BOXLIGHT Seattle X30N User manual
NE 151 Highway 300, Suite A
PO Box 2609
Belfair, WA 98528
360.464.2119
www.boxlight.com
Seattle X30N
About the Owner’s Manual
Features
Please read the owner’s manual thoroughly to ensure correct usage of the projector and its
features.
After reading, store the owner’s manual in a safe place for future reference.
1. Dress up Design
2. Designed for tough environment
3. Side change lamp
6LGHFKDQJH¿OWHU
5. Quick off
6. Advanced Anti-theft features
7. Five auto features (Auto Search, Auto Sync, Auto Ceiling, Auto Keystone and Auto
Filter Alert)
8. Seven display modes (Natural, Cinema, User, Green board, White Board, Black Board
and Daylight)
9. Built-in 8W speaker
10. Logo capture
11. Image freeze function
12. Digital zoom adjustment
The content of this manual is subject to change without previous notice.
All rights reserved.
Issue of edition 0809.10_01
Projector
Control Panel Window Introduction
49
Control Panel Window Introduction
n
Power Control
Icon Name
Power on
Power off
o
Input Source
Icon Name
Video
S-Video
Y,Pb,Pr
DVI-I
RGB 1
Change Input Source
p
Function Key
Icon Name Icon Name
Up Freeze
Down Blank
Left Keystone Correction +
Right Keystone Correction -
Menu Increase Brightness
Auto Sync Decrease Brightness
Mute Higher Contrast
50
Control Panel Window Introduction
p
Function Key
Icon Name
Lower Contrast
Zoom In
Zoom Out
Volume Up
Volume Down
q
Projector Status
Icon Name
System Status
Input Source Status
Lamp Timer
Air Filter Timer
51
Control Panel Window Introduction
n
Network Control Window introduction
Icon Name Description
Scan all Capture the projector information 1 time only.
Start Auto Scan According to the system setting, get the projector
information automatically.
Stop Auto Capture
Auto Search Search the projector in the same network to
register and modify the setting.
Open Project File 2SHQSURMHFW¿OHZKLFKZDVVDYHG
Save Project File Save the registered projector in this project.
System Setting Setting the projector system remind message.
About Icon content description.
Exit Exit the Network software.
Register projector
Exit
Maintenance Of Projector
52
Maintenance of Projector
Air Filter
:KHQDZDUQLQJPHVVDJHDSSHDUVWRUHPLQG\RXWRFOHDQWKHDLU¿OWHU
please replace a new one as soon as possible. Please check and clean the
DLU¿OWHUSHULRGLFDOO\
Replacing the Air Filter
:KHQWKHXVHWLPHUHDFKHVWKH¿OWHUFRXQWHUWLPHWKHSURMHFWRUZLOO
GLVSOD\DPHVVDJHWKDWLQGLFDWHVWRUHSODFHDQHZ¿OWHU,IWKHUHLVQRVSDUH
DLU¿OWHUDYDLODEOHSOHDVHFRQWDFW\RXUGHDOHU
7XUQRIIWKHSURMHFWRUDQGXQSOXJWKHSRZHUFRUG$OORZWKHSURMHFWRUWRVXI¿FLHQWO\
cool down.
n
5HPRYHWKH¿OWHUFRYHUIURPWKHULJKWVLGHRISURMHFWRU
o
3XOORXWWKHDLU¿OWHU
p
,QVWDOODQHZDLU¿OWHU
q
3XWWKH¿OWHUFRYHURQ
r
5HVHW¿OWHUWLPHUDIWHUFOHDQLQJRUFKDQJLQJDLU¿OWHU3
Up
New one
3OHDVHFOLFNKHUHLI\RXUSURMHFWRULVZLWKKLJKHI¿FLHQF\¿OWHU
53
Maintenance of Projector
Lamp
1. If you want to replace new lamp, but the projector was just turned off,
please let the projector cool down and unplug power cord at least 60
minutes.
2. If the projector is mounted in the ceiling, contact your dealer to replace
the lamp.
Replacing New Lamp
1. Remove the lamp door.
2. Loosen 2 screws of the lamp holder. Take the handle on the top of the
lamp, pull out the lamp straight off the projector.
,QVHUWQHZODPSORFNWKHODPSGRRU¿UPO\ZLWKVFUHZV
4. Put the lamp door on.
5. Please reset the lamp timer after replacing lamp. (P.34)
ACIN
3OHDVHFOLFNKHUHLI\RXUSURMHFWRULVZLWKKLJKHI¿FLHQF\¿OWHU
54
Maintenance of Projector
WARNING
The projector uses a high-pressure mercury lamp.
