Canon FINISJER-E1 User manual

1999 CANON INC. CANON FINISHER-E1 REV.0 JAN. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

REVSION 0

FY8-13FU-000

FINISHER-E1

JAN. 1999

1999 CANON INC. CANON FINISHER-E1 REV.0 JAN. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

IMPORTANT

THIS DOCUMENTATION IS PUBLISHED BY CANON INC., JAPAN, TO SERVE AS A SOURCE

OF REFERENCE FOR WORK IN THE FIELD.

SPECIFICATIONS AND OTHER INFORMATION CONTAINED HEREIN MAY VARY SLIGHTLY

FROM ACTUAL MACHINE VALUES OR THOSE FOUND IN ADVERTISING AND OTHER

PRINTED MATTER.

ANYQUESTIONSREGARDINGINFORMATION CONTAINED HEREINSHOULD BEDIRECTED

TO THE COPIER SERVICE DEPARTMENT OF THE SALES COMPANY.

THIS DOCUMENTATION IS INTENDED FOR ALL SALES AREAS, AND MAY CONTAIN INFOR-

MATION NOT APPLICABLE TO CERTAIN AREAS.

Printed in Japan

Imprimé au Japon

Use of this manual should be strictly su-

pervised to avoid disclosure of confidential

information.

Prepared by

OFFICE IMAGING PRODUCTS TECHNICAL SUPPORT DIVISION

OFFICE IMAGING PRODUCTS QUALITY ASSURANCE CENTER

CANON INC.

5-1, Hakusan 7-chome, Toride-shi, Ibaraki, 302-8501 Japan

1999 CANON INC. CANON FINISHER-E1 REV.0 JAN.1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

This Service Manual contains basic data and figures for the Finisher-E1 needed to

service the machine in the field.

Chapter 1 General Description introduces the finisher's features, specifications, and

names of parts, and shows how to operate the finisher.

Chapter 2 Basic Operation discusses the principles of operation used for the finisher's

mechanical and electrical systems. It also explains the timing at which these

systems are operated.

Chapter 3 Mechanical System discusses how the finisher is constructed mechanically,

and shows how it may be disassembled/assembled and adjusted.

Chapter 4 Maintenance and Inspection provides tables of periodically replaced parts and

consumables and durables, together with a scheduled servicing chart.

Chapter 5 Troubleshooting provides tables of maintenance/inspection, standards/

adjustments, and problem identification (image fault/malfunction).

Appendix contains diagrams showing electrical parts arrangement, tables of

signals, tables of special tools, tables of solvents/oils, and a general timing

chart.

For installation, see the Installation Procedure that comes with the finisher.

The descriptions in this Service Manual are subject to change without notice for

product improvement or other purposes, and major changes will be communicated in the

form of Service Information bulletins.

All service persons are expected to have a good understanding of the contents of this

Service Manual and all relevant Service Information bulletins and be able to identify and

isolate faults in the machine.

INTRODUCTION

1999 CANON INC. CANON FINISHER-E1 REV.0 JAN.1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

iii

CONTENTS

I. FEATURES ..................................1-1

II. SPECIFICATIONS........................1-2 III. OPERATING THE MACHINE.......1-6

IV.

MAINTENANCE BY THE USER ..

1-11

I. BASIC CONSTRUCTION ............2-1

II. BASIC OPERATIONS ..................2-6

III. FEEDING DRIVE SYSTEM .........2-9

IV. INTERMEDIARY PROCESSING

TRAY ASSEMBLY ..................... 2-11

V. STAPLING ................................. 2-42

VI. OPERATIONS OF THE STACK

TRAY ......................................... 2-45

VII. DETECTING JAMS................... 2-53

VIII.POWER SUPPLY ...................... 2-58

CHAPTER 3 MECHANICAL SYSTEM

CHAPTER 2 BASIC OPERATION

CHAPTER 1 GENERAL DESCRIPTION

I. EXTERNALS AND CONTROLS..3-1

II. FEEDING SYSTEM .....................3-6

III. PROCESSING TRAY ...................3-7

IV. RETURNING ROLLER ............. 3-16

V. STACK TRAY............................. 3-24

VI. STACK TRAY LIFTER UNIT...... 3-25

VII. STAPLER .................................. 3-35

VIII.PCBs ......................................... 3-36

CHAPTER 4 MAINTENANCE AND INSPECTION

I. PERIODICALLY REPLACED

PARTS .........................................4-1

II. CONSUMABLES AND

DURABLES..................................4-1

III. SCHEDULED MAINTENANCE ...4-1

1999 CANON INC. CANON FINISHER-E1 REV.0 JAN. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 5 TROUBLESHOOTING

APPENDIX

I. ADJUSTMENTS ..........................5-1

II. ARRANGEMENT OF ELECTRICAL

PARTS ...................................... 5-12

A. SIGNALS AND

ABBREVIATIONS........................ A-1

B. GENERAL TIMING CHART ........ A-3

C. GENERAL CIRCUIT DIAGRAM . A-5

III. TROUBLESHOOTING .............. 5-15

IV. SELF DIAGNOSIS .................... 5-19

D. FINISHER CONTROLLER

CIRCUIT DIAGRAM.................... A-6

E. SOLVENTS AND OILS ............. A-15

1999 CANON INC. CANON FINISHER-E1 REV.0 JAN. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 1

GENERAL DESCRIPTION

I. FEATURES ..................................1-1

II. SPECIFICATIONS........................1-2 III. OPERATING THE MACHINE.......1-6

IV. MAINTENANCE BY THE

USER ........................................ 1-11

CHAPTER 1 GENERAL DESCRIPTION

1999 CANON INC. CANON FINISHER-E1 REV.0 JAN.1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

1-1

I. FEATURES

1. Small in Size, Light in Weight

• The finisher is designed as a small, light delivery device.

2. Mono-Frame

• The finisher is cased in a mono-frame, which has enabled reduction of the number of covers.

3. Sorting and Stapling by Stack Offset

• The finisher puts together stacks of sheets on its intermediary processing tray for offset

sorting and stapling.

4. Stack Tray

• The finisher’s stack tray is capable of holding as many as 1,000 sheets of small-size paper or

15 sheets of large-size paper.

Further, it can hold as many as 30 sets of stapled stacks (each consisting of up to 30 sheets).

CHAPTER 1 GENERAL DESCRIPTION

1999 CANON INC. CANON FINISHER-E1 REV.0 JAN. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

1-2

II. SPECIFICATIONS

A. Specifications

Description

Stack tray (tray lift mechanisms, with intermediary tray fixed in position)

Face-down stacking

Face-up stacking (1-to-n mode)

A3, A4, A4R, A5, A5R, B4, B5, B5R, postcard

279x432 mm (11"x17"), LGL, LTR, LTRR, STMT, STMTR

64 to 128 g/m2

Stack tray 1

Intermediary processing tray 1

Staple stacking

Non-staple stacking

Non-staple offset stacking

Small-size

Medium-/large-size

Small-size*1

Medium-size*2

Large-size*3

139.7 to 297 mm

210 to 297 mm (stapling not available for A5)

A3, A4, A4R, A5, A5R, B4, B5, B5R

279 x 432 mm (11" x 17"), LGL, LTR, LTRR, STMT, STMTR

A3, A4, A4R, B4, B5

279 x 432 mm (11" x 17"), LGL, LTR, LTRR

210 to 297 mm

20 mm

Item

Stacking

Stacking mode

Stack paper size

Paper weight

Bins

Modes

Stack tray

capacity

Stacking

width*4

Stacking size

Stapling size

Stack offset width*6

Offset width*5

A/B

Inch

No stapling

Staple

sorting

Not stapled

Stapled

1,000 sheets

500 sheets

30-sheet stack (30 sets max.)

20 stacks (30 sets max.)

15 stacks (30 sets max.)

Equivalent of

80 g/m2paper

Table of contents

Other Canon Printer Accessories manuals

Canon

Canon Finisher-R1 User manual

Canon

Canon AG1 User manual

Canon

Canon iPR C7010VP Series User manual

Canon

Canon BW Voice Guidance Board-A1 User manual

Canon

Canon Puncher Unit-P1 User manual

Canon

Canon FY8-13HR-000 User manual

Canon

Canon IP 1500 User manual

Canon

Canon Finisher-R1 Operating and maintenance manual

Canon

Canon Finisher-R1 Service manual

Canon

Canon PD-82 User manual

Canon

Canon INNER 2-WAY TRAY-E1 Operating and maintenance manual

Canon

Canon Super G3 3rd Line FAX Board-AE1 User manual

Canon

Canon imagePROGRAF RU-61 User manual

Canon

Canon BS1 User manual

Canon

Canon imagePROGRAF RU-42 User manual

Canon

Canon Inner Finisher-K1 User manual

Canon

Canon Finisher-T1 User manual

Canon

Canon ZDJ-S01 User manual

Canon

Canon E3730A User manual

Canon

Canon Color Network Printer Unit-D1 Reference manual

Canon

Canon CLI-521BK User manual

Canon

Canon AE-1 Reference guide

Canon

Canon Color iR Security Kit-A1P User manual

Canon

Canon Finisher-T1 User manual

Popular Printer Accessories manuals by other brands

Star Micronics

Star Micronics TSP800 Series install guide

REA

REA JET HR pro 2K user manual

HP Laserjet,Color Laserjet 4si user guide

oliser

oliser MS 45 instructions

Roland

Roland DU2-64 Supplementary manual

Xerox

Xerox EFI EXP6000 Specification sheet

Sharp

Sharp FO-1MK Service manual

Labelmate

Labelmate PM-300 user manual

Epson

Epson T6248 Product information sheet

Epson

Epson OT-BZ20 user manual

Ricoh

Ricoh LCIT RT5100 Field service manual

GBC

GBC 16 Series user guide

Develop

Develop SD-509 installation manual

Kyocera

Kyocera KM-6230 Instruction handbook

Triumph Adler

Triumph Adler DF-710 Instruction handbook

Citizen

Citizen CBM-202PC Series user manual

Codonics

Codonics Virtua 1VCX-LR833 Technical brief

TonerRefillKits

TonerRefillKits ReChargX RX126 instructions