CARVIN Vintage 16 User manual

- 1 -

How to bias:

Vintage 16

Rev C

6/27/2012

carvinservice.com

- 2 -

Only a certified technician should bias Carvin amps, this is very

dangerous, you can get hurt, please be very careful when working

with any tube amp!

If you have changed the tubes make sure they are a matched set. (2) EL84

- The Bias for the Vintage 16 should be 40mA at Power Mode to Normal setting,

with 120VAC.

STEP 1

These are the tools you will need:

1. A flat head screw driver

“small”.

2. A multi-meter, w/ milli amp

reading.

3. Banana to clip leads.

4. Amp stand (optional).

STEP 2

Take the amp out of the amp

enclosure (cabinet). Set it in an amp

stand. Be very careful with the tubes

they can break.

NOTE: If you don't have an amp

stand then support the chassis on

some blocks of wood so that the

power tubes are not touching

anything - they get very hot!

- 3 -

STEP 3

Set the switch to “Internal Load”

IMPORTANT: Do NOT turn on the

amplifier without a speaker plugged

in!", when in 8 or 16 Ohm setting.

STEP 4

Make sure you set the switch in the

back to Normal; if you don’t set it to

“Normal” the bias will not be the true

reading.

STEP 5

A) Lower the volume.

B) Unplug your guitar cord from the

input of the amp.

NOTE: If you have signal going

through the amp, it will not be the

true reading, when you set the bias.

- 4 -

STEP 6

A) Connect the leads to the meter. B) Set your meter to the milliamp (MA) position.

Make sure the fuse inside is good.

NOTE: If the Fuse inside your meter is open, the meter will never work. It will

always read 0mA. In the meter above, mA and COM is selected, you have the

option to plug in the lead on (A) but because the setting will be set to 100mA it is

best to use mA.

STEP 7

Move the wire connected to QC2 to the QC9 spade

connector. In doing this you are opening the circuit so

that you can measure the current across it.

Note how in step 8 (pictures) the wire is already moved.

STEP 8

1. 2.

- 5 -

Connect clips from meter to spade connectors. One of the clips to QC2 and the

other clip to QC9.

IMPORTANT: Never power the amp ON before connecting the leads, you will

get a big spark, you may blow the fuse of the Meter and or damage the amp.

STEP 8

Plug in AC Cord.

NOTE: Sometimes when the AC Cord

is new it does not want to go in all the

way. Push firmly to force it in, if that is

the case.

STEP 9

Turn the Power Button ON. Wait 2

minutes for the amp to get hot, after the

2 minutes you should see the meter read

current. It will start slow then increase

up to 40mA, adjust it accordingly.

- 6 -

STEP 10

Check your meter at this point, if it goes

over 40mA, lower it by turning the bias

potentiometer with the screw driver,

clock wise, if it’s under 40mA bring it

up by turning the potentiometer the

other way.

It is OK and normal for the bias reading

to fluctuate a little bit and may not be

exactly 40mA but as close as possible.

IMPORTANT: I was using a current shunt to measure the current, that’s why the

pictures below shows mV, your meter should read (mA).

Good Bias High Bias Low Bias

STEP 11

Power down Steps:

1. Turn OFF the amp

2. Disconnect the meter leads.

3. Unplug your AC cord and wait for the tubes to cool down, so that you can put the

amp back in the cabinet.

4. Move the wire connected to QC9 back to QC2.

IMPORTANT: During biasing and normal amp operation if there is a burning smell

or loud crackling noise that comes from the speaker, you should turn off the amp as

your may have a bad tube. The same is true if your meter reads higher that 150mA

or goes into overload. The tubes should never glow RED on the gray plate material,

- 7 -

the largest metal part inside the tube. This indicates a major problem and extremely

unsafe condition. If this happens turn off the amp immediately!

IMPORTANT: The tubes get very hot! Don’t touch them, you will burn your

skin if you do. If the amp is ON the tubes will get hot, even if you are not

playing the amp, wait 30 minutes before handling the unit to ensure the amp

cooled down.

IMPORTANT: This is not the only way to set the bias on this amp, this is the

Carvin Approved method which is used on the Production line in the San Diego,

California Factory.

NOTE: If the tubes are getting hot and 3 to 5 minutes went by and you don’t see

any reading on your meter check your meter, you may have the leads plugged into

the wrong place in your meter or the fuse of your meter is open.

EXPORT(230-240VAC 50Hz): Follow the same instructions.

www.carvinservice.com

Comments or questions email us at Carvinservice@carvin.com

This manual suits for next models

3

Table of contents

Popular Amplifier manuals by other brands

ASTRO

ASTRO HVO V40 P operating manual

Marantz

Marantz SUPERSCOPE BLA-545 Service data

NAD

NAD CI980 Quick setup guide

Technics

Technics SE-CH770 Service manual

Harman Kardon

Harman Kardon HK6300 instruction manual

NAD

NAD T975 owner's manual

McIntosh

McIntosh MA6850 Brochure & specs

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N manual

Viatron

Viatron Autrix Technical manual

GME

GME GA9800 instruction manual

Atlas

Atlas CP700 Specification sheet

Roland

Roland KC-1000 owner's manual

Pyle

Pyle PFMRA350BW user manual

Advantage

Advantage S-250 manual

IRT Electronics

IRT Electronics DVA-3007 manual

Dimavery

Dimavery BA-100 Series user manual

Sony

Sony XM-S400D operating instructions

Schertler

Schertler ROY X quick guide