BRC INOXTRAP IP 65 User manual
INSTRUCTION SHEET
INOXTRAP IP 65
Indice A
29/11/13
INOXTRAP IP65 –INSTRUCTION SHEET
THE RANGE
The stainless steel series INOXTRAP insect
killer are the best solution for the
destruction and control of flying insects.
The neutralization of insects is by trapping
on glueboards. INOXTRAP can be suspended
from the ceiling or wall mounted.
WARNING
INOXTRAP MUST ONLY BE USED IN AREAS WHICH
ARE FREE OF DUST AND POSSIBLE EXPLOSIVE
VAPOUR MIXTURE. SHOULD YOU HAVE ANY
QUERIES CONTACT YOUR LOCAL FIRE
AUTHORITY FOR ADVICE BEFORE INS-
TALLATION.
INOXTRAP IS ONLY SUITABLE FOR INDOOR USE
AND IS NOT SUITABLE FOR USE IN BARNS,
STABLES and SIMILAR LOCATIONS.
INSTALLATION
INOXTRAP unit requires certain conditions
to ensure the effective control of flying
insects in your premises:
1–It must be correctly sited
2–It must be the correct model for the
area to be protected
3- It must be in operation for 24 hours a
day.
POWER REQUIREMENTS
INOXTRAP units are designed to operate
from the following power supply : 220V /
50Hz
Therefore, please ensure that your unit is
compatible with the electricity supply in
your premises.
DANGER : this product is subjected to a
high voltage
IMPORTANT
This fly killer is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience of knowledge, unless they
have been given by a person responsible for
their safety, monitoring or instruction
concerning use of the appliance (A2/EN
68335-1). It should supervise children to
ensure they don’t play with the fly killer.
POSITIONING
INOXTRAP unit should ideally be fixed at
least two meters above the ground, pre-
ferably in the darkest place within the area
to be protected, away from windows and
skylights, thus avoiding any competition
with natural daylight or sunlight.
In large open areas where two or more
units are required, siting needs careful
consideration to ensure maximum
protection. Each unit within a certain area
should be centrally positioned.
The wall mounting is carried out by means
of suitable equipments (bolts, screws,
etc…) to the weight of the unit. The
suspension makes edding using chains (not
includes).
SERVICING
BEFORE ANY FORM OF SERVICING, ENSURE THAT
THE UNIT IS DISCONNECTED FROM THE MAINS
SUPPLY.
To maintain the units efficiency, replace
the UV fluorescent bulbs every 12 months,
glueboards must be replaced every two
months.
IF ANY DOUBTS ARISE REGARDING THESE
INSTRUCTIONS, PLEASE CONTACT YOUR SUPPLIER.
GUARANTEE
INOXTRAP is guaranteed for 5 years (exclu-
ding replacement bulbs and glueboards). If
a fault occurs, contact your supplier, who
will replace your unit providing the product
has been operated under normal
conditions.
Model
Power supply
UV light
Protection area
INOXTRAP 218
230V –50 Hz
2 x 18 W
120 m²
INOXTRAP 236
230V –50 Hz
2 x 36 W
240 m²
Other BRC Heater manuals
Popular Heater manuals by other brands
oventrop
oventrop Regucor Series quick start guide
Blaze King
Blaze King CLARITY CL2118.IPI.1 Operation & installation manual
ELMEKO
ELMEKO ML 150 Installation and operating manual
BN Thermic
BN Thermic 830T instructions
KING
KING K Series Installation, operation & maintenance instructions
Empire Comfort Systems
Empire Comfort Systems RH-50-5 Installation instructions and owner's manual
Empire Heating Systems
Empire Heating Systems WCC65 Installation and owner's instructions
Wetekom
Wetekom 92 86 43 Original instructions
Desa
Desa SPC170-F owner's manual
Watlow
Watlow Watrod Electric Tubular Heaters Specifications
Haverland
Haverland ECO-DRY GPS Series Instruction & installation manual
Stelpro
Stelpro ASILVC2060 Series user guide