Central Pneumatic 92921 User manual

1/2” AIR COMPOSITE

IMPACT WRENCH

ASSEMBLY AND OPERATING

INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

Model 92921

artwork contained herein may be reproduced in any shape or form without the express written

consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353.

Manual Revised 11h

TO PREVENT SERIOUS INJURY,

READ AND UNDERSTAND ALL WARNINGS

AND INSTRUCTIONS BEFORE USE.

Page 2SKU 92921 For technical questions, please call 1-800-444-3353

Specications

Save This Manual

You will need the manual for the safety warnings and precautions, assembly instructions,

operating and maintenance procedures, parts list and diagram. Keep your invoice with this

manual. Write the invoice number on the inside of the front cover. Keep the manual and

invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tool, basic safety precautions should always be followed to

reduce the risk of personal injury and damage to equipment.

Read all instructions before using this tool!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use machines or power tools in damp or wet

locations. Don’t expose to rain. Keep work area well lighted. Do not use electrically

powered compressors in the presence of ammable gases or liquids.

3. Keep children away. Children must never be allowed in the work area. Do not let

them handle machines, tools, extension cords, or air hoses.

4. Store idle equipment. When not in use, tools must be stored in a dry location to

inhibit rust. Always lock up tools and keep out of reach of children.

5. Use the right tool for the job. Do not attempt to force a small tool or attachment

to do the work of a larger industrial tool. There are certain applications for which this

tool was designed. It will do the job better and more safely at the rate for which it was

intended. Do not modify this tool and do not use this tool for a purpose for which it

was not intended.

6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in

moving parts. Protective, electrically non-conductive clothes and non-skid footwear

are recommended when working. Wear restrictive hair covering to contain long hair.

7. Use eye and ear protection. Always wear ANSI approved impact safety

goggles and hearing protection. Wear a full face shield if you are producing

metal lings or wood chips. Wear an ANSI approved dust mask or respirator

when working around metal, wood, and chemical dusts and mists.

Maximum Torque 260 Ft. Lbs.

Drive Size 1/2”

Impact Mechanism Rocking Dog

Air Inlet 1/4” - 18 NPT

Recommended Air Pressure 90 PSI

No Load RPM 7,000

Air Consumption 4.5 CFM

Page 3SKU 92921 For technical questions, please call 1-800-444-3353

8. Do not overreach. Keep proper footing and balance at all times. Do not reach over

or across running machines or air hoses.

9. Maintain tools with care. Keep tools clean for better and safer performance. Follow

instructions for lubricating and changing accessories. Inspect tool cords and air hoses

periodically and, if damaged, have them repaired by an authorized technician. The

handles must be kept clean, dry, and free from oil and grease at all times.

10. Disconnect air supply. Disconnect air hose when not in use.

11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches

are removed from the tool or machine work surface before plugging it in.

12. Avoid unintentional starting. Be sure the trigger is released when not in use and

before plugging in. Do not carry any tool with your nger on the trigger, whether it is

plugged in or not.

13. Stay alert. Watch what you are doing, use common sense. Do not operate any tool

when you are tired.

14. Check for damaged parts. Before using any tool, any part that appears damaged

should be carefully checked to determine that it will operate properly and perform its

intended function. Check for alignment and binding of moving parts; any broken parts

or mounting xtures; and any other condition that may affect proper operation. Any

part that is damaged should be properly repaired or replaced by a qualied technician.

Do not use the tool if any switch does not turn On and Off properly.

15. Guard against electric shock. Prevent body contact with grounded surfaces such as

pipes, radiators, ranges, and refrigerator enclosures.

16. Replacement parts and accessories. When servicing, use only identical

replacement parts. Use of any other parts will void the warranty. Only use accessories

intended for use with this tool. Approved accessories are available from Harbor

Freight Tools.

17. Do not operate tool if under the inuence of alcohol or drugs. Read warning

labels if taking prescription medicine to determine if your judgement or reexes are

impaired while taking drugs. If there is any doubt, do not operate the Wrench.

18. Use proper size and type extension cord. If an extension cord is required, it

must be of the proper size and type to supply the correct current to the compressor

without heating up. Otherwise, the extension cord could melt and catch re, or cause

electrical damage to the compressor. Check your air compressor’s manual for the

appropriate size cord.

19. Maintenance. For your safety, maintenance should be performed regularly by a

qualied technician.

