Cabletron Systems MMAC-Plus 9G426-02 User manual

9032028

MMAC-Plus

™

Module Local Management

9G426-02

Module Specific Appendix

Appendix

9G426-02 Module Speciﬁc

Information

Introduction

This appendix contains local management information that is speciﬁc to the

9G426-02 Ethernet Module.

The 9G426-02 Ethernet Module is a 3-port switching module with:

• 2 front panel gigabit Ethernet ports

• 1 Internal Network Bus (INB) backplane port

Modifying Fields and User Privileges

To modify ﬁelds on this module, you must have read-write or super-user

privileges. If you have read-only privileges, you can view information; however,

you cannot modify any ﬁelds. For more information about user privileges and

community names, see the

MMAC-Plus Module Local Management User’s Guide.

9G426-02 Module Speciﬁc Information

Module Interface Codes

The 9G426-02 Module has 7 interfaces. Table 1 lists the identifying number, name,

and description of each interface.

Use the numbers listed in Table 1 to conﬁgure the module’s default interface (see

the General Conﬁguration Screen).

Table 1. 9G426-02 Module Interface Codes

Interface

Number

Interface

Name

Interface

Description

1 SMB1 1 Mbps System Management Bus

2 SMB10 10 Mbps System Management Bus

3 HOST i960 Host

4 LOCAL i960 Controller

5 INB Internal Network Bus

6 ENET1 Gigabit Ethernet Front Panel Port 1

7 ENET2 Gigabit Ethernet Front Panel Port 2

9G426-02 Module Speciﬁc Information

General Conﬁguration Screen

The General Conﬁguration Screen (Figure 1), displays information about the

selected module and allows you to set the following general parameters:

• Module Date and Time

• Screen Refresh and Lockout Time

• Host IP Address

• Subnet Mask

• Default Gateway and Interface

• TFTP Gateway IP Address

Figure 1. General Conﬁguration Screen

MMAC-Plus Local Management

General Configuration

Module Name: 9G426-02 Firmware Revision: 01.00.00

Slot Number: 8 BOOTPROM Revision: 01.01.01

Module Serial #: Module Date: 10/15/1996

Module Board Revision: Module Time: 10:18:31

Screen Refresh Time: 03 sec

Screen Lockout Time: 15 min

FLASH Memory: 4 MB

Host IP Address: XXX.XXX.XXX.XXX

Subnet Mask: 255.255.0.0

Default Gateway: NONE DEFINED

Default Interface: NONE DEFINED

Base MAC Address: 00-00-1D-00-00-00

TFTP Gateway IP: 0.0.0.0

SAVE EXIT RETURN

9G426-02 Module Speciﬁc Information

General Conﬁguration Screen Fields

The following information brieﬂy explains each General Conﬁguration Screen

ﬁeld.

Module Serial #

Displays the serial number of the selected module.

Module Board Revision

Displays the version number of the selected module.

FLASH Memory

Displays the amount (megabytes) of ﬂash memory in the selected module.

Module Date

Contains a value that the module recognizes as the current date. To enter a new

date, highlight the ﬁeld and enter the date in MM/DD/YYYY format. The month

and day portion of the date must include two digits. Therefore, enter a leading

zero for months January through September, and for dates less than 10. For

example, for June 4, 1996, enter 06/04/1996 (slashes are optional). If you do not

enter slashes to separate the month, day, and year values, the ﬁrst eight digits you

enter in this ﬁeld represent an entry (i.e., 06041996).

ModuleTime

Contains a value that the module recognizes as the current time. To enter a new

time, highlight the ﬁeld and enter the time in HH:MM:SS format. Notice that

there is no AM/PM indicator. Time should be entered based upon a 24 hour clock.

For 4:07 p.m., enter 16:07:00 (colons are optional). If you do not enter colons to

separate the hours, minutes, and seconds values, the ﬁrst six digits you enter in

this ﬁeld represent an entry (i.e., 160700). For 6:12 a.m., enter 6:12:00 or 061200.

