Casio QT-2100 User manual
QT-2100
Versatile IntelligentTerminal
———————————————————————
Installation &
Down Recovery Manual
Version 1.0 February 2002
c
C
7
4
1
0
8
5
2
00
9
6
3
•
QT-2100
Contents
I-2
This manual is intended for use as a reference to the QT-2100 system. It provides details to
install systems and down recovery. This manual does not describe actual programming,
which is covered in the QT-2100 programming manual.
This manual consists of the following chapters:
1. System installation
This chapter show the procedure of installing QT-2100 systems.
2. System down and recovery
This chapter explains actions to take and recovery methods when the system goes down.
Note: Casioreservestherighttochangeequipmentandspecificationswithoutobligationand
notification. The terms used in this manual may be different from those used in other
manuals of Casio’s products.
Printing history
Manual version Software version
Version 1.0: February, 2002 First Edition: February, 2002 Version 1.0
Revised points
I-3
QT-2100Installation&DownRecoveryManual
Contents
I-4
I-5
QT-2100Installation&DownRecoveryManual
1. System installation........................................................................................I-6
1-1. How to load IPL (Initial Program Loading) ..................................................................I-6
1-1-1. From PC to QT-2100 terminal via RS-232C.....................................................I-6
1-1-2. From one QT-2100 to QT-2100 terminals via inline .........................................I-7
1-1-3. From CF card to QT-2100 terminal ..................................................................I-7
1-2. How to install QT-2100 system...................................................................................I-8
1-2-1. QT-2100 stand alone system (with printer) ......................................................I-8
1-2-2. QT-2100 master/satellite system (with local printer) ........................................I-8
1-2-3. QT-2100 master/satellite system (with remote printer).....................................I-9
1-2-4. Printer DIP switch configuration .....................................................................I-10
2. System down and recovery........................................................................I-11
2-1. Measures to prevent trouble.....................................................................................I-12
2-2. Master terminal failure ..............................................................................................I-13
2-2-1. Check tracking master terminal failure ...........................................................I-13
2-2-1-1. Detection of check tracking master terminal failure........................................I-13
2-2-1-2. Master failure during check tracking operation...............................................I-14
2-2-2. Remote printer failure.....................................................................................I-15
2-2-2-1. Detection of remote printer failure..................................................................I-15
2-2-2-2. Master printer failure during printing on remote printer ..................................I-15
2-3. Recovery processing ................................................................................................I-16
2-3-1. Master/backup master down detection...........................................................I-16
2-3-2. When both master and backup master go down............................................I-16
2-4. Master failure during X/Z collection/consolidation or terminal data transfer .............I-16
2-5. Satellite terminal down..............................................................................................I-16
I-6
System Installation
1. System installation
In this chapter shows how to install QT-2100 systems and peripherals.
1-1. How to load IPL (Initial Program Loading)
Normally,IPL isnot necessarysince QT-2100has efficientprogram options tomeet your
circumstances.
Insome cases, youneedto change theapplicationprogram tomeet yourrequirements,the
IPL is necessary to download the application program to QT-2100.
To load IPL, there are three methods:
1) From PC to QT-2100 terminal via RS-232C
2) From one QT-2100 terminal (master) to QT-2100 terminals (satellite) via inline
3) From CF card to QT-2100 terminal
1-1-1. From PC to QT-2100 terminal via RS-232C
1. Set up the system (refer to the left figure).
2. Initialize the target QT-2100 to receive the IPL data (refer to
the Machine initialization section of the Manager operation
chapter of QT-2100 Reference manual page 95).
3. Run the loading program of PC.
4. After IPL completion, continue to the initialize operation.
QT2100
PC
IPL source
IPL target
COM 1
COM
port
IPL Data
I-7
QT-2100Installation&DownRecoveryManual
1-1-2. From one QT-2100 to QT-2100 terminals via inline
1. Set up the system (refer to the left figure).
2. Initialize the target QT-2100 to receive the IPL data (refer to
the Machine initialization section of the Manager operation
chapter of QT-2100 Reference manual page 95.)
