Celestron PowerSeeker 127EQ Specification sheet

Use the three tightening screws located at the

bottom of each leg to secure the extended legs

in place.

To set up the tripod, spread the legs outward

until they are fully extended. Extend the center

portion of each of the three tripod legs down 6-

8".

Item #31132

Quick Set-up Guide

123

All three legs should be the same length to

provide a level platform for the telescope.

Locate the equatorial mount and place the

base of the mount through the hole in the

center of the tripod mounting platform.

Properly assembled, the accessory tray should

appear as pictured above.

From underneath the tripod mounting platform,

thread the mounting bolt with washer into the

threaded hole on the bottom of the equatorial

mount.

Thread the latitude adjustment screw into the

equatorial mount until it is touching the inside

of the mount.

PowerSeeker 127

Your PowerSeeker 127 includes: optical tube w/

tube rings attached; tripod with center support

bracket; equatorial mount; two eyepieces; a 3x

barlow lens, finderscope; 5 lb. counterweight;

counterweight bar; two slow motion cables;

eyepiece accessory tray; The Sky™ CD software;

documentation including owner’s manual.

Item# 21049

Place the accessory tray on top of tripod's

center leg brace. Thread the tray into the

threaded hole in the center of the leg brace.

Questions or Problems with Set-up?

CONTACT:

Celestron Technical Support: 310.803.5955

For detailed usage information please

consult your owner’s manual.

Quick Set-up Guide [cont]

Locate the counterweight bar and

counterweight. Slide the counterweight half

way down the counterweight bar and tighten

the locking screw to secure in place.

Thread the threaded end of the counterweight

bar into the Dec axis of the equatorial mount.

The longer cable should attach to the Right

Ascension axis and the shorter cable attaches

to the Declination axis as shown above.

Before mounting the tube, remove the two

wingnuts on the tub rings.

Place the tube on the mount by lining up the

screws with the mounting holes on the mount.

Reattach both wingnuts and tighten to secure

in place.

17 18

Loosen the set screw on the focuser so that it

does not obstruct the inner diameter of the

focuser. Remove the plastic cap covering the

end of the focuser.

19 20

Locate the finderscope. Remove the knurled

nuts on the threaded posts at the focuser end

of the telescope tube.

Orient the finderscope so that the large lens is

facing towards the front of the tube. Place

finderscope over the posts on the tube and

tighten it down with the knurled nuts.

Remove the lens cap from the front of the

telescope. To observe, look through the

eyepiece as shown above.

For additional magnification, you can use the

included 3x barlow. Place the barlow in the

focuser in place of the eyepiece - remove the

cap from the barlow.

The focuser end of the telescope should be

over the counterweight assembly.

Slide the chrome end of the slow motion

control cables onto equatorial mount gear shaft

and tighten set screw to secure in place.

Insert the chrome barrel of the 20mm eyepiece

into the focuser and tighten the set screw.

Place the eyepiece into the barlow and tighten

the set screw to secure in place.

Other manuals for PowerSeeker 127EQ

This manual suits for next models

Other Celestron Telescope manuals

Celestron

Celestron NexStar 102 GT 102x1000 AZ User manual

Celestron

Celestron TrailSeeker User manual

Celestron

Celestron Regal M2 80ED User manual

Celestron

Celestron AstroMaster 130EQ User manual

Celestron

Celestron NexStar 8i User manual

Celestron

Celestron Ultima 52249 User manual

Celestron

Celestron NexStar SE Series User manual

Celestron

Celestron 12-36x50mm User manual

Celestron

Celestron 91073 User manual

Celestron

Celestron Tabletop 76 User manual

Celestron

Celestron 11007 User manual

Celestron

Celestron 21035 Travel Scope 70 User manual

Celestron

Celestron 22010 User manual

Celestron

Celestron SPC-80 User manual

Celestron

Celestron PowerSeeker 21041 User manual

Celestron

Celestron StarSense Explorer DOB User manual

Celestron

Celestron 21056-K User manual

Celestron

Celestron TRAVEL SCOPE 60 User manual

Celestron

Celestron EclipSmart TRAVEL SOLAR SCOPE User manual

Celestron

Celestron NexStar HC User manual

Celestron

Celestron Travel Scope 70DX User manual

Celestron

Celestron AstroMaster 90 EQ User manual

Celestron

Celestron C100ED-R User manual

Celestron

Celestron 80ED User manual

Popular Telescope manuals by other brands

Meade

Meade 81005 Condor instruction manual

Meade

Meade 114 EQ-DS instruction manual

Meade

Meade LX200 CLASSIC instruction manual

Leica

Leica 82 HD Specifications

EASTCOLIGHT

EASTCOLIGHT 9920 instruction manual

zoomion

zoomion Genesis 200 EQ instructions

TEC

TEC APO 140 owner's manual

Orion

Orion 7832 manual

Carson

Carson Skelescope SK-100 instruction manual

SKY-WATCHER

SKY-WATCHER VIRTUOSO instruction manual

Orion

Orion EZ Finder 7228 manual

cassini

cassini C-JRS operating instructions

nedis

nedis SCTE5060WT quick start guide

Meade

Meade Polaris 60EQ-D instruction manual

PlaneWave

PlaneWave CDK700 manual

William Optics

William Optics Synta Crayford user guide

Orion

Orion FUNSCOPE instruction manual

Levenhuk

Levenhuk Skyline Travel user manual