Cellink ANT465 User manual

INSTALLATION GUIDE

ANT465 15 ELEMENT

YAGI ANTENNA NEXT G

NOTE: cable must be kept clear of the reflector.

NOTE: Drain Hole must be on this side.

NOTE: These connectors must be covered with a waterproofing substance.

1/ Taking note of the antenna drain hole - slide the antenna Ubolts over the vertical boom

and tighten the nuts.

2/ Attach the feed cable (not supplied) to the antenna and run it down to the equipment.

Secure the cable to the vertical boom with cable ties (not supplied).

3/ Fit mating connector to the feed cable and attach test equipment. Check for a suitable

signal level.

If the signal level is unsatisfactory - loosen the angle adjustment screw on the angle

bracket and adjust the antenna angle for the best signal.

4/ Replace the angle adjustment screws and lock the antenna angle into place.

5/ Seal the connector union with a waterproofing compound. Vertical Mounting Boom

Ubolts

Waterproofing on connectors

NOTE: Cable must be kept in

close to the boom and clear of

the antenna elements.

Angle

adjustment

screw

20.0°

Email: [email protected]

Phone: 02-9716-0741 Fax: 02-9798-0017 Web: www.cellink.com.au

ANT465

-30

-25

-20

-15

-10

-5

010 20

100

110

120

130

140

150

160

170

180

190

200

210

220

230

240

250

260

270

280

290

300

310

320

330

340 350

ANT465

15 ELEMENT YAGI NEXT G

ANT 465 Yagi is designed for use in a Next G fixed site installation for

Wireless Voice / Broadband Data Access.

The antenna offers 15 dBi of gain across the band 824-894 MHz.

It comes angle adjustment bracket allowing +/-20 degrees of angle

adjustment in the Vertical plane. The bracket suits up to 50mm

mounting tube.

Electrical

Frequency:

Gain (dSi):

824-894 MHz

Mechanical

Construction: Welded Aluminium consrtuction.

Grey powder coated.

Tuned Bandwth:

Operating VSWR:

Input lmp:

Vertical Beamwth:

Horizontal Beamwth:

FJB Ratio:

• Reflector length.

Horizontal

71 MHz

<1.5:1

50 ohms (Nominal)

32 '

32'

18 dB

Length (m):

'Width (m):

Weight (kg):

Termination:

Projected Area.

Wind loading @160 KPH;

Mounting:

1.156

0.18

0.6

Cable tail with N-Type

Female Receptacle.

0.05008 SQM

6.08 KG

Angle Bracket suits

25-50mm T u bing

VerticalMHZ

20.0'

780 790 800 810 820 830 840 850 860 870 880 890 900 910

1.1

1.0

1.2

1.3

1.4

1.5

Email: [email protected]

Phone: 02-9716-0741 Fax: 02-9798-0017 Web: www.cellink.com.au

-30

-20

-15

-10

-5

010 20

100

110

120

130

140

150

160

170

180

190

200

210

220

230

240

250

260

270

280

290

300

310

320

330

340 350

-25

Other Cellink Antenna manuals

Cellink

Cellink AC-0442 User manual

Popular Antenna manuals by other brands

Alfa Network

Alfa Network APA-L01 Specifications

Naval

Naval PR-422CA Operation manual

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series manual

TERK Technologies

TERK Technologies TV44 owner's manual

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK quick start guide

HP J8999A instructions

MobilSat

MobilSat MSP-S Mounting instructions

Steren

Steren ANT-UHF 13 instruction manual

Novatel

Novatel 600-G User information

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna owner's manual

TRENDnet

TRENDnet TEW-AO12O Specifications

Radio Shack

Radio Shack 15-1837 owner's manual

CommScope

CommScope CMAX-OMFX-43M-I53 Installation instruction

Ramsey Electronics

Ramsey Electronics DAP25 Kit assembly and instruction manual

COBHAM

COBHAM SAILOR 800 VSAT Replacement procedure

Trango Systems

Trango Systems AD900-9 Specification sheet

Steren

Steren ANT-100 user manual

Proxim

Proxim 5054-PA-23 quick start guide