Central Pneumatic 69704 Assembly instructions

Page 2 For technical questions, please call 1-800-444-3353. Item 69704

NOTICE

Clean the Spray Gun IMMEDIATELY after use.

Delayed or inadequate cleaning will permanently clog the Spray Gun.

Table of Contents

Safety .................................................2

Specifications .....................................5

Setup ..................................................6

Operation............................................9

Maintenance......................................13

Parts List and Diagram......................18

Warranty ............................................20

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to

potential personal injury hazards. Obey all safety messages

that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

IMPORTANT SAFETY INSTRUCTIONS

INSTRUCTIONS PERTAINING TO A RISK OF FIRE,

ELECTRIC SHOCK, OR INJURY TO PERSONS

The warnings and precautions discussed in this manual cannot cover all possible conditions and

situations that may occur. It must be understood by the operator that common sense and caution

are factors which cannot be built into this product, but must be supplied by the operator.

WARNING – When using tools, basic precautions should always be followed, including the following:

Work Area

a. Keep the work area clean and well lighted.

Cluttered benches and dark areas

increase the risks of electric shock,

fire, and injury to persons.

b. Keep bystanders, children, and

visitors away while operating the tool.

Distractions are able to result in

the loss of control of the tool.

SAFETY OPERATION MAINTENANCESETUP

Page 3For technical questions, please call 1-800-444-3353.Item 69704

NOTICE

Clean the Spray Gun IMMEDIATELY after use.

Delayed or inadequate cleaning will permanently clog the Spray Gun.

Personal Safety

a. Stay alert. Watch what you are

doing and use common sense when

operating the tool. Do not use the

tool while tired or under the influence

of drugs, alcohol, or medication.

A moment of inattention while operating the

tool increases the risk of injury to persons.

b. Dress properly. Do not wear loose clothing

or jewelry. Contain long hair.

Keep hair, clothing, and gloves away

from moving parts. Loose clothes, jewelry, or

long hair increases the risk of injury to persons

as a result of being caught in moving parts.

c. Do not overreach. Keep proper

footing and balance at all times.

Proper footing and balance enables better

control of the tool in unexpected situations.

d. Use safety equipment.

Wear heavy-duty work gloves and

a NIOSH-approved respirator

during use. Non-skid safety shoes

and a hard hat must be used for the

applicable conditions.

e. Always wear eye protection.

Wear ANSI-approved

safety goggles.

Tool Use and Care

a. Do not force the tool. Use the correct

tool for the application. The correct tool

will do the job better and safer at the

rate for which the tool is designed.

b. Disconnect the tool from the air source

before making any adjustments,

changing accessories, or storing the tool.

Such preventive safety measures reduce

the risk of starting the tool unintentionally.

Turn off and detach the air supply, safely

discharge any residual air pressure, and

release the throttle and/or turn the switch to

its off position before leaving the work area.

c. Store the tool when it is idle out of reach

of children and other untrained persons.

A tool is dangerous in the hands

of untrained users.

d. Check for misalignment or binding of

moving parts, breakage of parts, and any

other condition that affects the tool’s

operation. If damaged, have the tool serviced

before using. Many accidents are caused

by poorly maintained tools. There is a risk

of bursting if the tool is damaged.

e. Use only accessories that are identified

by the manufacturer for the specific

tool model. Use of an accessory not

intended for use with the specific tool model,

increases the risk of injury to persons.

Service

a. Tool service must be performed only

by qualified repair personnel.

b. When servicing a tool, use only

identical replacement parts.

Use only authorized parts.

c. Use only lubricants supplied with the

tool or specified by the manufacturer.

SAFETYOPERATIONMAINTENANCE SETUP

Page 4 For technical questions, please call 1-800-444-3353. Item 69704

NOTICE

Clean the Spray Gun IMMEDIATELY after use.

Delayed or inadequate cleaning will permanently clog the Spray Gun.

Air Source

a. Never connect to an air source

that is capable of exceeding

200 psi. Over pressurizing the tool

may cause bursting, abnormal

operation, breakage of the tool or

serious injury to persons. Use only clean, dry,

regulated compressed air at the rated pressure

or within the rated pressure range as marked

on the tool. Always verify prior to using the

tool that the air source has been adjusted to

the rated air pressure or within the rated

air-pressure range.

b. Never use oxygen, carbon dioxide,

combustible gases or any bottled

gas as an air source for the tool.

Such gases are capable of explosion

and serious injury to persons.

SAVE THESE INSTRUCTIONS.