Screen RefreshTime

Contains the rate at which the module’s screens are updated. This setting

determines how frequently (in seconds) information is updated on the screen. To

enter a new refresh rate, highlight the ﬁeld and enter a number. The

default

refresh rate is 3 seconds. The

range

is 3 - 99 seconds.

The module’s default date and time settings are indeterminate. The internal calendar and

clock begin running as soon as you install the module.

NOTE

9G426-02 Module Speciﬁc Information

Screen LockoutTime

Contains the maximum number of minutes that the Local Management

application will display a module’s screen while pending input or action from a

user. For example, if you enter 5 in this ﬁeld, users will have up to ﬁve minutes to

respond in some fashion to each of the speciﬁed module’s Local Management

screens. In our example, after ﬁve minutes of “idleness” (no input or action), the

Local Management application terminates the session on the selected module and

the Slot Selection Screen reappears. To enter a new lockout time, highlight the

ﬁeld and enter a number. The

default

lockout time is 15 minutes. The

range

is 1 -

30 minutes.

Host IP Address

Contains the Internet Protocol address currently assigned to the selected module.

Set this ﬁeld according to your network requirements. Highlight the Host IP

Address ﬁeld and enter the desired IP address using dotted decimal notation (4

decimal values between 1 and 255 separated by periods) as follows:

255.255.255.255

(255 is the maximum number that you can enter in any of the four segments.

Default = 0.0.0.0 .) This address can be used by any of the system interfaces on the

module.

Subnet Mask

Contains the subnet mask for the selected module. A subnet mask “masks out”

the network bits of the IP address by setting the bits in the mask to 1 when the

network treats the corresponding bits in the IP address as part of the network or

subnetwork address, or to 0 if the corresponding bit identiﬁes the host. The

default subnet mask uses the ﬁrst two portions of the IP address to identify the

network id, leaving the rest of the IP address to identify speciﬁc nodes. To enter a

new subnet mask, highlight the ﬁeld and enter a new value using dotted decimal

notation (4 decimal values between 1 and 255 separated by periods) as follows:

255.255.255.255

(The Subnet Mask ﬁeld defaults to the natural mask value, based on the IP

Address that you entered for the device.)

9G426-02 Module Speciﬁc Information

Port Statistics Screen

The Port Statistics Screen (Figure 2), displays information and statistics about the

module’s Ethernet ports.

Figure 2. Port Statistics Screen

MMAC-Plus Local Management

Port Statistics

Module Name: 9G426-02 Firmware Revision: 01.00.00

Slot Number: 8 BOOTPROM Revision: 01.01.01

PORT #: 1

OCTETS: 471908210 LINK STATUS: Link

PACKETS: 1047459244

TOTAL ERRORS: 0 PORT TYPE: FC MMF SC

COLLISIONS: 0

CRC/ALIGNMENT ERRORS: 0 PORT STATUS: ENABLED

UNDERSIZE PACKETS: 0

OVERSIZE PACKETS: 0 APPLICATION: BRIDGING

FRAGMENTS: 0

JABBERS: 0 OPERATION MODE: FULL DUPLEX

BROADCASTS: 0

MULTICASTS: 14929292

PORT #:[ 1] EXIT RETURN

9G426-02 Module Speciﬁc Information

Port Statistics Screen Fields

The following information brieﬂy explains each Port Statistics Screen ﬁeld.

PORT #

Indicates the current port for which statistics are displayed.

OCTETS

Displays the number of octets transmitted and received on the port.

PACKETS

Displays the number of packets transmitted and received on the port.

TOTAL ERRORS

Displays the total number of errors on the port.

COLLISIONS

Displays the total number of collisions detected on this port.

CRC/ALIGNMENT ERRORS

Displays the number of packets with bad Cyclic Redundancy Checks (CRC) that

have been received from the network. The CRC is a 4-byte ﬁeld in the data packet

that ensures that the transmitted data that is received is the same as the data that

was originally sent. Alignment errors are due to misaligned packets.

