Canon DADF-M1 Reference manual

(1/1)

Canon Service Bulletin COPIER

Issued by Canon Europa N.V.

Location:

DOCUMENT TRAY ASSEMBLY

Subject:

Frequent Appearance of Message Prompting to Clean ADF Scanning Glass

Detail:

The following message is displayed on the LCD of the host machine in order to prompt users to clean the ADF

scanning glass, although there is no dust on the glass.

Message:

Originals may not be scanned clearly (streaks may appear). Clean the thin glass strip as shown in the illustration

with a damp, well wrung-out cloth.

<Cause>

The starting position of the image scanning in the main scanning direction when using ADF (stream reading) is

determined by the position of the original. The dust detection area is determined with reference to the scanning

starting position. Also, the position of the original is determined by the position of the side guide plates of the

ADF.

If the side guide plates are fixed at a position where the edge of the original comes close to the edge of the platen

roller, the roller edge will come in the dust detection area and finally be detected as dust.

1. RCON software of the host machine is upgraded to Ver.8.01 so that the dust detection area is changed from

301mm to 298mm.

2. The procedure for adjusting the side guide plates of the DF is changed.

Service Work:

When the above symptom occurs, upgrade the Rcon Software of the host machine to Ver.8.01, referring to the

Service Information F2-T01-0M3-10016 (System Software information for iRC6800 series).

When the upgrade still fails to remove the symptom, see the attached procedure below and adjust the horizontal

registration as well.

Model:

DADF-M1

Ref No.:

DF-168

(F3-T01-00X-10014-01)

Date:

25-06-04

Horizontal Registration

(Prevention of Frequent ADF reading Glass Cleaning

Massage)

1. Adjusting the Side Guide Plate Position of

the ADF Original Pickup Tray

1) Place an original of A3 or 11x17 on the original

pickup tray. Press the Start key to run the machine.

2) Stop the machine forcibly when the original

passes through the platen roller by opening the

feeder cover.

3) Open the ADF, check the horizontal registration

(front: A/ rear: B) of the original [1] with reference

to the platen roller [2], and take a note of the

measurement.

Standard Measurement:

Original of A3: A=B=3.5mm

Original of 11x17: A=B=12.5mm

4) Open the feeder cover, and detach the inside

cover.

5) Remove the 3 mounting screws [1], and detach

the cover [2].

6) Loosen the mounting screw [1], and remove the

screw [2] from the positioning hole, and fit it and

temporarily tighten it in the adjusting angular hole

[3].

- if A > B, move the volume unit [4] to the front.

- if A < B, move the volume unit [4] to the rear.

Standard Measurement:

Original of A3: A=B=3.5mm

Original of 11x17: A=B=12.5mm

7) Tighten the screw [1] that has been tentatively

tightened and the screw [3] that has been fitted in

the adjusting angular hole.

8) When done, mount back the cover.

2. Making Adjustments Using the Host

Machine's Service Mode

1) Obtain the Test Chart.

If the Test Chart is not available, prepare one using

A4 or LTR paper as follows:

2) Place the Test Chart in the original pickup tray,

and make a copy at a 100% reproduction ratio.

3) Put the Test Chart over the output of step 2),

and check to see that the following is true

A</=1mm

B</=1mm

If not, go to step 4).

4) Start service mode as follows: press the User

Mode key, press the 2 and 8 keys at the same time,

and press the User Mode key once again.



5) Make the following selections:

COPIER>ADJUST>ADJ-XY>ADJ-Y-DF. Then,

change the setting to make adjustments.

- A higher setting will increase the margin of A,

decreasing the margin of B.

(in: 0.1 m)

(range: 21 to 106)

6) Make a copy of the Test Chart once again, and

check to see that the image is as indicated.

Other manuals for DADF-M1

Other Canon Copier manuals

Canon

Canon GP160F User manual

Canon

Canon imageCLASS 1100 User manual

Canon

Canon imageCLASS 2200 User manual

Canon

Canon C5000 - MultiPASS Color Inkjet Printer Instruction Manual

Canon

Canon iR3300 Series User manual

Canon

Canon NP-1010 User manual

Canon

Canon imageCLASS 2200 User manual

Canon

Canon CLC 5000 User manual

Canon

Canon NP6012 User manual

Canon

Canon imageRUNNER 1750i User manual

Canon

Canon iR1230 Reference manual

Canon

Canon C400D User manual

Canon

Canon image RUNNER 3045 Installation and maintenance instructions

Canon

Canon iR1210 Reference manual

Canon

Canon PC800 Series How to use

Canon

Canon iR1210 Reference manual

Canon

Canon imageRunner Advance 6275 Assembly instructions

Canon

Canon imageRUNNERC1022 User manual

Canon

Canon imageRUNNER ADVANCE Product information sheet

Canon

Canon IMAGERUNNER ADVANCE C5051 User manual

Canon

Canon imageRUNNER 1600 User manual

Canon

Canon PC6 User manual

Canon

Canon imageRUNNER 2545i User manual

Canon

Canon imageRunner 1133 User manual

Popular Copier manuals by other brands

Ricoh

Ricoh FW740 manual

Minolta

Minolta CF910 manual 

Ricoh

Ricoh B003 Service manual

Xerox

Xerox EC70 user guide

Oce

Oce 9800 user manual

Olivetti

Olivetti d-Copia 1800 Service manual

Minolta

Minolta Di181 manual 

Telecrane

Telecrane F25 manual

Xerox

Xerox WorkCentre Pro 40 user manual

Sharp

Sharp AR-5015 N Service manual

Ricoh

Ricoh Di-C1 manual

Mita

Mita MIP-2400 Instruction handbook

Sharp

Sharp AL-2061 Operation guide

Muratec

Muratec MFX-C2280 user guide

Ricoh

Ricoh FT5034C Service manual

Minolta

Minolta EP4000 Operator's manual

Ricoh

Ricoh V-C3 Technical training

Triumph Adler

Triumph Adler DCC 2526 Instruction handbook