Celsi B-1005344 User manual

Page 1

16” XD Mk2 Inset Electric Fire

B-1005344

Packing Checklist

Electric Fire

Remote Control Handset

2 x AAA Batteries

Log Set

Ember Ice Crystal Set

Instruction Manual

Fascia

IMPORTANT

PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE

INSTALLATION AND USE OF THIS ELECTRIC FIRE AND RETAIN FOR

FUTURE REFERENCE.

This appliance is not intended for use by persons (including children) with

reduced physical, sensory or learning disabilities, or lack of experience

and knowledge, unless given supervision or instruction concerning use of

the appliance by a person responsible for their safety.

Page 2

IMPORTANT SAFETY ADVICE

WHEN USING AN ELECTRICAL APPLIANCE, BASIC PRECAUTIONS SHOULD ALWAYS BE

FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO

PERSONS, INCLUDING THE FOLLOWING IMPORTANT SAFETY ADVICE.

DO NOT cover or obstruct the airflow to the front of the heater. This is to avoid over-heating of

the product.

DO NOT leave the heater unattended while it is in use. Always turn the appliance to the OFF

position and switch off at the mains socket when not in use.

DO NOT leave children unsupervised whilst the appliance is switched on.

DO NOT operate this appliance with a damaged cord or plug, or after the appliance malfunctions,

has been dropped or damaged in any way.

DO NOT install a timer switch to operate the appliance.

DO NOT use this appliance as a freestanding appliance. It must always be securely fixed into a

Chimney breast opening.

DO NOT insert or allow objects to enter any ventilation or exhaust openings on the appliance. To

prevent a possible fire do not block air intakes or exhaust openings in any manner.

DO NOT place this appliance near flammable materials, surfaces or substances, as there may be

a risk of fire. Keep flammable materials, surfaces or substances at least 1 metre away from the

front of the product.

DO NOT switch on the fire if volatile vapours are present in the room.

DO NOT use this appliance in any areas where petrol, paint or other flammable liquids are stored

e.g. a garage or a workshop as the appliance contains components capable of producing a spark.

DO NOT let bare skin touch any hot surfaces to avoid burns and personal injury. The heater vent

will get hot when in use.

DO NOT use outdoors.

CAUTION- Some parts of this product can become hot and cause burns. Particular attention has

to be given where children and vulnerable people are present.

This appliance is for household use only

Page 3

Product Technical Data Sheet

Supplier Name / Trademark CELSI

Supplier Model Identifier B-1005344 ELECTRIFLAME XD Mk2 16”

Voltage 230v AC 50HZ

Fuse 13 Amp

Nominal Heat Output (Measured) 1.5 kW

Minimum Heat Output (Indicative) 0.75 kW

Maximum Continuous Heat Output 1.5 kW

Auxiliary Electricity Consumption at Nominal Heat Output 0.016 kW

Auxiliary Electricity Consumption at Minimum Heat Output 0.016 kW

Auxiliary Electricity Consumption at Standby Mode 0.0005 kW

Type of heat Output / Room Temperature Control With electronic room temperature

control plus week timer

Other Control Options With adaptive start control

Manufacturers Name and Address BFM Europe Ltd. Gordon Banks Drive, Trentham

Lakes, Stoke-on-Trent, Staffs, ST4 4TJ

Tel: 01782 339000

Page 4

Unpacking

Remove and discard the plastic bag.

Be responsible when handling the packing materials.

Keep the original packaging for future transportation and/or storage.

Check all accessories are removed from the packaging before storing it away for future use.

KEEP PLASTIC BAGS AWAY FROM CHILDREN!

Choosing a suitable location

This electric fire is designed to be fitted within a standard 16” x 22” fireplace opening which has a

minimum depth of 75 mm.

If the fire is installed within an existing chimney, this chimney must be dry and capped off using a

suitable chimney cap to avoid any damp.

The fire opening must have a level base so that when the fire is placed within the opening it is

stable.

Important Notice: To reduce heat losses and to prevent any chimney up draught

affecting the operation of your fire we recommend that the chimney is blocked off.

From the front of the fire ensure that there is a minimum clearance of 50mm between any

non-combustible materials. For combustible material clearances please consult with the

manufacturer.

If there is any doubt regarding the suitability of the installation site please contact your supplier

The fire can be connected direct or plugged into a mains socket which can be sited on the right-

hand side of the fire.

Ensure that the plug socket-outlet connection for this appliance is accessible. It MUST be readily

accessible for easy electrical isolation in the event of servicing and replacing components etc.

This appliance MUST NOT be located immediately below an electrical socket-outlet.

Page 5

Installation

Installation must be carried out by a qualified and competent person.

The fireplace opening size required to install the fire

Height: 545 –580mm

Width: 400 –460mm

Depth: 75mm minimum

Connect the appliance to single-phase AC supply of the voltage specified on the rating plate.

Should the fire be connected directly into the mains supply, then a fused switched spur with a 13-

amp fuse must be fitted. It is imperative that the power supply is capable of handling a load of

2000 watts (2kw). Do not use an extension lead.

This appliance must be earthed.

Allow sufficient flex to enable the fire to be removed from the opening.

Always ensure that all electrical work complies with the relevant Building Regulations

and the Electrical Code of Practice. All electrical work should be carried out by a

qualified electrician

Laying the Log & Embers

Using a screwdriver remove the 4 screws which holds the front glass in place, taking care remove

the glass from the fire and place in a safe place.

Sparingly lay some of the ember ice crystals along the rear of the fire bed as shown below

Page 6

Lay the logs over the ember ice crystals to create desired fuel bed effect as shown below and refit

the front glass using the 4 screws.

Arrange the remaining ember ice crystals along the front of the fire bed as shown below

Fitting the Fascia

The supplied fascia fits onto the front of the fire by either hooking the fascia brackets into the 4

slots on the outer trim of the appliance or by using the supplied magnets (method dependent on

model supplied)

Page 7

Operating the Fire

Manual Control

This appliance can be operated manually using the controls situated on the right-hand side of the

fire or by the included remote-control handset.

ON / OFF Power Switch

This switch is used to turn the mains supply to the appliance ON or OFF. When

the switch is in the ON position an indicator light located in the centre of the

screen will glow amber to indicate the appliance is switched on and in standby

mode. This needs to be in the ON position for both manual and remote

operation.

STANDBY

Used to switch appliance ON or OFF into standby mode.

FLAME

Pressing this button will cycle through the 4 different flame brightness levels.

HEATER

Use this button to select Low Heat, High Heat or heater OFF

When LOW heat is selected the indicator light will glow amber for 10 seconds.

When HIGH heat is selected the indicator light will glow red for 10 seconds.

Please note the heater will only operate when the room temperature is below

the temperature set on the handset, which can be adjusted using the

Temperature arrows on the Smart Control Panel. When the heater switches off

the fan will still continue to run for a short period to allow the appliance to cool

down.

BLUE

This button allows an additional blue flame effect to be switched on and off.

Page 8

Remote Control

Remove the battery / control panel cover by sliding completely down and insert 2 x AAA batteries

ensuring the batteries are fitted correctly. Refit the cover by sliding back up to the original

position. Please ensure old batteries are disposed of responsibly by contacting your local authority

about recycling schemes.

Ensure that the ON / OFF Power Switch on the fire is in the ON position.

Point the remote-control handset directly towards the fire and press the appropriate button to

operate the fire. Sliding the door down on the remote control will reveal the Smart Control panel

which offers additional functions. Otherwise using the basic remote buttons will operate the fire in

the same way as the manual control buttons with the exception of the blue flame function which

can only be operated manually on the fire.

Page 9

Smart Control functions

The Smart Control panel reveals additional buttons to allow the following functions

Set the Time of day

Thermostatic temperature adjustment from 16 to 30°C

Set 7-day timer with up to 3 programmable periods per day

Turn Adaptive Control On or Off

Turn Off and clear timer settings

Setting the Time

1. Press the SYNC button, which will start the day cursor to blink. Using the time arrow

buttons set to the current day e.g. Monday –1, Tuesday –2, Wednesday –3 etc. Press

SELECT to confirm the required day.

