Cabletron Systems SmartSWITCH 7H02-06 User manual

7H02-06 Fast Ethernet

SmartSWITCH

™

Interface

Module User’s Guide

9031924

Notice

NOTICE

Cabletron Systems reserves the right to make changes in

speciﬁcations and other information contained in this document

without prior notice. The reader should in all cases consult

Cabletron Systems to determine whether any such changes have

been made.

The hardware, ﬁrmware, or software described in this manual is

subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR

ANY INCIDENTAL, INDIRECT, SPECIAL, OR

CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING

BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR

RELATED TO THIS MANUAL OR THE INFORMATION

CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN

ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE

POSSIBILITY OF SUCH DAMAGES.

Cabletron Systems, Inc.,

35 Industrial Way

Rochester, NH 03867-0505

Printed in the United States of America

Order Number: 9031924 July 22, 1996

LANVIEW

is a registered trademark of Cabletron Systems, Inc.

Ethernet

is a trademark of Xerox Corp.

CompuServe

is a registered trademark of CompuServe, Inc.

Notice

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

NOTE:

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15 of the

FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is

operated in a commercial environment. This equipment uses,

generates, and can radiate radio frequency energy and if not

installed in accordance with the operator’s manual, may cause

harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause interference in

which case the user will be required to correct the interference at his

own expense.

WARNING:

Changes or modiﬁcations made to this device which

are not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

DOC NOTICE

This digital apparatus does not exceed the Class A limits for radio

noise emissions from digital apparatus set out in the Radio

Interference Regulations of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits

radioélectriques dépassant les limites applicables aux appareils

numériques de la class A prescrites dans le Règlement sur le

Notice

iii

brouillage radioélectrique édicté par le ministère des

Communications du Canada.

VCCI NOTICE

This equipment is in the 1st Class Category (information

equipment to be used in commercial and/or industrial areas) and

conforms to the standards set by the Voluntary Control Council for

Interference by Information Technology Equipment (VCCI) aimed

at preventing radio interference in commercial and/or industrial

areas.

Consequently, when used in a residential area or in an adjacent area

thereto, radio interference may be caused to radios and TV

receivers, etc.

Read the instructions for correct handling.

Notice

EXCLUSION OFWARRANTY

AND DISCLAIMER OF LIABILITY

1. EXCLUSION OF WARRANTY. Except as may be speciﬁcally

provided by Cabletron in writing, Cabletron makes no warranty,

expressed or implied, concerning the Program (including Its

documentation and media).

CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN

THOSE SUPPLIED TO YOU BY CABLETRON IN WRITING,

EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT

LIMITED TO IMPLIED WARRANTIES OF MERCHANTABLITY

AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT

TO THE PROGRAM, THE ACCOMPANYING WRITTEN

MATERIALS, AND ANY ACCOMPANYING HARDWARE.

2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO

EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIABLE

FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT

LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,

BUSINESS INTERRUPTION, LOSS OF BUSINESS

INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL,

OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF

THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT,

EVEN IF CABLETRON HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES

DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL

DAMAGES, OR ON THE DURATION OR LIMITATION OF

IMPLIED WARRANTEES IN SOME INSTANCES THE ABOVE

LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.

CONTENTS

CHAPTER 1 INTRODUCTION

1.1 USING THIS MANUAL .........................................................................1-1

1.2 THE 7H02-06 MODULE..........................................................................1-2

1.2.1 Cable Type and FEPIMs................................................................1-2

1.2.2 7C03 MMAC SmartSWITCH, the 7C04 Workgroup

SmartSWITCH and the 7C04-R Workgroup SmartSWITCH...1-3

1.3 FEATURES ................................................................................................1-4

1.3.1 LANVIEW LEDs............................................................................1-4

1.3.2 FEPIMs ............................................................................................1-5

1.3.3 Connectivity....................................................................................1-5

1.4 RELATED MANUALS ............................................................................1-6

1.5 GETTING HELP.......................................................................................1-6

CHAPTER 2 NETWORK REQUIREMENTS

2.1 FEPIM Module Speciﬁcations ................................................................2-1

2.2 FE-100FX....................................................................................................2-1

2.3 FE-100TX and Fixed RJ45 Ports..............................................................2-2

CHAPTER 3 INSTALLATION

3.1 UNPACKING THE 7H02-06 MODULE................................................3-1

3.2 INSTALLING FEPIMS.............................................................................3-1

3.3 INSTALLING/REMOVING THE 7H02-06 MODULE.......................3-3

3.3.1 Installing the 7H02-06 Module in a 7C03 MMAC

SmartSwitch....................................................................................3-3

3.3.2 Removing the 7H02-06 Module from a 7C03 MMAC

SmartSwitch....................................................................................3-5

3.3.3 Installing the 7H02-06 Module in a 7C04

or 7C04-R Chassis ..........................................................................3-6

3.3.4 Removing the 7H02-06 Module from a 7C04

or 7C04-R Chassis ..........................................................................3-8

CHAPTER 4 TROUBLESHOOTING

CHAPTER 5 TECHNICAL SPECIFICATIONS

5.1 SYSTEM RESOURCES ............................................................................5-1

5.2 STANDARDS............................................................................................5-1

Contents

5.3 SAFETY......................................................................................................5-1

5.4 EMI .............................................................................................................5-1

5.5 IMMUNITY...............................................................................................5-2

5.6 NETWORK INTERFACES ......................................................................5-2

5.7 SERVICE ....................................................................................................5-2

5.8 PHYSICAL ................................................................................................5-2

5.8.1 Dimensions .....................................................................................5-2

5.8.2 Weight..............................................................................................5-2

5.8.3 Environmental................................................................................5-3

APPENDIX A

A.1 FE-100TX ................................................................................................ A-1

A.2 FE-100FX................................................................................................. A-1

1-1

CHAPTER 1

INTRODUCTION

Welcome to Cabletron Systems 7H02-06 Fast Ethernet

SmartSwitch

™

Interface Module Installation Guide. This guide is a

simple reference for installing and using the 7H02-06 Module.

