Caple AS610BK User manual
Instruction manual for wall chimney hoods
Model codes: AS610BK / AS910BK
Contact Caple on 0844 800 3830 or for spare parts www.4caple.co.uk
1. For ease of installation, the light assembly should be fitted using a magnetic
screwdriver before the hood is installed on the wall.
2. The plastic cover is to protect the light assembly in transit. Once the light is
fitted to the hood, the plastic cover is easily removed by slackening the screws
and pulling the cover off.
4. For ease of installation, the light assembly should be fitted using a magnetic
screwdriver before the hood is installed on the wall.
5. The plastic cover is to protect the light assembly in transit. Once the light is
fitted to the hood, the plastic cover is easily removed by slackening the screws
and pulling the cover off.
Installing the Ductwork
1. Plan where the ductwork will run between the hood and the outside. The
hoods exhaust vertically but can be ducted to the rear behind the chimney
duct through an outside wall or vertically up through the ceiling to the
roof. A short straight duct run will produce the most air flow. Length and
elbows will reduce the efficiency of the blower.
2. Install a roof or wall cap. Connect a 6 round metal duct to the cap and
work backwards toward the hood. Ensure joints are completely sealed
with duct tape.
Fixing to the Wall
1. Before mounting the hood, plug in and test all functions for correct operation.
2. Remove the filters from the bottom of the hood to pre vent damage during the installation.
3. With assistance, hold the hood temporary in position ensuring the bottom is above the minimum clearance for
the cooking surface. Mark on the wall the holes for the two mounting screws.
4. Drill the holes and install the mounting bracket (1) . Use the appropriate screws and screw anchors for your
wall type (e.g. reinforced concrete, drywall, etc.). If necessary, prepare back wall with cross framing for secure
installation.
5. Mount the hood onto the bracket (2).
Connect a 6 aluminum duct tube (not included) to the exhaust piece using duct tape on all seals. (C)
7.
to roof cap
to wall cap
hood
decorative
chimney duct
38
39
40
Mounting bracket
Hook
1
2
mushroom tapping screw
3
6. Install two mushroom tapping screw into the wall.
Installing Guideline
Wall Mounted-Duct-out
1200~1700mm
650~700mm
Note:The above installation guideline for references only , please contact your local dealer
for a installation service.
Fixing the Decorative Chimney
Flu
1
2
3
.
.
.
Carefully losen but do not separate the telescopic chim ney duct pieces.
Arrange the electrical power supply within the dimen sions of the
decorative chimney duct.
Adjust the width of the support bracket to match the upper duct. Fix it
to the ceiling using the screws (B) so that it is centered in line with your
hood and at a distance from the ceiling indicated.
C
1. Separate lamp cover and left bracket by unscrewing.
2. Install right bracket to the cooker hood, then tighten the screws.
3. Connect two cables.
4. Re-Install left bracket and tighten the screws.
This manual suits for next models
1
Table of contents
Other Caple Ventilation Hood manuals
Caple
Caple GC100SS User manual
Caple
Caple bu521 User manual
Caple
Caple BUCH User manual
Caple
Caple ZEL900 User manual
Caple
Caple use and maintenance Parts list manual
Caple
Caple BXI1050SS User manual
Caple
Caple VIE550BK User manual
Caple
Caple BUCHB User manual
Caple
Caple DD940BK User manual
Caple
Caple DD903BK User manual
Caple
Caple BXI910 User manual
Caple
Caple DD912BK User manual
Caple
Caple DDMEXT4 User manual
Caple
Caple FSCHSS9 User manual
Caple
Caple CHIMNEY SB XC600SS User manual
Caple
Caple CCH600 User manual
Caple
Caple CE1121 User manual
Caple
Caple DD911BK User manual
Caple
Caple FSCHSS7 User manual
Caple
Caple CE920WH User manual
