Central Pneumatic 90234 User manual

COMPRESSOR

4 HP - 10 GALLON

Model 90234

OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at: http://www.harborfreight.com

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions, please call 1-800-444-3353.

PRODUCT SPECIFICATIONS

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures, parts list and as-

sembly diagram. Keep your invoice with this manual. Write the invoice number

on the inside of the front cover. Keep this manual and invoice in a safe and dry

place for future reference.

GENERAL SAFETY RULES

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow all instructions listed below may result in

electric shock, fire, and/or serious injury.

SAVE THESE INSTRUCTIONS

WORK AREA

1. Keep your work area clean and well lit. Cluttered benches and dark areas

invite accidents.

SKU 90234 PAGE 2 REV 04/04

metInoitpircseD

stnemeriuqeRlacirtcelE zH06/V021/detaRPH3/kaePPH4 rotoMroticapaCowT;MPR0043 noitcetorPdaolrevOlamrehT

ISPmumixaMISP511

seirevileDriA ISP09@MFCS6.5/ISP511@MFCS5.4 ISP04@MFCS2.7/ISP07@MFCS2.6

yticapaCknaTriAsnollaG01

ffO-tuhScitamotuA tratseRcitamotuA ISP511@ffO-tuhScitamotuA ISP58@tratseRcitamotuA

yticapaCliOsecnuO53.52

eziSteltuOriAsdaerhTelaMTPN81-"4/1

thgieWteNsdnuoP05.57

3. Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control. Protect others in the work area from

debris such as chips and sparks. Provide barriers or shields as needed.

ELECTRICAL SAFETY

4. Grounded tools must be plugged into an outlet properly installed and

grounded in accordance with all codes and ordinances. Never remove the

grounding prong or modify the plug in any way. Do not use any adapter

plugs. Check with a qualified electrician if you are in doubt as to whether

the outlet is properly grounded. If the tools should electrically malfunction or

break down, grounding provides a low resistance path to carry electricity away

from the user.

5. Double insulated tools are equipped with a polarized plug (one blade is

wider than the other). This plug will fit in a polarized outlet only one way. If

the plug does not fit fully in the outlet, reverse the plug. If it still does not

fit, contact a qualified electrician to install a polarized outlet. Do not

change the plug in any way. Double insulation eliminates the need for the

three wire grounded power cord and grounded power supply system.

6. Avoid body contact with grounded surfaces such as pipes, radiators,

ranges, and refrigerators. There is an increased risk of electric shock if your

body is grounded.

7. Do not expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

8. Do not abuse the Power Cord. Never use the Power Cord to carry the tools

or pull the Plug from an outlet. Keep the Power Cord away from heat, oil,

sharp edges, or moving parts. Replace damaged Power Cords immedi-

ately. Damaged Power Cords increase the risk of electric shock.

PERSONAL SAFETY

9. Stay alert. Watch what you are doing, and use common sense when oper-

ating a power tool. Do not use a power tool while tired or under the influ-

ence of drugs, alcohol, or medication. A moment of inattention while operat-

ing power tools may result in serious personal injury.

SKU 90234 PAGE 3

2. Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases, or dust. Power tools create sparks

which may ignite the dust or fumes.

10. Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away from moving parts. Loose

clothes, jewelry, or long hair can be caught in moving parts.

11. Avoid accidental starting. Be sure the Power Switch is off before plugging

in. Carrying power tools with your finger on the Power Switch, or plugging in

power tools with the Power Switch on, invites accidents.

12. Remove adjusting keys or wrenches before turning the power tool on. A

wrench or a key that is left attached to a rotating part of the power tool may result

in personal injury.

13. Do not overreach. Keep proper footing and balance at all times. Proper

footing and balance enables better control of the power tool in unexpected

situations.

14. Use safety equipment. Always wear eye protection. Dust mask, non-skid

safety shoes, hard hat, or hearing protection must be used for appropriate

conditions.