Before installing the module, carefully read this manual to gain a

full understanding of its capabilities.

The 7H02-06 Module is a six port Fast Ethernet module that

supports 10/100 operation in both half and full duplex. The 7H02-

06 Module supports auto negotiation allowing it to automatically

use the fastest link both it and the attached device are capable of.

Connectivity to the ports is provided by 5 RJ45 connectors and one

Fast Ethernet Port Interface Module (FEPIM), allowing either

Category 5 twisted pair or multimode ﬁber optic cabling. This

module connects to a network and the 7X00 SmartSwitch Control

Module in the 7C03, 7C04 or 7C04-R MMAC SmartSwitch via a

SmartSwitch bus.

1.1 USINGTHIS MANUAL

Chapter 1,

Introduction

, discusses the capabilities and special

features of Cabletron Systems 7H02-06 Module. This chapter also

includes a list of related manuals.

Chapter 2,

Network Requirements

, contains a list of available

FEPIMs and the network requirements that should be considered

before installing the 7H02-06 Module.

Chapter 3,

Installation

, contains instructions for installing the

7H02-06 in the 7C03 MMAC SmartSwitch, the 7C04 Workgroup

SmartSwitch or the 7C04-R Workgroup SmartSwitch.

Chapter 4,

Troubleshooting

, contains instructions for using

LANVIEW

(Cabletron Systems built-in diagnostic and status

monitoring system).

Chapter 5,

Technical

Speciﬁcations,

provides detailed information

about the physical characteristics of the 7H02-06 Module.

1-2

Introduction

1.2 THE 7H02-06 MODULE

The 7H02-06 Module provides six Fast Ethernet ports via 5 RJ45

connectors and one FEPIM. The 7H02-06 Module can be installed

in:

• The 7C03 MMAC SmartSwitch

• The 7C04 Workgroup SmartSwitch Chassis

• The 7C04-R Workgroup SmartSwitch Redundant Chassis

The 7H02-06 Module has one backplane connection and six front

panel connections. The backplane connection provides power to

the 7H02-06 Module and a channel for communication with the

7X00 SmartSwitch Control Module. The six front panel ports

provide Category 5 Twisted Pair (UTP) and one user conﬁgurable

port for UTP or multimode ﬁber optic connectivity (through the

FEPIM).

1.2.1 CableType and FEPIMs

The 7H02-06 module has six front panel connectors that interface to

the 7X00 SmartSwitch through the chassis backplane. 100 Base-TX

connections are provided through 5 RJ45s; one FEPIM provides 100

Base-TX (via RJ45) or 100 Base-FX (via multimode SC).

Note:

UTP operates at 10/100 Mbps, while Fiber operates at 100 Mbps.

Both UTP and Fiber are capable of half or full duplex operation.

Table of contents

Other Cabletron Systems Network Router manuals

Cabletron Systems

Cabletron Systems SMARTSWITCH ROUTER 9032578-05 Assembly instructions

Cabletron Systems

Cabletron Systems NB20E User manual

Cabletron Systems

Cabletron Systems CSX200 CyberSWITCH User manual

Cabletron Systems

Cabletron Systems MMAC-Plus 9F106-02 User manual

Cabletron Systems

Cabletron Systems ESX-1380 Programming manual

Cabletron Systems

Cabletron Systems SmartSwitch 2200 Operation manual

Cabletron Systems

Cabletron Systems MMAC-Plus 9T106-01 User manual

Cabletron Systems

Cabletron Systems DELST-UI Programming manual

Cabletron Systems

Cabletron Systems SSR 2000 User manual

Cabletron Systems

Cabletron Systems MMAC-Plus 9F106-01 User manual

Cabletron Systems

Cabletron Systems Cabletron SmartSwitch Router 250 User manual

Cabletron Systems

Cabletron Systems Spectrum EMM-E6 User manual

Cabletron Systems

Cabletron Systems CyberSWITCH CSX400 User manual

Cabletron Systems

Cabletron Systems 2000 User manual

Cabletron Systems

Cabletron Systems SmartSTACK ELS100-24TXG User manual

Cabletron Systems

Cabletron Systems ESX-1380 Installation and operating instructions

Cabletron Systems

Cabletron Systems CyberSWITCH CSX400 User manual

Cabletron Systems

Cabletron Systems SmartSTACK ELS100-24TXM User manual

Cabletron Systems

Cabletron Systems BRIM-WT1 User manual

Cabletron Systems

Cabletron Systems MMAC-Plus 9W111-08 User manual

Cabletron Systems

Cabletron Systems SmartSwitch Router User manual

Cabletron Systems

Cabletron Systems Network Router User manual

Cabletron Systems

Cabletron Systems BRIM E100 BRIM-E100 User manual

Cabletron Systems

Cabletron Systems CyberSWITCH CSX400 User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview