BUNGY CDH1R-E User manual
OWNER’S MANUAL
AUTOMATED CEILING MOUNTED DRYING RACK
BUNGY
MODEL CDH1R-E
Thank you for purchasing a BUNGY drying rack.
Now the ease of drying clothes in a convenient
and environmentally friendly way is at the dis-
tance of a simple assembly.
Before starting the installation of your drying
rack please read this entire manual.
If you have difficulties please contact one of our
installers who can do the assembly for you.
bungy.pt
facebook.com/bungy.pt
Patented system
Made in Portugal
Package contents
Tools you will need
On the roof, indoors, in a sheltered area, need-
ing only a power point with live, neutral and
earth.
Where to mount your BUNGY?
x4 x4 x4 x4x1 x1
Set up
Cardboard matrix for marking the holes in the ceiling
RackMotorized ceiling structure
Remote
control
Drilling
Using the cardboard matrix mark the 4 fixing holes,
leaving the required space for the rack not to touch
the wall.
Drill 4 holes with 8mm in diameter in the ceiling and
put the wall plugs
1. 2.
Free area of 130cm x 80cm. Should be taken
into account the existence of any obstacle to
the ascent and descent of the drying rack.
If you have a droppes ceiling the installation
should always be performed by a professional.
WARNING: Improper installation of this equip-
ment can cause it to malfunction or put people
at risk - If you are unsure you can perform a
correct and safe installation, please contact a
professional. Go to BUNGY.pt.
Power drill
Drill bit 6mm and 8mm
Wrench
8mm
Phillips
P2 Screwdriver
Hammer
Bracket
Remove the motor cover Secure the structure and
motor to the ceiling
Assemble the motor cover
Fit the drying rack
Wiring BUNGY
Screw the remote control
to the wall
Unscrew the motor cover. Place the metal structure with the motor by aligning
its holes with the holes in the ceiling.
Place and tighten the screws in the order shown in
the image.
Place the motor cover and tighten the two screws.
Connect BUNGY to power respecting the color code:
Blue - neutral; Brown - live; Green and yellow - Earth
Secure the remote control wall bracket in an
appropriate location with the supplied screw.
Fix the hanger to the strips with the supplied screws
and nuts.
3.
6.
5.
4.
7. 8.
WARNING: The gray and black conductors
should not be used, must be isolated and
can not be connected to electricity.
12
3
4
Cancellation the lower and higher limit switched
- Press the "P" key three times.
- Immediately after press the key to cancel the upper
limit switch or the key to cancel the lower limit switch.
- The system will confirm the cancellation with a brief
movement of ascent and descent.
- Press to exit the cancellation menu.
- Reprogram the annulled limit switch, bearing in mind
that the upper limit switch must leave a minimum safety
distance from the engine cover and the lower limit switch
must leave at least two rounds of the suspension strips
coiled on the engine.
This operation must be made in advance by removing
the motor cover to allow the necessary visibility.
Your BUNGY is pre-programmed with upper and lower
limit switches.
When necessary these setting can be changed using the
remote control. The programming key "P" can be
accessed through a hole in the rear face of the remote
control
Upper limit switch programming
- Use the arrow keys to move the drying rack to the
desired height, leaving a minimum distance off the engine
cover
- Press the "P" key once
- Immediately after press the key
- The system will confirm the changes with a brief move-
ment of ascent and descent
Lower limit switch programming
- Use the arrow keys to move the drying rack to the
desired height
- Press the "P" key once
- Immediately after press the key
- The system will confirm the changes with a brief move-
ment of ascent and descent
Preprograming an intermediate height:
- Use the arrow keys to move the hanger to the desired
height
- Press the button four times in a row
- The system will confirm the change with a brief move-
ment of ascent and descent
Raises the rack to the highest position close
to the ceiling
Stops any movement upward or downward
By pressing it for 4 seconds it takes the tack
to a preset intermediate height.
Lowers the rack to its lowest position
Using the remote control
9.
Reprogramming of the
limit switches
10.
Model CDH1R - E
Color White
Motor voltage 220 ~ 240VAC 50Hz
Remote control batteries 3VDC type CR2032
Drying rack size 1,20m x 0,70m
Clothesline linear length 8,40m
Required area for instalation 1,30m x 0,80m mínimo
Maximum height from ceiling 1,60m (lower position)
Maximum supported weight 20Kg
BUNGY ensures that this equipment will remain free
from manufacturing defects for two years effective
from the date of original purchase, confirmed by proof
of purchase.
This warranty does not cover:
a. Travel and maintenance interventions
b. Transport and travel for repair at home
c. Any damage, loss, cost or expense, direct, indirect,
incidental, consequential or special, arising out of or
related to the product.
d. Damage resulting from:
• Incorrect installation
• Improper Use
• Changes to equipment
• Other causes beyond the control of BUNGY
This warranty does not affect your statutory consumer
rights, consecrated in national laws, resulting from the
respective sale / purchase contract.
Technical specifications
Warranty
Replacing the remote control battery:
The remote control has a battery with limited life and it
status can be checked by the intensity of the light when
you press a key.
To replace the battery, open with the help of a screw-
driver, the cover on one of the sides of the remote
control and replace the battery with a new CR2032
battery.
You will not need to do any reprogramming.
v. CDH1R -E01
Other BUNGY Rack & Stand manuals
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
