the idler bolt and the trolley in the front rail section. Use

a flat head screwdriver and lift the rail tab until the tab is vertical (90º).

HARDWARE

Clevis Pin 5/16"x1-1/2" Ring Fastener

Screwdriver

Rail

Idler Pulley

Grease Inside Pulley

Cevis Pin

5/16"x

1-1/2"

Ring Fastener

Rail Tab

Chain/Cable

CORRECT

INCORRECT

Rail Tab

Assembly

STEP 4 Install the chain

To avoid possible SERIOUS INJURY to finger from moving garage door opener:

lALWAYS keep hand clear of sprocket while operating opener.

lSecurely attach chain spreader BEFORE operating.

1. Pull the cable around the idler pulley and toward the trolley.

2. Connect the cable to the retaining slot on the trolley. (a)

a. Push pins of master link bar through cable link and trolley slot.

b. Push master link cap over pins and past pin notches.

c. Slide clip-on spring over cap and onto pin notches until both pins are securely locked in

place.

3. With the trolley against the screwdriver, dispense the remainder of the cable/chain along the rail

toward the motor unit into the slot on the chain spreader, around the sprocket onto the chain

spreader and continuing to the trolley assembly and continuing to the trolley assembly. The

sprocket teeth must engage the chain. (b)

4. Check to make sure the chain is not twisted, then connect it to the threaded shaft with the

remaining master link.

5. Thread the inner nut and lock washer onto the trolley thread shaft

6. Insert the trolley threaded shaft through the hole in the trolley. Be sure the chain is not

twisted. (c)

7. Loosely thread the outer nut onto the trolley threaded shaft.

8. Remove the screwdriver.

HARDWARE

Master Link

Threaded Shaft

Lock Washer 5/16"-18Nut 5/16"-18

Sprocket

Threaded

Shaft

Front Rail

Section

(TO DOOR)

Inner

Nut

Lock

Washer

Master Link

Master

Link

Outer

Nut

Assembly

STEP 5 Tighten the chain

1. Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley.

2. To tighten the chain, turn the outer nut in the direction shown.

3. When the chain is approximately 1/4" (6 mm) above the base of the rail at it's midpoint, re-tighten

the inner nut to secure the adjustment.

Sprocket noise can result if the chain is too loose.

When installation is complete, you may notice some chain droop with the door closed. This is normal. If

the chain returns to the position shown when the door is open, do not re-adjust the chain.

NOTES:During future maintenance, ALWAYS pull the emergency release handle to disconnect the

trolley before adjusting the chain.

You may notice loosening of the chain after Adjustment Step 3 (Test the Safety Reversal System). Check

for proper tension and readjust chain if necessary. Then repeat Adjustment Step 3.

You have now finished assembling your garage door opener.Please read the following warnings

before proceeding to the installation section.

Base of Rail Mid length of Rail

Chain

1/4" (6 mm)

Outer

Nut

Lock

Washer

Trolley

Threaded

Shaft

Inner Nut

To Tighten

Inner Nut

To Tighten Outer Nut

Other manuals for HD220

This manual suits for next models

Table of contents

Other Chamberlain Garage Door Opener manuals

Chamberlain

Chamberlain 8010 User manual

Chamberlain

Chamberlain 3280C 1/2 HP User manual

Chamberlain

Chamberlain 8500W User manual

Chamberlain

Chamberlain APT Installation and operating instructions

Chamberlain

Chamberlain LiftMaster Premium 8355 User manual

Chamberlain

Chamberlain LiftMaster Professional 387LM User manual

Chamberlain

Chamberlain Power Drive Security+ PD210S User manual

Chamberlain

Chamberlain LiftMaster Security+ 2500 User manual

Chamberlain

Chamberlain Whisper Drive Security+ WD952KCS User manual

Chamberlain

Chamberlain Security+ 2565 User manual

Chamberlain

Chamberlain Security+ 3240 User manual

Chamberlain

Chamberlain LiftMaster 2500 User manual

Chamberlain

Chamberlain ARM 1703 Installation instructions

Chamberlain

Chamberlain LiftMaster 3575 User manual

Chamberlain

Chamberlain GH Manual

Chamberlain

Chamberlain POWER DRIVE PD432D 1/2 HP User manual

Chamberlain

Chamberlain LM750EVGB User manual

Chamberlain

Chamberlain LiftMaster 3275C User manual

Chamberlain

Chamberlain Merlin Whisper Drive MT3850WL User manual

Chamberlain

Chamberlain B4655T User manual

Chamberlain

Chamberlain 970CF User manual

Chamberlain

Chamberlain LiftMaster Professional 98LM User manual

Chamberlain

Chamberlain 1300 User manual

Chamberlain

Chamberlain ELITE Series User manual

Popular Garage Door Opener manuals by other brands

Dorma

Dorma ES 90 manual

Garaga

Garaga SECURITY+ 3265GCM 1HP owner's manual

Chase Doors

Chase Doors DuraShield installation manual

CSI

CSI Classic installation instructions

HATO

HATO 120 Automation manual

Richmond

Richmond GTR156 user manual

Raynor

Raynor 1280RGD owner's manual

CAME

CAME F4000 Series installation manual

B&D

B&D Controll-A-Door 5 instruction manual

BFT

BFT PRV AA SL Installation and user manual

Craftsman

Craftsman 139.53924 owner's manual

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift installation instructions

Westfalia

Westfalia 19 36 07 instruction manual

Cardin

Cardin BL Series instruction manual

Craftsman

Craftsman 139.53997D owner's manual

Bauer

Bauer CROSS18 Application. Installation and Maintenance Manual

Wayne-Dalton

Wayne-Dalton 8124 Installation instructions and owner's manual

Craftsman

Craftsman 139.18867 owner's manual