20. Compressed air only. Never use combustible gas as a power source.

21. This Impact Wrench should only be used with impact sockets and extensions.

Using any other accessories can cause the accessories to break, causing permanent

damage to the unit and severe injury to the operator.

Page 4SKU 92921 For technical questions, please call 1-800-444-3353

Unpacking

When unpacking, check to make sure the parts listed on page 8 are included. If any

parts are missing or broken, please call Harbor Freight Tools at the number on the cover of

this manual as soon as possible.

1. You will need to prepare a 3/8” air connector (not included) to connect to the Air Inlet

(40) on the Impact Wrench. First, wrap the 3/8” air connector with pipe thread seal tape

before threading it into the Air Inlet (40). Connect the 3/8” ID Air Source Hose to a quick

connect coupler (not included), and then to the Impact Wrench.

Note: If you are not using an automatic oiler system, before operation, add a few drops

of Pneumatic Tool Oil to the airline connection. Add a few drops more after each hour

of continual use.

2. Set the air pressure on the regulator to 90 PSI. Do not exceed the recommended

air pressure of 90 PSI.

3. Check the air connection for leaks. Disconnect from the air source.

Operation

For best service you should incorporate an oiler, regulator, and inline lter, as shown in the

diagram above. Hoses, couplers, oilers, regulators, and lters are all available at Harbor

Freight Tools.

Impact

Wrench

Note: Performance of the compressor (if powered by line voltage) may vary depending

on variations in local line voltage. Extension cord usage may also affect tool

performance.

Warning: The warnings, cautions, and instructions discussed in this instruction manual

cannot cover all possible conditions and situations that may occur. It must be un-

derstood by the operator that common sense and caution are factors which cannot be

built into this product, but must be supplied by the operator.

Page 5SKU 92921 For technical questions, please call 1-800-444-3353

Operation (continued)

Note: Turn off your air compressor and disconnect the air hose when you are changing

sockets. After you attach the socket, attach the air hose and turn the air compressor

on.

4. Select the appropriate size 1/2” drive socket for your needs. Note: Use only impact

type sockets.

5. Push and snap the socket (not included) onto the Anvil (23).

6. To operate the Regulator Knob (17) and Forward / Reverse direction:

For Forward (clockwise) direction, set knob to the right. Note: There are

3 torque setting stops for Forward.

For Reverse (counterclockwise) direction, set knob to the left. Note:

There is 1 torque setting stop for Reverse.

7. Tighten the nut as tight as you can by hand.

8. Place the socket (not included) over the nut you wish to tighten.

9. Grip the Impact Wrench rmly with two hands and gently squeeze the Trigger (30).

Note: If the Impact Wrench cannot tighten the nut to your satisfaction, do not raise the air

pressure on the compressor over 90 PSI. Pressures above 90 PSI will strip the work-

piece and damage the tool, potentially causing the tool to fail, causing serious injury.

Use other appropriate methods and tools to tighten the nut.

10. When the nut is tightened, release the Trigger (30). Turn off the air compressor and

disconnect the hose.

11. If available, check the recommended torque specication for the nut. Use a torque

wrench to tighten the nut to the proper setting after using the Impact Wrench.

Loosening

Note: Set the Regulator Knob (17) to the left so that the anvil turns counterclockwise (reverse).

12. Place the socket (not included) over the nut you wish to loosen.

13. Grip the Impact Wrench rmly with two hands and gently squeeze the Trigger (30).

Note: If the Impact Wrench cannot loosen the nut, do not raise the air pressure on the

compressor over 90 PSI. Do not attempt to loosen the nut with the Impact Wrench.

Use other appropriate methods and tools to loosen the nut.

14. When the nut is loosened, release the Trigger (30). Turn off the air compressor and

disconnect the hose.

15. If needed, remove the nut from the socket.

Refer to FIGURE 1 on page 6, and the Assembly Drawing on page 8.

Warning!! This Impact Wrench supplies powerful torque and is designed to be operated with

two hands. Failure to operate the Impact Wrench with two hands may result in serious injury.

Page 6SKU 92921 For technical questions, please call 1-800-444-3353

90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that

its products meet high quality and durability standards,

and warrants to the original purchaser that this product

is free from defects in materials and workmanship for

the period of 90 days from the date of purchase. This

warranty does not apply to damage due directly or

indirectly, to misuse, abuse, negligence or accidents,

repairs or alterations outside our facilities, criminal activity,

improper installation, normal wear and tear, or to lack of

maintenance. We shall in no event be liable for death,

injuries to persons or property, or for incidental, contingent,

special or consequential damages arising from the use

of our product. Some states do not allow the exclusion or

limitation of incidental or consequential damages, so the

above limitation of exclusion may not apply to you. THIS

WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE

WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part

must be returned to us with transportation charges prepaid.

