BrandMotion 9002-8808 User manual
INSTALLATION(INSTRUCTIONS(
9002-8808.docx Page 1 of 6 JM
Jeep Wrangler Rear Vision Camera for Smittybilt 2743 Tire Carrier
2007-2018 JK
(Kit # 9002-8808)
Items Included in the Kit
Camera Mounted to Tire Carrier Bracket
Chassis Harness (23’ length)
Power Harness
4-pin to RCA Harness
These Instructions
Required Tools & Supplies
T15 & T20 Torx Bits
7mm & 10mm Sockets
Phillips Screwdriver
Plastic Trim Removal Tool
Soldering Iron, Solder, & Heat Shrink Tubing
(RECOMMENDED) or T-taps as an alternate
splicing method
Electrical Tape
NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color
instructions, as well as an installation video, please visit www.brandmotion.com
INSTALLATION(INSTRUCTIONS(
9002-8808.docx Page 2 of 6 JM
Install
Step 1: Remove spare tire.
Step 2: Insert connector from Camera connector
through the rear gate vent behind tire carrier. Make sure
to leave about 6” of slack hanging out of the opening to
connect the camera to.
Step 3: Using a plastic trim removal tool, remove
interior panels on inside of rear gate.
Step 4: Pull harness through the rear gate openings.
Step 5: Use Wire Ties to secure Chassis Harness to
existing harness.
Step 6: Use supplied Wire Ties to secure Chassis
Harness to fabric factory wire cover. CAUTION: Leave
enough slack to allow gate to open fully.
Step 7: Use a T20 Torx bit to remove subwoofer box.
(If equipped.)
INSTALLATION(INSTRUCTIONS(
9002-8808.docx Page 3 of 6 JM
Step 8:Using a plastic trim removal tool, pry off rear
seat belt closeout.
Step 9:Using a plastic trim removal tool, remove rear
access panel to expose 10mm bolt, and remove bolt.
Step 10: Pull out subwoofer box slightly to gain access
to run Chassis Harness along existing harness
Step 11: Pull back carpet and continue running Chassis
Harness forward.
Step 12: Run Chassis Harness under B-pillar cover to
passenger doorsill. Use a plastic trim removal tool to
remove the (2) plastic push pins and remove passenger
sill plate/kick panel.
Step 13: Remove rubber bin insert from top of dash.
INSTALLATION(INSTRUCTIONS(
9002-8808.docx Page 4 of 6 JM
Step 14: Remove 7mm bolt .
Step 15:Using a plastic trim removal tool, remove
window switch panel.
Step 16: Disconnect harness from window switches.
Step 17:Remove 7mm bolt.
Step 18:Remove driver knee bolster cover.
Step 19:Remove (2) 7mm bolts on both sides of the
steering column.
Step 20: Remove center stack/cluster surround.
INSTALLATION(INSTRUCTIONS(
9002-8808.docx Page 5 of 6 JM
Step 21: Remove glove box for access and run Chassis
Harness toward center of dash.
Step 22: Using a plastic trim removal tool, remove
HVAC panel.
Step 23: Connecting Power harness.
Splice Red power wire to Blue/Red wire on back of
power point and Splice Black Ground to Black/White
wire. RECOMMENDED: Use solder and cover with heat
shrink tubing or use T-taps as an alternate connection
method.
Step 24: Connect Chassis Harness to RCA Harness.
Step 25: Plug the Chassis Harness RCA connector into
your aftermarket display.
Step 26: Reinstall your spare tire onto the tire carrier,
but do not mount with lock down bar.
Step 27: Put the supplied camera mount on to the
factory tire hold down piece.
INSTALLATION(INSTRUCTIONS(
9002-8808.docx Page 6 of 6 JM
Step 28: Mount the 2 pieces with the lock down bar to
the spare tire carrier. Run the camera wire through the
opening of the spare tire.
Step 29: Connect to 4-pin connectors together inside
the tire carrier by reaching around the spare tire.
Step 30: Make sure tire lock down bar is in the correct
location.
Step 26: Test the system. Start vehicle and shift into
Reverse in order to check that all connections were
made properly. If all of the connections are correct you
will see the camera image displayed on your aftermarket
display.
Step 27: Reassemble vehicle. Follow your disassembly
steps in reverse order, taking care not to bind the
harness wiring when reinstalling trim.
Step 31: Reassemble vehicle. Follow your disassembly
steps in reverse order, taking care not to bind the
harness wiring when reinstalling trim.
Table of contents
Other BrandMotion Dashcam manuals
BrandMotion
BrandMotion AHDS-7812 User manual
BrandMotion
BrandMotion FLEETWORKS FLTW-7603 User manual
BrandMotion
BrandMotion FleetWorks FLTW-7637 User manual
BrandMotion
BrandMotion 9002-8848 User manual
BrandMotion
BrandMotion 9002-8848 User manual
BrandMotion
BrandMotion 9002-7752 User manual
BrandMotion
BrandMotion 9002-2906v2 User manual
BrandMotion
BrandMotion 9002-8722 User manual
BrandMotion
BrandMotion SUTV-1010V2 User manual
BrandMotion
BrandMotion 9002-7802 User manual