Symbol Definitions

Symbol Property or Statement

PSI Pounds per square inch of pressure

CFM Cubic Feet per Minute flow

SCFM Cubic Feet per Minute flow

at standard conditions

NPT National pipe thread, tapered

NPS National pipe thread, straight

Symbol Property or Statement

WARNING marking

concerning Risk of Eye Injury.

Wear ANSI-approved eye protection.

WARNING marking concerning

Risk of Respiratory Injury.

Wear NIOSH-approved respirator.

WARNING marking concerning

Risk of Explosion.

SAFETY OPERATION MAINTENANCESETUP

Page 5For technical questions, please call 1-800-444-3353.Item 69704

NOTICE

Clean the Spray Gun IMMEDIATELY after use.

Delayed or inadequate cleaning will permanently clog the Spray Gun.

Specific Safety Instructions

1. Do not direct spray at people or animals.

2. Do not exceed maximum air pressure.

3. Do not spray near open flames, pilot lights,

stoves, heaters, the air compressor, or

any other heat source. Most solvents and

coatings are highly flammable, particularly

when sprayed. Maintain a distance of at least

25 feet from the air compressor. If possible,

locate the air compressor in a separate room.

4. Read all of the information concerning

coating products and cleaning solvents.

Do not use chlorinated solvents

(e.g. 1-1-1 trichloroethylene and

dichloromethane, also known as

methylene chloride) to clean spray guns.

Many spray guns contain aluminum,

which reacts strongly to chlorinated

solvents. Contact the solvent or coating

manufacturer as needed regarding

potential chemical reactions.

5. Industrial applications must

follow OSHA requirements.

6. Spraying hazardous materials may

result in serious injury or death.

Do not spray pesticide, acid, corrosive

material, fertilizer, or toxic chemicals.

7. Paints and solvents may be harmful or fatal if

swallowed or inhaled. Avoid prolonged skin

contact with solvents or paints as they will

irritate skin. After any contact, immediately

wash off exposed area with hot, soapy water.

8. Attach all accessories properly to the

tool before connecting the air supply.

A loose accessory may detach

or break during operation.

9. Install an in-line shutoff valve

to allow immediate control over

the air supply in an emergency,

even if a hose is ruptured.

10. Air hose fittings may get hot during use.

Allow fittings to cool before disconnecting.

11. WARNING: Some dust created by power

sanding, sawing, grinding, drilling, and

other construction activities, contains

chemicals known [to the State of California]

to cause cancer, birth defects or other

reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement or

other masonry products

• Arsenic and chromium from

chemically treated lumber

Your risk from these exposures varies,

depending on how often you do this type

of work. To reduce your exposure to these

chemicals: work in a well ventilated area, and

work with approved safety equipment, such as

those dust masks that are specially designed

to filter out microscopic particles.

(California Health & Safety Code

§ 25249.5, et seq.)

WARNING: The brass components of

this product contain lead, a chemical

known to the State of California to cause

birth defects (or other reproductive harm).

(California Health & Safety Code

§ 25249.5, et seq.)

Specifications

Maximum Air Pressure 115 PSI

Air Inlet 1/4 IN. – 18 NPS

Nozzle Size 1.8 mm

Cup Capacity 1 quart

Air Consumption 10 CFM @ 60 PSI

Recommended Hose Size 3/8 IN. ID

SAFETYOPERATIONMAINTENANCE SETUP

Page 6 For technical questions, please call 1-800-444-3353. Item 69704

NOTICE

Clean the Spray Gun IMMEDIATELY after use.

Delayed or inadequate cleaning will permanently clog the Spray Gun.

Initial Set Up

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of

this product.

Note: For additional information regarding the parts listed in the following

pages, refer to the Assembly Diagram near the end of this manual.

Before Setup

1. This air tool may be shipped with a

protective plug covering the air inlet.

Remove this plug before set up.

2. Before first use, clean the Spray Gun using

a solvent-based thinner. If not removed,

the material used for testing and corrosion

prevention will contaminate paint.

Air Supply Setup

TO PREVENT SERIOUS INJURY FROM EXPLOSION:

Use only clean, dry, regulated, compressed air to power this tool. Do not use

oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power

source for this tool.

1. Incorporate a filter, regulator with pressure

gauge, in-line shutoff valve, and quick coupler

for best service, as shown on Figure A on

page 7 and Figure B on page 8.

An in-line shutoff ball valve is an important

safety device because it controls the air

supply even if the air hose is ruptured.

The shutoff valve should be a ball valve

because it can be closed quickly.

Note: Do not use an automatic oiler system or

add oil to airline. The oil will contaminate the

material being propelled, ruining the final result.

2. Attach an air hose to the

compressor’s air outlet. Connect the

air hose to the air inlet of the tool.

Other components, such as a coupler plug

and quick coupler, will make operation

more efficient, but are not required.

WARNING! TO PREVENT SERIOUS INJURY

FROM ACCIDENTAL OPERATION:

Do not install a female quick coupler

on the tool. Such a coupler contains

an air valve that will allow the air tool to

retain pressure and operate accidentally

after the air supply is disconnected.

Note: Air flow, and therefore tool

performance, can be hindered by

undersized air supply components.

3. The air hose must be long enough to reach

the work area with enough extra length

to allow free movement while working.

4. Close the in-line shutoff valve between

the compressor and the tool.

5. Turn on the air compressor according to

the manufacturer’s directions and allow it

to build up pressure until it cycles off.

SAFETY OPERATION MAINTENANCESETUP

Page 7For technical questions, please call 1-800-444-3353.Item 69704

NOTICE

Clean the Spray Gun IMMEDIATELY after use.

Delayed or inadequate cleaning will permanently clog the Spray Gun.

Figure A: Portable Air Supply Setup

E F

Description Function

A Air Hose Connects air to tool

B Filter Prevents dirt and condensation from damaging tool or workpiece

D Regulator Adjusts air pressure to tool

E Coupler and Plug Provides quick connection and release

C Air Cleaner / Dryer*Prevents water vapor from damaging workpiece

FAir Adjusting Valve*For fine tuning airflow at tool

*Optional components.

6. Adjust the air compressor’s output

regulator so that the air output is enough

to properly power the tool, but the output

will not exceed the tool’s maximum air

pressure at any time. Adjust the pressure

gradually, while checking the air output

gauge to set the right pressure range.

7. Inspect the air connections for leaks.

Repair any leaks found.

8. If the tool will not be used at this time,

turn off and detach the air supply and

safely discharge any residual air pressure

to prevent accidental operation.

Note: Residual air pressure should not be

present after the tool is disconnected from

the air supply. However, it is a good safety

measure to attempt to discharge the tool in a

safe fashion after disconnecting to ensure that

the tool is disconnected and unpowered.

SAFETYOPERATIONMAINTENANCE SETUP

Page 8 For technical questions, please call 1-800-444-3353. Item 69704

NOTICE

Clean the Spray Gun IMMEDIATELY after use.

Delayed or inadequate cleaning will permanently clog the Spray Gun.

Figure B: Stationary Air Supply Setup

L O

Non-lubricated

Tools

Lubricated

Tools

JKH

Slope

B B

A A

Description Function

A Vibration Pads For noise and vibration reduction

B Anchor Bolts Secures air compressor in place

C Ball Valve Isolates sections of system

for maintenance

D Isolation Hose For vibration reduction

EMain Air Line - 3/4″ min. Distributes air to branch lines

F Ball Valve To drain moisture from system

GBranch Air Line -1/2″ min. Brings air to point of use

H Air Hose Connects air to tool

Description Function

I Filter Prevents dirt and condensation

contamination

J Regulator Adjusts air pressure to tool

K Lubricator*For air tool lubrication

L Coupler and Plug Provides quick connection

and release

M Leader Hose*Increases coupler life

N Air Cleaner / Dryer*Prevents moisture contamination

OAir Adjusting Valve*For fine tuning airflow at tool

*Optional components.

SAFETY OPERATION MAINTENANCESETUP

Page 9For technical questions, please call 1-800-444-3353.Item 69704

NOTICE

Clean the Spray Gun IMMEDIATELY after use.

Delayed or inadequate cleaning will permanently clog the Spray Gun.

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this

product.

Inspect tool before use, looking for damaged, loose, and missing parts.

If any problems are found, do not use tool until repaired.

Workpiece and Work Area Set Up

1. Designate a work area that is clean

and well-lit. The work area must not

allow access by children or pets to

prevent distraction and injury.

2. Route the air hose along a safe

path to reach the work area without

creating a tripping hazard or exposing

the air hose to possible damage.

The air hose must be long enough to reach

the work area with enough extra length

to allow free movement while working.

3. Before spraying, mask nearby

objects not being sprayed and lay

cloths (not included) on the floors.

Nozzle

Trigger

Lock Ring

Fluid

Knob

Air Inlet

Cup

Figure C: Components and Controls

Cup Locking

Lever

Cup Cover Cup Mounting

Yoke

Pattern

Adjustment

Knob

SAFETYOPERATIONMAINTENANCE SETUP

Page 10 For technical questions, please call 1-800-444-3353. Item 69704

NOTICE

Clean the Spray Gun IMMEDIATELY after use.

Delayed or inadequate cleaning will permanently clog the Spray Gun.

Spray Gun Setup Adjustment

TO PREVENT SERIOUS INJURY:

Do not adjust or tamper with any control or component in a way not specifically explained

within this manual. Improper adjustment can result in tool failure or other serious hazards.

CAUTION! Keep hands away from Trigger while making adjustments.

Note: This Spray Gun is meant for spraying

oil-based paints. It is not recommended for

regular wall paint or thin coatings of any type.

While these products can be used with

this Spray Gun, coverage will not be even.

Paint Preparation and Filling

Note: Proper paint mixture is essential.

Follow the manufacturer’s directions. Most paints

will spray easily if they are thinned properly.

1. Thin the paint according to manufacturer’s

directions and mix thoroughly.

2. Carefully strain the paint through

a paint strainer or a piece of cheesecloth.

3. Separate the Cup from the Spray Gun by

moving the Cup Locking Lever on top of

the Cup Cover out of the locked position

to release the Cup Mounting Yoke.

4. Fill the Cup to 3/4 full. Place the Cup back

in the Cup Mounting Yoke, rotate the Cup

to lock it onto the yoke, and move the Cup

Locking Lever to the locked position.

5. Start the air compressor and set

the regulator to needed pressure.

Do not exceed maximum air pressure.

6. Test the consistency by spraying

on a piece of scrap material.

If it still appears too thick, add a very

small amount of thinner (not included)

and mix thoroughly. Use the proper

thinner for the type of paint. Thin

CAUTIOUSLY. Proceed slowly,

adding minimal amounts at a time.

DO NOT exceed the manufacturer’s

thinning recommendations.

Fan Direction

Figure D: Fan Direction

Horizontal Fan

Vertical

Fan

Nozzle

Lock Ring

To change the direction of the

fan from horizontal to vertical,

loosen the Lock Ring and turn the Nozzle 90°.

8. After the adjustment, tighten

the Lock Ring by hand.

Pattern Adjustment

WARNING! Do not exceed the Maximum Air

Pressure shown on the Specification chart.

9. Adjust the air supply pressure during

operation with the Trigger fully depressed and

the Air Knob fully open.

If reducing air pressure for specific areas,

use the Air Knob.

SAFETY OPERATION MAINTENANCESETUP

Table of contents

Other Central Pneumatic Paint Sprayer manuals

Central Pneumatic

Central Pneumatic 93506 User manual

Central Pneumatic

Central Pneumatic 43760 User manual

Central Pneumatic

Central Pneumatic 47016 Assembly instructions

Central Pneumatic

Central Pneumatic 47016 User guide

Central Pneumatic

Central Pneumatic 47016 67181 Assembly instructions

Central Pneumatic

Central Pneumatic 62381 User manual

Central Pneumatic

Central Pneumatic 60314 Assembly instructions

Central Pneumatic

Central Pneumatic PAINT SPRAY GUN 30224 User manual

Central Pneumatic

Central Pneumatic 93270 User manual

Central Pneumatic

Central Pneumatic 86 Installation manual

Central Pneumatic

Central Pneumatic 2471 User manual

Central Pneumatic

Central Pneumatic 69724 Assembly instructions

Central Pneumatic

Central Pneumatic HVLP DETAIL SPRAY GUN 46719 User manual

Central Pneumatic

Central Pneumatic 94605 Parts list manual

Central Pneumatic

Central Pneumatic 00422 User manual

Central Pneumatic

Central Pneumatic 43760 User manual

Central Pneumatic

Central Pneumatic 47016 User guide

Central Pneumatic

Central Pneumatic CENTRAL PNEUMATIC 92841 Installation manual

Central Pneumatic

Central Pneumatic 97855 Installation manual

Central Pneumatic

Central Pneumatic 90985 User manual

Central Pneumatic

Central Pneumatic 99959 Installation manual

Central Pneumatic

Central Pneumatic 38308 User manual

Central Pneumatic

Central Pneumatic CENTRAL PNEUMATIC 93305 User guide

Central Pneumatic

Central Pneumatic 66801 Installation manual

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Graco

Graco 246737 Repair and parts

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

Graco

Graco EM 390 Instructions-parts list

DeVilbiss

DeVilbiss LUNA2i Operation manual