The explosion of lamp with a loud bang or burn out could possibly cause
LQMXU\RUD¿UH
:KHQWKHEXOEEXUWVLWLVSRVVLEOHIRUVKDUGVRIJODVVWRÀ\LQWRWKHODPS
housing; and for gas containing mercury to escapefrom the projector’s
vent holes.
If the lamp has broken, do not check the inside of the projector. Please
ventilate the room immediately.
Do not touch or bring your face close to the broken pieces since it might
get into your eyes or mouth. In case of injury, seek medical advice
immediately.
Disposal of a Lamp
Dispose of a lamp in accordance with the local recycling laws.
Do not put it to your trash.
Recycling Lamp’s laws of the USA, go to www.lamprecycle.org.
Recycling Product’slaws of USA, go to www.eiae.org.
Recycling Product’slaws of Canada, go to www.epsc.ca.
For more information about recycling laws, please contact local
government agency or dealer
CAUTION HOT
Before replacing the Lamp part, pay attention to the following items:
1.The Lamp is optional part. Contact the dealer for replacement lamp.
2.The lamp becomes very hot when in use. Turn the power off and
disconnect the power cord.
3.Wait 1 Hour before replacing the lamp.
4.Do not use old lamp part.
55
Maintenance of Projector
Other Care
Cleaning The Lens
If the lens is dirty and dusty, display quality maybe decreased. Before
cleaning the lens, please make sure that the projector is cool down
adequately.
After the projector has cooled down adequately, lightly wipe the lens with
the available lens-cleaning cloth.
Do not touch the lens directly with your hand.
Additional
-In order to ensure the safe use of your projector, please contact your
dealer to inspect about once a year.
-Before maintenance, make sure the power cable is unplugged, allow the
SURMHFWRUWRFRROVXI¿FLHQWO\7KHKLJKWHPSHUDWXUHVWDWHRIWKHSURMHFWRU
could cause a burn in and/or malfunction to the projector.
-Never try to maintain the inside of the projector by yourself
Troubleshooting
56
Troubleshooting
Indicator
The power and lamp indicators show the status of the projector. Before requesting repair,
check the projector status using the chart below. If the problem cannot be resolved,
contact your dealer.
In normal status~~~
POWER LAMP CONDITIONS DESCRIPTION
Blinking In
Green Off Stand by mode Projector is ready to be turned on.
Lighting In
Green Off On mode Projector is on and operating.
Lighting In
Green
Blinking In Red
( Slow ) Cool down mode Projector is in cool down mode
and will not respond to user input.
In abnormal status~~~
POWER LAMP CONDITIONS DESCRIPTION
Blinking In
Green
Blinking In Red
( Fast ) Fan fault mode
The projector has detected a
problem of a slow internal fan
speed. The lamp will shut off
automatically. Contact your
dealer.
Blinking In
Green Lighting In Red Lamp cover open
The lamp cover is open or there
is a problem with the lamp. If the
lamp door is closed and replacing
the lamp does not correct the
issue, contact your dealer.
Blinking
In Green (Fast)
Blinking In Red
( Fast ) High temperature
The projector has overheated and
shut itself down.
Correct the over temperature
condition immediately.
1. Check that the ventilation slots
are free from obstructions.
2. Check the cleanliness of the air
¿OWHU
Blinking In
Green (Slow)
Blinking In Red
(Slow) Lamp fail
The lamp does not light. Come
back to “ stand by mode ”, and
press the power button.
Other manuals for Seattle X30N
1
Table of contents
Other BOXLIGHT Projector manuals
BOXLIGHT
BOXLIGHT CP-320tA User manual
BOXLIGHT
BOXLIGHT MP65e User manual
BOXLIGHT
BOXLIGHT CD-753z User manual
BOXLIGHT
BOXLIGHT CP-16t User manual
BOXLIGHT
BOXLIGHT Cinema 13HD User manual
BOXLIGHT
BOXLIGHT SP-5t User manual
BOXLIGHT
BOXLIGHT Studio Experience PREMIERE 30HD User manual
BOXLIGHT
BOXLIGHT CP-19t User manual
BOXLIGHT
BOXLIGHT XD-9m User manual
BOXLIGHT
BOXLIGHT XD-16n User manual
BOXLIGHT
BOXLIGHT SP-48Z User manual
BOXLIGHT
BOXLIGHT CD-850m User manual
BOXLIGHT
BOXLIGHT XD-16n User manual
BOXLIGHT
BOXLIGHT SP-11i Installation and operating manual
BOXLIGHT
BOXLIGHT PRO7501DP User manual
BOXLIGHT
BOXLIGHT CP-306t User manual
BOXLIGHT
BOXLIGHT ProjectoWrite User manual
BOXLIGHT
BOXLIGHT 6000 User manual
BOXLIGHT
BOXLIGHT MP-45 User manual
BOXLIGHT
BOXLIGHT MP-38t User manual