TOOL USE AND CARE

15. Do not force the tool. Use the correct tool for your application. The correct

tool will do the job better and safer at the rate for which it is designed.

16. Do not use the power tool if the Power Switch does not turn it on or off.

Any tool that cannot be controlled with the Power Switch is dangerous and must

be replaced.

17. Disconnect the Power Cord Plug from the power source before making any

adjustments, changing accessories, or storing the tool. Such preventive

safety measures reduce the risk of starting the tool accidentally.

18. Store idle tools out of reach of children and other untrained persons. Tools

are dangerous in the hands of untrained users.

19. Maintain tools with care. Keep cutting tools sharp and clean. Properly

maintained tools with a sharp cutting edge are less likely to bind and are easier

to control. Do not use a damaged tool. Tag damaged tools “Do not use” until

repaired.

SKU 90234 PAGE 4

20. Check for misalignment or binding of moving parts, breakage of parts, and

any other condition that may affect the tool’s operation. If damaged, have

the tool serviced before using. Many accidents are caused by poorly

maintained tools.

21. Use only accessories that are recommended by the manufacturer for your

model. Accessories that may be suitable for one tool may become hazardous

when used on another tool.

SERVICE

22. Tool service must be performed only by qualified repair personnel. Service

or maintenance performed by unqualified personnel could result in a risk of injury.

23. When servicing a tool, use only identical replacement parts. Follow

instructions in the

“Inspection, Maintenance, And Cleaning”

section of this

manual. Use of unauthorized parts or failure to follow maintenance instructions

may create a risk of electric shock or injury.

GROUNDING

SKU 90234 PAGE 5

WARNING!

Improperly connecting the grounding wire can result in the risk of electric

shock. Check with a qualfified electrician if you are in doubt as to whether the

outlet is properly grounded. Do not modify the power cord plug provided with

the tool. Never remove the grounding prong from the plug. Do not use the

tool if the power cord or plug is damaged. If damaged, have it repaired by

a service facility before use. If the plug will not fit the outlet, have a proper

outlet installed by a qualified electrician.

GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS

1. Tools marked with “Grounding Required” have a three wire cord and three prong

grounding plug. The plug must be connected to a properly grounded outlet. If

the tool should electrically malfunction or break down, grounding provides a low

resistance path to carry electricity away from the user, reducing the risk of elec-

tric shock. (See Figure A, next page.)

2. The grounding prong in the plug is connected through the green wire inside the

cord to the grounding system in the tool. The green wire in the cord must be the

only wire connected to the tool’s grounding system and must never be attached

to an electrically “live” terminal. (See Figure A.)

3. Your tool must be plugged into an appropriate outlet, properly installed and

grounded in accordance with all codes and ordinances. The plug and outlet

should look like those in the following illustration. (See Figure A.)

FIGURE A

SKU 90234 PAGE 6

DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS

4. Tools marked “Double Insulated” do not require grounding. They have a special

double insulation system which satisfies OSHA requirements and complies with

the applicable standards of Underwriters Laboratories, Inc., the Canadian

Standard Association, and the National Electrical Code. (See Figure B.)

5. Double insulated tools may be used in either of the 120 volt outlets shown in the

following illustration. (See Figure B.)

FIGURE B

SKU 90234 PAGE 7

SYMBOLOGY

V ~

xxxx/min.

Double Insulated

Canadian Standards

Association

Underwriters

Laboratories, Inc.

Volts Alternating Current

Amperes

No Load Revolutions

per Minute (RPM)

SPECIFIC SAFETY RULES

1. Maintain a safe working environment. Keep the work area well lit. Make sure

there is adequate surrounding workspace. Always keep the work area free of

obstructions, grease, oil, trash, and other debris. Do not use this product in

areas near flammable chemicals, dusts, and vapors.

2. Maintain labels and nameplates on the Air Compressor. These carry

important information. If unreadable or missing, contact Harbor Freight Tools for

a replacement.

3. Use eye and hearing protection. Always wear ANSI approved safety impact

eye goggles and hearing protectors when using this product.

4. Do not allow children to use or play with this product.

5. Store idle equipment. When not in use, tools and equipment should be stored

in a dry location to inhibit rust. Always lock up tools and equipment, and keep out

of reach of children.

6. Do not use this product if under the influence of alcohol or drugs. Read

warning labels on prescriptions to determine if your judgement or reflexes are

impaired while taking drugs. If there is any doubt, do not attempt to use this

product.

7. Make sure to fill the Air Compressor with a premium quality, 30-weight,

non-detergent, compressor oil before each use. Running the Air Compressor

with no oil or low oil will cause damage to the equipment and void the warranty.

SKU 90234 PAGE 8

8. When checking the oil level, make sure to unscrew (do not pull) the Oil

Plug (part #78) out.

9. Drain the Air Compressor’sTank (part #50) every day. Do not allow moisture

to build up inside the Tank. Do not open the Tank Drain Valve (part #59) so that

more than four threads are showing.

10. Avoid injury. Never direct the Air Outlet Valve (part #69) at people or animals.

11. Do not alter or remove the factory sealed Pressure ReliefValve (part #67).

12. Dress properly. Do not wear loose clothing or jewelry as they can be caught in

moving parts. Wear restrictive hair covering to contain long hair.

13. Do not overreach. Keep proper footing and balance at all times. Do not reach

over or across running machines.

15. Industrial applications must follow OSHA requirements.

16. Maintain this product with care. Keep this product clean for better and safer

performance.

17. Maintenance: For your safety, service and maintenance should be performed

regularly by a qualified technician.

18. Check for damaged parts. Before using this product, carefully check that it will

operate properly and perform its intended function. Check for damaged parts

and any other conditions that may affect the operation of this product. Replace

or repair damaged or worn parts immediately.

19. Replacement parts and accessories: When servicing, use only identical re-

placement parts. Only use accessories intended for use with this product.

20. Use the right tool or attachment for the job. Do not attempt to force a small

tool or attachment to do the work of a larger industrial tool or attachment.

There are certain applications for which this product was designed. It will do the

job better and more safely at the rate for which it was intended. Do not modify

this product, and do not use this product for a purpose for which it was not in-

tended.

21. To extend the life of your air tools and equipment: It is recommended to

install a water filter and oiler (available from Harbor Freight Tools) in series with

the Air Outlet Valve (part #69) of the Air Compressor.

(See Figure C, next page.)

22. WARNING! People with pacemakers should consult their physician(s)

before using this product. Operation of electrical equipment in close proximity to

a heart pacemaker could cause interference or failure of the pacemaker.

23. WARNING! The warnings, precautions, and instructions discussed in this

manual cannot cover all possible conditions and situations that may occur. The

operator must understand that common sense and caution are factors which

cannot be built into this product, but must be supplied by the operator.

NOTE: For additional information regarding the parts mentioned in the following pages,

refer to the Assembly Diagram on page 16.

1. IMPORTANT! Always fill the Air Compressor with a premium quality,

SKU 90234 PAGE 9

OPERATING INSTRUCTIONS

UNPACKING

When unpacking, check to make sure all the parts shown on the Parts List on pages 14

and 15 are included. If any parts are missing or broken, please call Harbor Freight Tools

at the number shown on the cover of this manual as soon as possible.

AIR TOOL

WATER

FILTER OILER

FIGURE C

AIR OUTLET

VALVE

(#69)

30-weight, non-detergent, compressor oil before each use. Running the Air

Compressor with no oil or low oil will cause damage to the equipment and

void the warranty. To check the level of oil, make sure the Air Compressor is

OFF. Then, observe the Oil Level Window (part #72). The level of oil should just

reach the horizontal line as shown on the Oil Level Window. If the level of oil is

below the horizontal line, remove the Oil Plug (part #78) and add new oil through

the Oil Plug hole.

Make sure not to overfill. The Air Compressor is designed to

hold approximately 25 fluid ounces of oil.

