BREWISTA NutraMilk Operating and maintenance instructions
Making Alternative Butter
Assemble the NutraMilk
Assemble the NutraMilk (Continued)
QUICK
START
GUIDE
1
1
3
2
2
• Set the base on a flat
surface with arm tilted
up from the base.
• Place the mixing basin
on the center of the
base with spigot hole
towards the front (1).
• Twist basin to lock in
place (2).
• Insert neck of the
dispensing spigot into
hole at front of the
mixing basin until it
clicks into place (3).
• Rotate the lid counter-
clockwise to unlock
and remove.
• Insert the inner lter
within the mixing
basin and center it into
position.
• Add ingredients.
• Refer to User Manual
or Recipe Book for
recommended ingredient
measurements.
• Press the BUTTER button, then the START/STOP
button to start the butter cycle.
• Refer to User Manual or Recipe Book for
recommended processing times for various
ingredients.
What’s in the Box?
Lid
Mixing Basin
Motor Base
Wiper Blades
Cutting Blade
Dispensing
Spigot
Inner Filter
Recipe Book
Scan for Video
Cleaning Brush
• Carefully align cutting blade with center post of base
and press rmly to install.
WARNING: LACERATION HAZARD - Handle
blade carefully; it is very sharp. Make sure
unit is unplugged before installing or
removing blade.
• Place wiper blades into inner lter.
• Replace lid and twist
clockwise to lock into
place.
• Lower arm to lock into
top of lid.
• Plug the power cord
into a grounded wall
outlet. Refer to User
Manual for grounding
instructions.
• Press the power
switch at the back of
the appliance. The
LCD readout will
display “00”.
1133 W. 27th Street, Cheyenne, WY 82001, USA | www.thenutramilk.com
Toll Free in North America: 888-538-8683 | Local: 307-222-6086
• Press the MIX button, then the START/STOP
button to start making alternative milk.
• When the alternative milk
is ready to drink, press the
DISPENSE button, then
the START/STOP button to
dispense the milk. Open
spigot to dispense into
another container.
• Refrigerate alternative
milk for up to
5-6 days.
• Butter your ingredients
following the instructions
above.
• Add up to 2L of water
once butter process is
complete.
• Clean the outside of the base and the
attached arm with a damp, soft cloth.
• Disassemble and clean the basins,
blades, and wiper blades with dish
detergent and rinse thoroughly with
water OR wash in a dishwasher (top
rack recommended).
• Use the enclosed cleaning brush to
clean the steel mesh on the inner lter.
• Do not use abrasive cleaners.
• After cleaning, dry all components
thoroughly prior to storage.
WARNING: Never immerse the
base in water or other liquids.
WARNING: Always unplug the
appliance prior to cleaning.
Making Alternative Milk
Cleaning the NutraMilk Troubleshooting
3
4 5
BRNMC2L Series
Note: Only
use cool water
when making
alternative milk.
Do not use hot
water in your
NutraMilk or you
may damage your
machine!
Components to check:
- Ensure the mixing basin is securely locked
into place.
- Ensure the lid is fully locked by turning
it counter-clockwise to open and then
clockwise to close and lock.
- With lid locked, ensure that the arm is
locked into the lid securely. If the wiper
drive gear does not line up when lowering
the arm into place, rotate the wiper blades
a quarter turn by hand and lower arm
again.
• Refer to the User Manual for additional
troubleshooting tips.
• If the LCD displays “Er” when
any function button is pressed,
the components have not been
assembled correctly. Unplug
the unit and re-assemble its
components.
Other BREWISTA Brewing System manuals