2. The hour setting will now be blinking, adjust using the time arrow buttons to the desired

hour and confirm using the SELECT button.

3. The minute setting will now be blinking, adjust using the time arrow buttons to the desired

minutes and confirm using the SELECT button.

Adjusting the desired temperature

Whilst the fire is switched on, use the Temperature Arrows to set the desired room

temperature. A confirmation beep will be heard from the fire. If the room is already warmer

than the temperature set then the heater will switch off until the thermostatic sensor

detects a fall in temperature.

Setting the Timer function

The timer function allows up to 3 timers to be programmed for use over a 7 day period.

1. Press the TIMER button to display the first timer, and then press the SELECT button to

adjust Timer 1 programme.

Set Time ON

2. The hour setting will now be blinking, adjust using the time arrow buttons to the desired

hour to switch on the fire and confirm using the SELECT button.

3. The minute setting will now be blinking, adjust using the time arrow buttons to the desired

minutes to switch on the fire and confirm using the SELECT button.

Set Days

4. The day cursor will now be blinking, use the time arrow buttons to highlight the required

day and press SET, additional days can be added using the time arrows and SET buttons.

If you add a day in error, select the day and press the CANCEL button to unselect. Only

when you have set all the days you require for the timer press SELECT to

confirm.

Set Time OFF (this must be at least 30 minutes after the ON time)

5. The hour setting will now be blinking, adjust using the time arrow buttons to the desired

hour to switch off the fire and confirm using the SELECT button.

6. The minute setting will now be blinking, adjust using the time arrow buttons to the desired

minutes to switch off the fire and confirm using the SELECT button.

7. A confirmation beep will be heard from the fire to confirm Timer 1 programme is now set.

Page 10

To set Timer 2 & 3 or alter timer programme.

8. Repeatedly pressing the TIMER button will cycle through the 3 available timer programmes

displaying the set parameters. To change or set an additional timer programme choose the

Timer number required and press the SELECT button.

9. Set the timer programme as before following steps 2 to 7.

Switch Off and clear Timers

When the timer icon is displayed on the remote-control handset the timer function is active. To

switch off the timer function and clear all timer programmes press the TIMER OFF button. A

confirmation beep will be heard from the fire.

Adaptive Control

Adaptive control works in conjunction with the timer programmes. When Adaptive Control is

turned ON the fire monitors the room temperature in relation to the selected target temperature.

If the room temperature is sufficiently lower that the selected temperature the Adaptive Control

facility will instruct the fire to switch on up to 10 minutes earlier than the set time to ensure the

room is at the required temperature at the set time.

IMPORTANT NOTE: If a confirmation beep is not heard after setting the timers or

adaptive control then turn the fire ON and OFF using the remote to ensure that the

latest settings have been sent to the fire. All settings will be lost from the fire if

disconnected from the mains or switched off at the fire power switch. Again, using the

remote to turn the fire ON and OFF will ensure the settings are sent to the fire.

This manual suits for next models

Table of contents

Other Celsi Indoor Fireplace manuals

Celsi

Celsi Electriflame VR EFVR40RE User manual

Celsi

Celsi Electriflame VR B-1005973 User manual

Celsi

Celsi ELECTRIFLAME XD 850HOW User manual

Celsi

Celsi Ultiflame Aleesia User manual

Celsi

Celsi B-1036317 User manual

Celsi

Celsi B-160940 User manual

Celsi

Celsi Electriflame User manual

Celsi

Celsi ELECTRIFLAME XD Mk2 B-1005344 User manual

Celsi

Celsi B-1001645 User manual

Celsi

Celsi B-1004554 User manual

Celsi

Celsi B-1036319 User manual

Celsi

Celsi Accent Infusion User manual

Celsi

Celsi ULTIFLAME B-1004553 User manual

Celsi

Celsi Electriflame VR 750 User manual

Celsi

Celsi CFECE0RE-ERP User manual

Celsi

Celsi B-1005975 User manual

Celsi

Celsi 16" Electriflame XD series User manual

Celsi

Celsi Electriflame VR Commodus S User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual