Bullet RPZ1600 User manual
1600W SCOOTER
OWNER’S MANUAL
TABLE OF CONTENTS
TABLE OF CONTENTS……………………………………………………………2
IMPORTANT INFORMATION…………………………………………………..3-4
QUICK REFERENCE………………………………………………………………5
GETTING TO KNOW YOUR SCOOTER………………………………………….6
PACKAGE CONTENTS…………………………………………………………….7
GETTING STARTED………………………………………………………………..7
ASSEMBLY…………………………………………………………………….7-8
FUSE INSTALLATION…………………………………………………………..8
SEAT&SEAT POST INSTALLATION……………………………………………8
CHARGING……………………………………………………………………….9
RIDING/BRAKING……………………………………………………………….9
FOLDING AND STORAGE…………………………………………………………10
BRAKING SYSTEM………………………………………………………………...10
ADJUSTING BRAKES……………………………………………………………...10
TIRE PRESSURE……………………………………………………………………11
MAINTENACE……………………………………………………………………...12
RECOMMENDED TOOLS.....................................................................................12
ADJUSTING THE HEAD UNIT............................................................................12
ADJUSTING THE CHAIN……………………………………………………12-13
MAINTENANCE SCHEDULE……………………………………………………...13
TROUBLESHOOTING GUIDE……………………………………………………..14
OTHER QUESTIONS………………………………………………………………14
CIRCUIT DIAGRAM………………………………………………………………..15
TECHNICAL PARAMETER………………………………………………………...16
PLEASE BE SAFE WHEN RIDING
ALWAYS WEAR A HELMET AND OBEY ALL LAWS!
BATTERY MAINTENANCE and CHARGING
INSTRUCTIONS
1. You MUST charge completely prior to initial use. (Follow charging
instructions in your Product Handbook)
2. Charge immediately after each use.
3. Charge before storage. You must charge every 30 days if not in use.
4. Charge the unit for 6-8 hours or until the light on the charger turns
red& green.
5. DO NOT allows this unit to deep discharge the battery.
6. For safety purposes, DO NOT charge for over 24 hours.
7. Turn the unit OFF when not in use.
8. In the use of electric skateboards car should check handlebar, saddles,
saddle tube and wheel fastener whether tighten, folding institutions
locking structure whether lock, should pay attention to the safety of
saddle tube; Should check whether the brake effectively
Failure to follow these INSTRUCTIONS will
VOID YOUR WARRANTY!
IMPORTANT
This PRODUCT IS NOT INTENDED FOR EXTREME OFF-ROAD Use!
Please take care of your Bullet 1000w!
DO NOT JUMP orABUSE THISPRODUCT!
DO NOT RIDE IN WET/ICY CONDITIONS!
Failure to follow these instructions will
VOID YOUR WARRANTY!
WARNING
This product does not conform to Federal Motor Vehicle Standards and is not
intended for operation on public streets, roads or highways. Serious injury can result
from the unsafe operations of this product. Operator can minimize these risks by
using certain safety equipment such as: safety helmet, goggles, gloves, elbow and
kneepads and appropriate footwear.
DO NOT operate in traffic, on wet, frozen, oily or unpaved surfaces or under the
influence of drugs and/or alcohol. Avoid uneven surfaces, potholes, surface cracks
and obstacles.
DO NOT use a water hose to clean this product. See Product Handbook for more
information.
This product is recommended for riders 13 YEARS OF AGE and older.
SAFETY
Persons without excellent vision, balance, coordination, reflex, muscle and bone
strength and good decision-making capabilities should not use this product.
Minors without adult supervision should not use this product.
Persons unwilling or unable to take responsibility for their own actions should
not use this product.
The user of this product assumes ALL risks associated with its associated with its
use. To minimize these RISKS, the user must wear safety helmet, goggles, gloves,
elbow and kneepads and appropriate footwear.
This product is ELECTRIC! DO NOT ride this product in wet conditions, puddles or
rainy weather.
IMPORTANT
PLEASE AND THIS BEFORE USING THIS PRODUCT
READ THIS FIRST!
SAFETY GUIDE
The recommended minimum age for riding this scooter is 13 years old.
To avoid damage to the motor and footplate, do not overload the scooter.
Never ride with more than one person.
Inspect your scooter thoroughly before each use for loose or missing parts.
Avoid unintentional starts by turning the scooter off while not in use.
To avoid the risk of a short circuit in the electrical parts, do not use your Electric
scooter in the rain and never spray or wash off your scooter with water.
Do not place the battery near fire or heat.
To avoid damage to the battery, do not use the charger if it has been damaged in any
way.
Keep hands, face, feet and hair away from all moving parts.
Do not touch the motor or wheels while they are rotating.
Brakes are designed to control speed as well as stop the scooter. Practice braking for
proper slowing down and smooth stops.
Maintain your SCOOTER as recommended in this Product Handbook.
Use only quality replacement parts as recommended by the manufacturer.
Inspect the entire scooter prior to each use. Replace any part that is cracked, chipped
or damaged before use.
*NEVER ALLOW CHILDREN TO OPERATE THE SCOOTER WITHOUT ADULT
SUPERVISION.
*NEVER ATTEMPT TO OPERATE THE SCOOTER WHILE UNDER THE INFLUENCE OF
ALCOHOL.
If a situation arises that is not covered in the manual,
Proceed with caution and use good judgment.
Contact your dealer
If you need further assistance
QUICK REFERENCE
SAFETY GUIDE
GETTING TO KNOW YOUR SCOOTER
(Photo’s may vary)
Optional Seat
Kit Included
Powerful 800
Wait Motor
Front & Rear
Hand Brakes
Variable speed
throttle
Front Shocks
Front Disc Brakes
10”Aluminum Wheels
Lock and Fold
Design for easy Storage
Rear Brakes
Rear Shock
PACKAGE CONTENTS
Your Scooter comes with following items in the box. Please locate all of the following:
1. Scooter
2. 36V Battery Charger
3. Tool Kit User Manual and 25 amp Fuses
4. Seat
5. Seat Post & Clamp
Getting started
Please read and understand these instructions and the OPERATING PRO
CEDURES section, prior to starting or riding your BULLET 1600W
Assembly
1.
Carefully remove the scooter
form the box. Then install the
wheels please.
2. To unfold the scooter,
begin by pressing down on
the FOLDING HSNDLE
with one hand while gently
3. Fully extend the handlebars
to their upright position until
you feel the mechanism lock
into place
4. Attach the handlebars by inserting the
silver handlebar clamp onto the handlebar
post stopping just below the top. Be sure
to orient the bars in the correct riding
position with the throttle on the rider’s
right side. Secure the handlebars to the
post by tightening the bolts on the clamp
with the enclosed Allen wrench as shown.
Assembly-Continued:
5. Secure the hand brakes in place by
using the provided Allen Wrench to first
loosen the tension bolts.
Adjust the
levers to a comf
ortable position and
tighten the bolts.*BE CAREFUL NOT
TO PULL ON THE CABLES！
6. Insert the 25 amp fuse by
opening the footplate cover as
shown. Insert the fuse into the
fuse hol
der then close the
footplate cover.
7. Attach the seat post to the seat
post receiver, and then attach the
clamp to the top of the seat post.
P
ull the upper seat post to the
desired position and tighten the
clamp securely.
8. Attach the seat to the upper
seat post and tighten the seat
bolts as shown.
CHARGING
Your scooter comes charged out of the carton. We still recommend charging the unit
for 6-8 hours prior to its first use. We also recommend charging your scooter after
each use and prior to storage.
Warning: Do not allow scooter to go into deep discharge, as this will damage the
batteries.
RIDING
1. Make sure that all of the exposed bolts and screws are tightened.
2. Raise the kickstand to its upright position.
3. Push the on/off switch (located on the handlebar) to the ON position.
1. Make sure unit is turned off.
2. Open the charging socket
cover located on the right
side of the scooter frame,
under the footplate.
3. Locate your Battery Charger.
Find the charger socket and plug it into the
scooter.
4. Next, plug theAC into a wall outlet
When first plugged in the charger has one red light
that will illuminate at the same time, indicating that
the charging process has started. Once the light on the
charger turns red &green, you may remove the
charger and close the safety cap.
Table of contents
Other Bullet Scooter manuals