Then screw in the Oil Plug, being

careful not to strip the threads.

(See Figure D.)

2. Turn the Air Outlet Valve (part #69) to its CLOSED position. Then connect a high

pressure air hose (not included) equipped with a

quick connector

to the Air Outlet

Valve. If using a water filter and oiler in series with the Air Outlet Valve of the Air

Compressor, connect the other end of the air hose to the water filter and oiler and

connect the water filter and oiler to the air tool being used. If not using a water

filter and oiler, squirt several drops of air tool oil into the air intake plug of the air

tool. Then, connect the other end of the air hose directly from the Air Outlet

Valve of the Air Compressor to the air tool.

(See Figure E, and Figure F, next page.)

AIR

OUTLET

VALVE

(#69)

CONNECT

AIR HOSE HERE.

CLOSED POSITION

OPEN POSITION

FIGURE E

SKU 90234 PAGE 10 REV 04/04

OIL LEVEL

WINDOW

(#72)

PRESSURE RELIEF

VALVE

(#67)

OIL PLUG

(#78)

FIGURE D

Table of contents

Other Central Pneumatic Air Compressor manuals

Central Pneumatic

Central Pneumatic 96068 Installation manual

Central Pneumatic

Central Pneumatic 60754 User manual

Central Pneumatic

Central Pneumatic 90749 User manual

Central Pneumatic

Central Pneumatic 67708 Installation manual

Central Pneumatic

Central Pneumatic CentralPneumatic 17 GAL Assembly instructions

Central Pneumatic

Central Pneumatic 47915 User manual

Central Pneumatic

Central Pneumatic 61489 User manual

Central Pneumatic

Central Pneumatic 92097 User manual

Central Pneumatic

Central Pneumatic 94734 Installation manual

Central Pneumatic

Central Pneumatic 67696 Installation manual

Central Pneumatic

Central Pneumatic 61454 User manual

Central Pneumatic

Central Pneumatic 67696 Assembly instructions

Central Pneumatic

Central Pneumatic PROFESSIONAL 99901 User manual

Central Pneumatic

Central Pneumatic 95498 Installation manual

Central Pneumatic

Central Pneumatic 21 User manual

Central Pneumatic

Central Pneumatic 40131 Assembly instructions

Central Pneumatic

Central Pneumatic 60567 Original instruction manual

Central Pneumatic

Central Pneumatic 93271 Installation manual

Central Pneumatic

Central Pneumatic 61615 Assembly instructions

Central Pneumatic

Central Pneumatic 93785 User manual

Central Pneumatic

Central Pneumatic Central Pneumatic 30 Gallon, 180 PSI Gas Powered Two-Stage Air... User manual

Central Pneumatic

Central Pneumatic 67696 Installation manual

Central Pneumatic

Central Pneumatic 67698 User manual

Central Pneumatic

Central Pneumatic CENTRAL PNEUMATIC 47407 Parts list manual

Popular Air Compressor manuals by other brands

Sparmax

Sparmax DC-25XR user manual

KAESER

KAESER M122 Service manual

GMC

GMC GAC1500 Original instructions

Briggs & Stratton

Briggs & Stratton Air Compressor Operator's manual

Fini

Fini F3GST2TK Operator's manual

Industrial Air

Industrial Air CP1580325 Operator's & parts manual

Campbell Hausfeld

Campbell Hausfeld RP3300 Easy setup guide

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Option manual

Hitachi

Hitachi EC99S Instruction manual and safety instructions

Parkside

Parkside PKO 270 A1 operating instructions

Sullair

Sullair 185 manual

Clas Ohlson

Clas Ohlson QIE-ZTH-15 manual

Ferm

Ferm CRM1046 Original instructions

BE AC153 Operation manual

RIDGID

RIDGID OF25150A Operator's manual

Johnson Controls

Johnson Controls QUANTUM LX Setup

Sears

Sears Craftsman 919.167463 owner's manual

Ring Automotive

Ring Automotive RAC700 instructions