UNDERSIZE PACKETS

Displays the number of packets received whose size was less than the minimum

Ethernet frame size of 64 bytes, not including preamble.

OVERSIZE PACKETS

Displays the number of packets received whose size exceeded 1518 data bytes,

not including preamble.

FRAGMENTS

Displays the total number of packets received that were not an integral number of

octets in length or that had a bad Frame Check Sequence (FCS), and were less

than 64 octets in length (excluding framing bits but including FCS octets).

JABBERS

Displays the total number of packets received that were longer than 1518 octets

(excluding framing bits, but including Frame Check Sequence (FCS) octets), and

were not an integral number of octets in length or had a bad Frame Check

Sequence.

BROADCASTS

Displays the number of broadcasts received.

9G426-02 Module Speciﬁc Information

MULTICASTS

Displays the number of multicasts received.

LINK STATUS

Indicates whether there is a physical connection from this port to another device.

One of the following values appears:

• Link - There is a link signal present; there is a valid physical connection from

this port to another device.

• No Link - There is no link signal present; there is no valid physical connection

from this port to another device.

PORTTYPE

Displays the value GPIM-F01, which is an Ethernet Gigabit Fiber Channel 1 Gig,

MMF, SC

PORT STATUS

Indicates the administrative status of the selected port. Possible values are:

• ENABLED - The port is turned on administratively

• DISABLED - The port is turned off administratively

APPLICATION

Displays

BRIDGING

, indicating that the port is operating as a bridge with a

high-speed backbone connection.

OPERATION MODE

Displays the value

FULL DUPLEX

. The port can transmit and receive data at the

same time. Therefore, the port is running at 1000 Mbps.

PORT # (Modiﬁable)

Selects the port for which statistics are to be displayed.

Enable or disable ports from the Bridge Conﬁguration screen.

NOTE

Other manuals for MMAC-Plus 9G426-02

Table of contents

Other Cabletron Systems Switch manuals

Cabletron Systems

Cabletron Systems SEH-24 User manual

Cabletron Systems

Cabletron Systems SmartSwitch 6500 User manual

Cabletron Systems

Cabletron Systems SEH100TX-22 User manual

Cabletron Systems

Cabletron Systems MRXI-22 User manual

Cabletron Systems

Cabletron Systems DLEHF-MA User manual

Cabletron Systems

Cabletron Systems SmartSwitch 6500 User manual

Cabletron Systems

Cabletron Systems 6A000/ZX-250 User manual

Cabletron Systems

Cabletron Systems SmartSTACK EPIM1000-S1LX 1000BASE-LX User manual

Cabletron Systems

Cabletron Systems SmartSwitch 8000 User manual

Cabletron Systems

Cabletron Systems MMAC-Plus 9F116-01 User manual

Cabletron Systems

Cabletron Systems SmartSwitch 9000 User manual

Cabletron Systems

Cabletron Systems 9A426-01 Technical document

Cabletron Systems

Cabletron Systems FN10 User manual

Cabletron Systems

Cabletron Systems Cabletron CyberSWITCH CSX5500 Instruction Manual

Cabletron Systems

Cabletron Systems HubSTACK SEHI-34 User manual

Cabletron Systems

Cabletron Systems FRM User manual

Cabletron Systems

Cabletron Systems MMAC-Plus 9E312-12 User manual

Cabletron Systems

Cabletron Systems MMAC-Plus 9T122-24 User manual

Cabletron Systems

Cabletron Systems MMAC-Plus 9T125-08 User manual

Cabletron Systems

Cabletron Systems SmartSTACK ELS100-8TXUF2 User manual

Cabletron Systems

Cabletron Systems STHI User manual

Cabletron Systems

Cabletron Systems SmartSwitch 9000 User manual

Cabletron Systems

Cabletron Systems bridges User manual

Cabletron Systems

Cabletron Systems SmartCell 6A000 User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual