Bravo EVT-4000e User manual
1
EVT-4000e
Maintenance Manual
EVT TECHNOLOGY CO., LTD.
2
(1) HEAD LIGHT ASSY
Replace Head Light Assy :
(1) Release three screws on the handle cover
(Picture 1)
(2) Release two mounting screws on the instrument panel, and then release three screws
on the head light assy (Picture 2)
(3) Follow with the reversed steps to restore
Tools!"(1) (2) screwdriver
(Picture 1)
Three screws on
the handle cover
Two mounting screws
on the instrument
Three screws on
the head light assy
Signal light bulb set
3
(Picture 2)
Replace Head Light Bulb"
(1) Release three screws on the handle cover
(Picture 1)
(2) Release two mounting screws on the instrument panel so can easily replace the
bulb (Picture 2)
(3) Follow with the reversed steps to restore
Tools! " (1) (2) screwdriver
Replace Signal Light Bulb"
(1) Release three screws on the handle cover
(Picture 1)
(2) Release signal light bulb set for replacement
(Picture 2)
(3) Follow with the reversed steps to restore
Tools! " (1) screwdriver
4
(2) SPEEDOMETER ASSY
Replace Instrument Panel :
(1) Release three screws on the handle cover (Picture 1)
(2) Release two mountingscrews on the instrument panel (Picture 2)
(3) Release the nut for the speedometer (Picture 3)
(4) Follow with the reversed steps to restore
Tools＞：(1) (2) screwdriver
(Picture1)
(Picture2)
Three screws on
the handle cover
Twomounting
screws on the
instrument panel
5
(Picture3)
Replace SpeedometerCable:
(1) Release three screws on the handle cover
(Picture 1)
(2) Release two mountingscrews on the instrument panel
(Picture 2)
(3) Release the nut for the speedometer
(Picture 3)
(4) Release three screws on the front cover
(Picture 4)
(5) Release speedometer nut on the front wheel
(Picture 5)
(6) Follow with the reversed steps to restore
Tools＞：(1) (2) (4) screwdriver
Speedometer bolt
Speedometer nut
Speedometer cable
6
(Picture4)
(Picture5)
Replace SpeedometerGear:
(1) Release front axle nut
(Picture 5)
(2) Remove the front wheel
(3) Follow with the reversed steps to restore
Tools＞：(1) box wrench（17mm）
Three screws on the front cover
Speedometer nut
Front axle nut
Speedometer gear
7
(3) KEYSWITCH AND HORN
Replace Key Switch :
(1) Release three screws on the front cover
(Picture 1)
(2) Release sixscrews on the front fender
(Picture 1)
(3) Release three screws on the glove box
(Picture 2)
(4) Release 4 pin connector and two screws on the keyswitch
(Picture 3)
(5) Follow with the reversed steps to restore
Tools＞：(1) (2) screwdriver；(3) T-bend socket wrench（8mm）& screwdriver；
(4) T-bend socket wrench（10mm）
(Picture1)
Three screws on the
front cover
Six screws on the
front fender
8
(Picture2)
(Picture3)
Three screws on
the glove box
Two screwsfor the key
switch on left and right side
4 pin connector
9
Replace Horn:
(1) Release three screws on the front cover
(Picture 1)
(2) Release two connectors on the horn
(Picture 2)
(3) Release the mounting screws on the horn
(Picture 4)
(4) Follow with the reversed steps to restore
Tools＞：(1) screwdriver；(3) open-end wrench（10mm）
(Picture4)
Two connectors on
the horn
Two mounting screws
on the horn
10
(4) MAIN CONTROLCORD
Replace Main Control Cord :
(1) Release three screws on the handle cover, two mountingscrews on the instrument panel,
three screws on the head light, three screws on the front cover and two screws on the right
trim
(Picture 1 & 2)
(2) Release all of the connectors stored inside the handle cover
(Picture 3)
(3) Release all of the connectors stored inside the front cover
(Picture 4)
(4) Release all of the connectors stored inside the right cover
(Picture 5)
(5) Follow with the reversed steps to restore
Tools＞：(1) screwdriver
(Picture1)
Three screws on
the handle cover
Three screws on the
front cover
Table of contents
Other Bravo Scooter manuals
