BOHYUN BY- 6S User manual
Wheel Balancer
BY- 6S
User Manual
Technical performance of BY series tire balancer
-This machine adopts central computer system imported components, high
intelligence, high stability.
-The main shaft of the mechanism is driven by imported bearing, with high
wear-resisting precision and low noise.
-With the most advanced computer drive system, high stability.
-With automatic dynamic and static balance detection function.
-With the function of balancing three kinds of aluminum alloy steel rings.
-It has self - correction and self - diagnosis function.
The machine can be used to balance the lead
1.Code Balancer
(Common steel and aluminium alloy steel rings)
2. Paste Balance Block
(aluminium alloy steel ring)
Note: the weight error of the balance block can directly affect the detection effect of
this machine.
Attention to the Use of Installation Box
1. Do not the tire balancer in extreme temperature and humidity. Avoid placing beside
heating equipment, faucets, air humidifiers or stoves.
2. Don't put the balance machine in front of the window where the sun can directly
enter. In unavoidable cases, curtains, baffles or shields should be used to shield the
balancer.
3. Avoid contact with large amounts of dust, ammonia, alcohol, diluents or spray
adhesives.
4. The balancer should be fixed on a smooth ground. Avoid placement next to air
compressors or objects that may vibrate.
5. Do not approach the machine when using.
6. The specification of the power outlet of the tire balancing machine is 110 v volts
( AC) with a rated output current of at least 10 A( amperes).
7. Tire balancing machine should use a separate power outlet, do not connect other
wires to the power outlet of the balancing machine, and note that the socket must be
reliably connected to the power cord of the balancing machine to avoid human
stampede.
8. Between the back and the wall of the balancer, there should be a distance of 50
CM to ensure good ventilation and heat dissipation.
9. Contact your maintenance service personnel before moving the balance machine.
BY main components of tire balancer
Installation debugging method
1. Switch on and display HLP
2. Press F+FINE key to display the window is lit up
3. Press ALU key to enter the setting program. The current spindle tooth position is
displayed, and the spindle can be rotated forward and backward to check the
phototelex Sensory work.
4. Go to the spindle to 114, press Start, enter the spindle distance setting (the default
value is 195, which can be skipped if it is consistent with the real boundary) and
measure to the outer edge of the spindle flange with a ruler.
Enter the measured value with B + or B -.
Press A + to exit.
5. Go to the spindle -0-, press Start key, enter the spindle zero clearance program,
(this program can clear the spindle since
Press Start key to START the spindle, automatically reset and store and exit.
6. Press C to exit.
7. Put on the tire, input the tire data and then press F+C key to calibrate.
8. Press Start to display Add 100 after starting. Rotate the tire until the outside spot
lights are all on, outside the tire
After hanging 100 grams of lead blocks above the spindle, press START to display
100 ADD. Remove the outside 100 grams of lead blocks, turn the tire to the inside
point lights are all on. After hanging 100 grams of lead blocks above the inside spindle
of the tire, press START to display END CAL.
Balancing machine debugging is over.
Aging of balancing machine
1. Press F+FINE key to display the window is lit up
2. Press ALU key to enter the setting program. The current spindle tooth position is
displayed, and the spindle can be rotated forward and backward to check the
phototelex Sensory work.
3. Turn to the spindle to 100 and press Start to enter the aging procedure for 100
times.
Press START
Key after startup and count to start 100 times after the end of the buzzer prompt.
Balancing machine self check
1. Press F+FINE key to display the window is lit up
2. Press ALU key to enter the setting program. The current spindle tooth position is
displayed, and the spindle can be rotated forward and backward to check the work of
the photoelectric sensor.
Forward loops are added from 0 to 127, and reverse loops are reduced from 127 to 0.
You can also check the red light on the photoelectric plate, slowly turn the spindle, and
the red light will flicker alternately.
3. Press ALU button again to enter the pressure sensor detection.
The values of about 60 to 70 are displayed on both sides respectively. When the
spindle is pressed by hand, the values on both sides will change, which proves that
the two sensors work normally.
BY series tire balancer standard accessories
screw
Width measuring calipe
Quick change of nuts
Balance block disassembly clamp
Optional accessories for BY series tire balancer
shield
Special - made large cone
Special - made fl ange
Standard Annex for Tire Balancer (List)
Balance block disassembly clamp 1
Width measuring caliper 1
Axial - positioning cone 4
Quick - change nut 1
Balancer Lead Screw 1
Basic operation of tire balancer
1. turn on the power switch on the left side of the machine to display 411, and then the
display 9,10 to A ","8.0".
2. installation of tyres
Select the axis cone matching the center hole of the rim, install it in the center of the
rotating shaft, and lock it with a quick change nut. (The maximum weight of the wheel
must not be greater than 70 Kg).
3. input A value data.
Pull the A ruler to the position of the rim mounting balance block and press
push-button，enter the data on the pull ruler into the display 10, where the display 9 is
A"
4. Enter the L value data
Measure the width of the cali per in the attachment , press the button to input
the data on the cali per into the display , when the display is " L"
5. input D value data
After confirming the rim diameter, press the button to enter the data into the
display 10, where the display 9 is D"
6. press the start button
Start operation, a few seconds later, the machine automatically stops.
(B type pull down shield, can run automatically. )
7. shows imbalance
At this point the number of display 9,10 is the tire imbalance, with the hand to turn the
wheel, positioning constantly flashing.
8. until (11),(12) one of the indicator lights are fully lit, indicating that the highest rim is
an unbalanced point at this time, where (11) represents the inner side point of the rim
and (12) represents the outer side point of the rim.
9. the corresponding balance block measured by the display at the rim imbalance
point, the display 9 represents the inner side of the rim and the display 10 represents
the outer side of the rim.
10. Repeat the operation steps 6 to 9 until 9,10 shows "00".
11 . Remove the wheel from the balance rotation shaft and end the operation
procedure .
Function Select
When this light is on, it is suitable for other tires on both sides of motorcycle tires or
rims which can not be balanced
When this light is on, it is suitable for the alloy ring tire with the balance block attached
to the shoulder of the rim.
When the light is on , the outside of the rim and the clip balance block on the inside .
When this light is on, it is suitable for the alloy ring tire which is pasted on the outer
side of the alloy rim.
When the four sets of indicators are out , the standard balance mode (the computer is
automatically set each time it is turned on) .
BY Series Balance Computer Self-Def code
1. no rotation signal, motor does not turn or position sensor position is wrong, sensor
bad and plug contact, computer board bad, etc.
2., the coil speed is less than 60 rpm, during the measurement of the computer phone.
Too loose and too tight tires and belts can cause errors.
3.the calculation error, the unbalanced amount exceeds the operation range.
4. motor reversal, position sensor wiring error.
5. press the start key, the protective cover is open.
6. self - calibration errors or self - calibration data loss requires re - calibration .
7. data memory content is lost or damaged.
8. a self-calibration error, it may be the second rotation without adding 100g of
balance or Pressure sensor cable broken, pressure sensor broken, plug contact poor.
Table of contents
Popular Wheel Balancer manuals by other brands
Hofmann
Hofmann geodyna 6900-2p Operation manual
CEMB
CEMB K22 Use and maintenance manual
Hofmann
Hofmann POWER CLAMP features Additional instructions
Desoutter
Desoutter Industrial Tools DU Series user manual
HPA-Faip
HPA-Faip B 235 Evo Operator's manual
Hofmann
Hofmann megaspin 300 Operating instructions manual
