Canon MLT (S) User manual
Before using the instrument, be sure to read this manual thoroughly.
Also, read the manuals of other instruments in this system.
Keep the manual where it is easily accessible.
User’s Manual
MLT (S)
CXDI Image Processing Software
Please Note
1. In no event will Canon be liable for direct or indirect consequential damage arising out of the use of this
product. Canon will not be liable for loss of image data due to any reason.
2. Please have this product installed by Canon representative or distributor.
3. Canon reserves the right to change the specifications of the product without prior notice.
© CANON INC. 2009
All rights reserved.
Under copyright laws, this manual may not be copied, in whole or in part, without the written consent of
Canon.
Contents
1. Overview ..................................................................................................... 1
1.1 About MLT (S) ........................................................................................................... 1
1.2 Available Functions of MLT (S) ................................................................................. 2
2. Edit Exposure Mode Settings ...................................................................... 3
2.1 Procedures to Set Exposure Mode ........................................................................... 3
2.2 Setting Enhancement ................................................................................................ 7
2.3 Setting Noise Reduction ............................................................................................ 8
2.4 Setting Dynamic Range Adjustment ......................................................................... 9
2.4.1 Setting high-density sections ............................................................................. 9
2.4.2 Setting low-density sections ............................................................................. 10
3. QA Mode Settings ..................................................................................... 11
3.1 Procedures to Change Parameters ......................................................................... 11
3.2 Changing Enhancement .......................................................................................... 14
3.3 Changing Noise Reduction ..................................................................................... 15
3.4 Changing Dynamic Range Adjustment ................................................................... 16
3.4.1 Changing high-density sections ....................................................................... 16
3.4.2 Changing low-density sections ........................................................................ 17
4. QA Parameters ......................................................................................... 18
Notation Conventions
Notation 1
In this manual, the name of button is enclosed with a pair of brackets [ ], and the buttons that are selected in succession
are connected with > to indicate the order.
Example: On the Exposure screen, touch the followings:
[SYSTEM] > [EDIT EXPOSURE MODE]
Notation 2
If any detailed explanation for the operation or setting is available on other page in this manual, the page to refer is indi-
cated with (→page number).
Example: Please set the parameters by referring to 2.2 Setting Enhancement (→P. 7 ) .
Notation 3
When description of the procedure or setting continues from an odd-numbered page (right page) to the subsequent even-
numbered page (left page), a small note, [Continued on the following page »] appears at the bottom-right of the odd-
numbered page to draw your attention.
– 1 –
1. Overview
1.1 About MLT (S)
NOTE: This user’s manual is for version 7.1 and later of the CXDI System Software.
The CXDI Image Processing Software MLT (S) (called “MLT (S)” in this manual) is
designed to extend the image processing functions provided with the CXDI series of Canon dig-
ital radiography system (called “CXDI” in this manual).
By installing MLT (S) on the Control PC, the advanced image processing features of MLT (S)
are brought into full scope both in the Edit Exposure Mode and QA Mode.
QA Mode Screen Extended by MLT (S) (ENHANCEMENT Tab)
QA Mode Screen Extended by MLT (S) (DYNAMIC RANGE Tab)
1.Overview
– 2 –
1.2 Available Functions of MLT (S)
This manual describes the operating procedures of the following image processing function that
is available with MLT (S). For details and information on other image processing functions,
please refer to Operation Manual and Setup Guide.
Enhancement
This accentuates edge details and local contrast of the exposure image for improving
sharpness.
The degree of enhancement can be adjusted by setting the edge enhancement parameters.
The frequency band for edge enhancement can also be modified by setting the edge
frequency parameters.
The degree of enhancement of the local contrast can be adjusted by setting the contrast
boost parameters.
Noise Reduction
This reduces noise in the exposure image for improving granularity.
The EFFECT parameter setting can be used to adjust the degree of noise reduction.
Dynamic Range Adjustment
This improves the detectability of high-density and low-density areas in the exposure
image.
The settings for the maximum density parameter and minimum density parameters can
be used to adjust the dynamic range.
NOTE: The effects resulting from changes to the parameters may be difficult to check
in the exposure image of the QA mode screen.
In these cases, check by touching [MAG.] or [QA-MAG.] to display the
enlarged screen.
Continued on the following page >>
– 3 –
2. Edit Exposure Mode Settings
2.1 Procedures to Set Exposure Mode
1Display the Edit Exposure Mode screen
On the Exposure screen, touch the followings:
[SYSTEM] > [EDIT EXPOSURE MODE]
Edit Exposure Mode Screen
2Select the Sensor Unit
If two or more sensor units are being used in the system, touch the Sensor Unit button,
then select the Sensor Unit.
3Select the Category tab
If eight or more categories are registered in the system, touch the or button to dis-
play the Category tabs that are not currently visible.
Sensor Unit
Button
Button
Button
Category Tab Exposure Mode
2.Edit Exposure Mode Settings
– 4 –
4Select the Exposure Mode
Make sure that [EDIT PARA.] at the top-left is displayed in highlight, then select the
desired Exposure Mode.
The EDIT PARA. screen appears.
EDIT PARA. Screen (PREVIOUS PAGE)
5Display the next page
Touch [NEXT PAGE].
EDIT PARA. Screen (NEXT PAGE)
This manual suits for next models
2
Table of contents
Other Canon Software manuals
Canon
Canon Optura 200 MC User manual
Canon
Canon EOS Rebel T3 18-55mm IS II Kit User manual
Canon
Canon EOS-1D User manual
Canon
Canon SD30 - PowerShot Digital ELPH Camera User manual
Canon
Canon Microfilm Scanner 800II User manual
Canon
Canon Elura 60 - Elura 60 MiniDV Camcorder User manual
Canon
Canon PowerShot G10 - Digital Camera - Compact Safety guide
Canon
Canon WebView LivescopeMV User manual
Canon
Canon 3211B001 - PowerShot E1 Digital Camera Mounting instructions
Canon
Canon 40MC - Elura MiniDV Digital Camcorder User manual
Canon
Canon CanoScan D646U User manual
Canon
Canon EOS 5D - Focusing Screen Ee-A User manual
Canon
Canon DV-PC Mounting instructions
Canon
Canon Networked Multi-Projection Setup guide
Canon
Canon EOS 60D User manual
Canon
Canon Optura 30 - Optura 30 MiniDV Camcorder User manual
Canon
Canon PowerShot A520 User manual
Canon
Canon HG-10 User manual
Canon
Canon EOS 5D Mark II - EOS 5D Mark II 21.1MP Full Frame CMOS Digital SLR... User manual
Canon
Canon PowerShot A550 User manual