3. ExecuteIPLdatasendingoperation(refertotheAuto-program
operation section of the Manager operation chapter of QT-
2100 Reference manual page 125.)
4. After IPL completion, continue to the initialize operation.
IPL source
IPL Data
In-line
QT2100
QT2100
IPL target In-line (CASIO original cable or CAT5 cable)
QT2100QT2100QT2100
1-1-3. From CF card to QT-2100 terminal
1. Insert the CF card to the CF card slot of the target terminal.
2. Initialize the target QT-2100 to receive the IPL data (refer to
the Machine initialization section of the Manager operation
chapter of QT-2100 Reference manual page 95.)
3. Execute IPL data receiving operation (refer to the Machine
initialization section of the Manager operation chapter of QT-
2100 Reference manual page 125.)
4. After IPL completion, continue to the initialize operation.
QT2100
CF card
I-8
System Installation
1-2. How to install QT-2100 system
1-2-1. QT-2100 stand alone system (with printer)
1. Set up the system (refer to the left figure).
2. Initialize the QT-2100 (refer to the Initialization chapter of
QT-2100 Programming manual page 8.)
Note 1:
If the QT-2100 cannot recognize the printer(s) correctly,
check the dip switches on the printer or printer cable and
tryinitializationoperationagain.Casioprintercable(PRT-
CB-8A/-8B) is required for proper recognition of the local
printer.
Note 2:
If the Slip printer is connected to COM 4, 5, or 6 port,
automatic printer detection during initialization is not
made. In this case, program the I/O parameter file manu-
ally and flag clear the machine.
3. Complete the initialize operation.
1-2-2. QT-2100 master/satellite system (with local printer)
1. Set up the system (refer to the figure below).
2. Initialize the master QT-2100 (refer to the Initialization chap-
ter of QT-2100 Programming manual page 8.)
Note 1:
1. Do not turn on other QT-2100.
2. If the QT-2100 cannot recognize the local printer(s) cor-
rectly, check the dip switches on the printer or printer
cable and try initialization operation again. Casio printer
cable(PRT-CB-8A/-8B)isrequiredforproperrecognition
of the local printer.
Note 2:
If the Slip printer is connected to COM 4, 5, or 6 port,
automatic printer detection during initialization is not
made. In this case, program the I/O parameter file manu-
ally and flag clear the machine.
QT2100
R/J
Slip
In-line (CASIO original cable/CAT5 TUP cable)
QT2100QT2100QT2100
R/J R/J
R/J R/J
R/J R/J
PRN (1)... PRN (3) PRN (1)...PRN (3) PRN (1)...PRN (3)
PRN (1)
QT2100
R/J
Slip
R/J
PRN (1)...PRN (3)
I-9
QT-2100Installation&DownRecoveryManual
3. Initialize QT-2100 terminals one by one.
Note:
When you want to copy master program to satellites,
completethemasterprogram,andtheninitializethesatel-
lite and receive the master program during initialization
procedure of satellites.
1-2-3. QT-2100 master/satellite system (with remote printer)
1. Set up the system (refer to the figure below).
2. Initialize the master QT-2100 (refer to the Initialization chap-
ter of QT-2100 Programming manual page 8.)
Note 1:
1. Do not turn on other QT-2100.
2. If the QT-2100 cannot recognize the local printer(s) cor-
rectly, check the dip switches on the printer or printer
cable and try initialization operation again. Casio printer
cable(PRT-CB-8A/-8B)isrequiredforproperrecognition
of the local printer.
Note 2:
If the Slip printer is connected to COM 4, 5, or 6 port,
automatic printer detection during initialization is not
made. In this case, program the I/O parameter file manu-
ally and flag clear the machine.
3. Initialize QT-2100 terminals one by one.
Note:
When you want to copy master program to satellites,
complete the master program first, and then initialize the
satellites and receive the master program at the end of
initialization procedure of satellites.
4. Declareremoteprinterbyprogrammingtheprinterconnection
table to all terminals in the system (refer to the Programming
printer connection section in the Program 3 chapter of the
Programming manual page 70.)
QT2000
R/J
Slip Slip
Slip
In-line
QT2000QT2000QT2000 RP
RP
RP
R/J
PRN (1)...PRN (3)
PRN (1)...PRN (3)
I-10
System Installation
SW No. Function
Data reception error
Receive buffer capacity
Handshaking
Data word length
Parity check
Parity selection
Transmision speed
ON OFF
Ignored Prints "?"
45 bytes 4k bytes
XON/XOFF DTR/DSR
7 bits 8 bits
Yes No
Even Odd
See transmission
speed setting
Density setting
Light
Dark
SW No.
3
ON
OFF
ON
OFF
4
ON
OFF
OFF
ON
UP-350 Bottom view
DSW1 DSW2
1
2
3
4
5
6
7
8
1
SW No. Function
Busy condition
Reserved
Print density
Reserved
Reserved
I/F 6 pin reset signal
I/F 25 pin reset signal
ON OFF
Buffer full Buffer full
or Offline
Fixed
See density setting
Fixed
Fixed
Enabled Disabled
Enabled Disabled
1
2
3
4
5
6
7
8
2
Transmission
speed setting
bps
2400
4800
9600
19200
SW No.
7
ON
OFF
ON
OFF
8
ON
ON
OFF
OFF
SW No. Function
Data word length
Parity check
Parity type
Data tranfer rate
Connection of
customer display
Data reception error
Hand shake
ON OFF
7 bit 8 bit
Yes No
Even Odd
See data transfer
rate setting
Connected Not
connected
Ignored Print "?"
XON/XOFF DTR/DSR SA-3015 Bottom view
DSW1 DSW2
1
2
3
4
5
6
7
8
1
SW No. Function
Automatic CR
Reception buffer size
Font selection
Carriage speed
Busy condition
Internal use
I/F 6 pin reset signal
I/F 25 pin reset signal
ON OFF
AlwaysYes Always No
32 bytes 2048 bytes
9 x 9 7 x 9
Low High
Buffer full Buffer full
or Offline
Fixed
Enabled Disabled
Enabled Disabled
1
2
3
4
5
6
7
8
2
Data tranfer
rate setting
bps
1200
2400
4800
9600
SW No.
4
ON
OFF
ON
OFF
5
ON
ON
OFF
OFF
1-2-4. Printer DIP switch configuration
UP-350
SA-3015
SW No. Function
Data reception error
Receive buffer capacity
Handshaking
Data word length
Parity check
Parity selection
Baud rate
Busy condition
ON OFF
Ignored Prints "?"
40 bytes 1k byte
XON/XOFF DTR/DSR
7 bits 8 bits
Yes No
Even Odd
4800 bps 9600 bps
Buffer full Buffer full
or Offline
1
2
3
4
5
6
7
8
1
SW No. Function
No. of digits
(7x9 font / 9x9 font)
Internal use
#6 pin reset signal
#25 pin reset signal
ON OFF
42 / 35 40 / 33
digits digits
Enabled Disabled
Enabled Disabled
1
2
3
4
2
UP-250
Dip switch is located at the bottom of the printer.
Other manuals for QT-2100
5
Table of contents
Other Casio Touch Terminal manuals
Casio
Casio V-R100 User manual
Casio
Casio DT-940 User manual
Casio
Casio QT-6000 User manual
Casio
Casio QT-6600 User manual
Casio
Casio IT-9000C User manual
Casio
Casio IT-800 Series User manual
Casio
Casio DT-X100 Series User manual
Casio
Casio IT-G600 Series User manual
Casio
Casio V-REGI Series User manual
Casio
Casio IT -G500 Series User manual
Casio
Casio V-REGI Series User manual
Casio
Casio QT-6600 Owner's manual
Casio
Casio ET-L10 Series User manual
Casio
Casio DT-X8-20C-CNV User manual
Casio
Casio DT-X11 Series User manual
Casio
Casio IT-10M20 User manual
Casio
Casio IT-600M30 User manual
Casio
Casio DT-X400 Series User manual
Casio
Casio DT-X10 series User manual
Casio
Casio V-REGI Series User manual