Proof of purchase date and an explanation of the complaint

must accompany the merchandise. If our inspection veries

the defect, we will either repair or replace the product at our

election or we may elect to refund the purchase price if we

cannot readily and quickly provide you with a replacement.

We will return repaired products at our expense, but if we

determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you

must bear the cost of returning the product.

This warranty gives you specic legal rights and you may

also have other rights which vary from state to state.

1. Make sure your Impact Wrench is disconnected from the air hose before attempting

any maintenance.

2. Wipe the Impact Wrench down with a lint free cloth after each use.

3. Make sure the Anvil (23) is clear of dirt or debris. If possible, spray it with compressed

air before each use.

4. Annually, or more often if used on a daily basis, inject oil into the oil port located on the

right side of the Housing (28).

5. If you do not use an inline oiler/lter system, lubricate the tool daily by holding it so that

the Air Inlet (40) is facing up. Squeeze the Trigger (30), and place one or two drops of

oil into the Air Inlet (40). Squeezing the Trigger (30) allows the oil to circulate in the

motor.

Maintenance

Page 7SKU 92921 For technical questions, please call 1-800-444-3353

NOTE: Some parts are listed and shown for illustration purposes only and are not available

individually as replacement parts.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR

DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE

BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR

THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT,

THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS

AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED

TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT

PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT

PARTS THERETO.

Parts List

Page 8SKU 92921 For technical questions, please call 1-800-444-3353

Assembly Drawing

Table of contents

Other Central Pneumatic Impact Driver manuals

Central Pneumatic

Central Pneumatic 94108 User manual

Central Pneumatic

Central Pneumatic 69228 User manual

Central Pneumatic

Central Pneumatic Earthquake 92453 Installation manual

Central Pneumatic

Central Pneumatic Earthquake 92421 User manual

Central Pneumatic

Central Pneumatic 93566 Quick reference guide

Central Pneumatic

Central Pneumatic 37730 User manual

Central Pneumatic

Central Pneumatic 95310 User manual

Central Pneumatic

Central Pneumatic 69576 Assembly instructions

Central Pneumatic

Central Pneumatic ITEM 93296 Assembly instructions

Central Pneumatic

Central Pneumatic 95310 User manual

Central Pneumatic

Central Pneumatic 60629 User manual

Central Pneumatic

Central Pneumatic 2623 User manual

Central Pneumatic

Central Pneumatic 92921 User manual

Central Pneumatic

Central Pneumatic Earthquake 92453 User manual

Central Pneumatic

Central Pneumatic Earthquake 92421 Installation manual

Central Pneumatic

Central Pneumatic 92622 User manual

Central Pneumatic

Central Pneumatic 53176 User manual

Central Pneumatic

Central Pneumatic 95310 Installation manual

Central Pneumatic

Central Pneumatic 92208 Parts list manual

Central Pneumatic

Central Pneumatic 95141 Installation manual

Central Pneumatic

Central Pneumatic Earthquake 92353 User manual

Central Pneumatic

Central Pneumatic 32871 User manual

Central Pneumatic

Central Pneumatic 92037 Original instruction manual

Central Pneumatic

Central Pneumatic 33567 Assembly and User manual

Popular Impact Driver manuals by other brands

stayer

stayer IW500D operating instructions

Makita

Makita DTD152 instruction manual

Milwaukee

Milwaukee M12 FID Original instructions

Grizzly

Grizzly H6140 instruction sheet

Makita

Makita BTW450 user manual

Ozito

Ozito LID-3000 instruction manual

Astro Pneumatic Tool

Astro Pneumatic Tool 1812 manual

Greenlee

Greenlee HW3 Service manual

Sthor

Sthor 57091 manual

Makita

Makita DTD145 instruction manual

Hilti

Hilti SIW 2-A12 manual

Ryobi

Ryobi R18IW3 Original instructions

Parkside

Parkside PDSSA 20-Li A1 Translation of the original instructions

Flex

Flex FX1471 Operator's manual

SATA

SATA 51075C operation instruction

Cembre

Cembre NR-11P Operation and maintenance manual

Makita

Makita BTP131RFE instruction manual

DeWalt

DeWalt XR Li-ion DCF902 instruction manual