Boge airtelligence PROVIS User manual
Operating
instructions
Control for
several compressors
airtelligence PROVIS
BOGE Operating instructions for airtelligence PROVIS
Inhalt.pm6.5 - GB
Page I
Operating instructions
airtelligence
PROVIS
Issue: 11/2008
No. 596.0899.01
Nominal price: €5,00
BOGE KOMPRESSOREN
Postfach 10 07 13
D-33507 Bielefeld
Otto-Boge-Straße 1–7
D-33739 Bielefeld
Fon: ++49 / 52 06 / 6 01-0
Fax: ++49 / 52 06 / 6 01-200
Mail: info@boge.com
Net: www.boge.com
Page II BOGE Operating instructions for airtelligence PROVIS
Inhalt.pm6.5 - GB
BOGE Operating instructions for airtelligence PROVIS
Inhalt.pm6.5 - GB
Page III
Index
Index
1.1 General safety instructions ........................................................ 1.1
1.1.1 Safety instrutions for operation the control .................................... 1.1
1.1.2 Safety instructions for servicing and repairing the control ............. 1.1
1.2 Introduction ................................................................................. 1.2
1.2.1 Correct use.................................................................................... 1.3
1.2.2 Inadmissible use ........................................................................... 1.3
1.2.3 Transport damage .........................................................................1.4
1.2.4 Customer service .......................................................................... 1.4
1.3 Product description .................................................................... 1.5
1.3.1 Installation and adjustment............................................................ 1.5
General
Page IV BOGE Operating instructions for airtelligence PROVIS
Inhalt.pm6.5 - GB
Allgemein.pm6.5 - GB
Page 1.1
General
BOGE Operating instructions for airtelligence PROVIS
Nonobservance of the following safety instructions may lead to injuries
and damage to the control.
Also observe the generally valid safety and accident prevention regu-
lations in addition to the information in these operating instructions!
1. Ensure that no commissioning and maintenance work on the controlis
undertaken until these operating instructions are understood.
2. Only use the control for its intended use, as described in these operating
instructions.
3. The owner must ensure
– that only appropriately trained and authorized personnel work on this
control.
– that the operating, maintenance and repair personnel has been
made fully familiar with all safety instructions, and that they are being
observed.
– that the control is only operated in a safe operating condition.
4. Only operate the compressor using the additional equipment (options)
recommended or authorized by the manufacturer.
5. Never start the control when one or serveral parts (e.g. cable, plug) are
damaged, when not in perfect working order, when damage is detected
or suspected.
1. Ensure that maintenance work is only carried out by appropriately
trained persons.
2. Ensure that setting work, malfunction rectification and repair is only
carried out by qualified electricians (see DIN VDE 0100 or DIN VDE
0013 EN 60204).
3. Prior to maintenance or repair work:
– Switch off the main switch.
– Check that no parts are under voltage.
4. Work on voltage carrying parts and devices are not permitted. Exceptions
are governed by the appropriate regulations, e.g. DIN VDE 0105.
5. Only use original spare parts, compressor oils and operating materi-
als released by BOGE during repair or maintenance.
1.1.1
Safety instructions
for operation
of the control
1.1.2
Safety instructions
for servicing and
repair of the control
General safety instructions1.1
Page 1.2
Allgemein.pm6.5 - GB
General
BOGE Operating instructions for airtelligence PROVIS
The purpose of these operating instructions is to familiarize the user with the
function and all application possibilities of the control.
These operating instructions contain important information on how to operate
several compressors safely, economically and according to intended use,
with the aid of an MCS control.
Observing these operating instructions will assist in avoiding danger, to
reduce repair costs and down times and to increase the reliability and service
life of the compressors.
It contains important information concerning the required parameters and
settings, and assists in case of malfunctions.
The operating instructions must be available to the control and compressor
operating personnel at the place of operation, at all times.
The operating instructions must be carefully read and applied by all persons
engaged to undertake the following work on the compressor:
– Operation, including fault rectification
– Commissioning
Introduction1.2
1.2
Correct use
Allgemein.pm6.5 - GB
Page 1.3
General
BOGE Operating instructions for airtelligence PROVIS
1.2.1
Correct use
This BOGE multiple system control including its options is intended for the
control of several screw and piston compressors.
It may only be operated and adjusted by trained and authorised people.
Requirements for compressors to be controlled
If the master control is ordered with compressors, we install the interface in
the compressors in the factory (forced option). If the compressors are already
installed, it will be necessary to meet the requirements for the master control.
These are normally:
1. A potential-free contact "Ready" (2 terminals)
2. Two terminals in series with the pressure switch installed in the compres-
sor.
3. A potential-free contact "Operation" (2 terminals).
4. A potential-free contact "Fault" (2 terminals).
For compressors with proportional control or frequency control please
contact BOGE.
Care must be taken with other makes; always obtain approval from the
factory.
This BOGE control is not explosion protected.
Do not operate in explosive areas!
The following is not permitted:
– Exceeding or going below the specified operating voltages
– Operation of the control by unauthorized or untrained persons
– Connection of unsuitable compressors
– Too high room temperatures > 45°C
1.2.2
Inadmissible use
Introduction1.2
Page 1.4
Allgemein.pm6.5 - GB
General
BOGE Operating instructions for airtelligence PROVIS
BOGE does not accept any liability for breakage or transport damage.
Please inspect the compressor immediately after delivery and direct damage
claims to the last haulier – even when the packing is not damaged!
To safeguard claims against the haulier we recommend leaving the machine,
devices and packing material in the same condition as they were in when
the damage was detected.
In the event of any other complaints, please inform us within six days after
arrival of the delivery.
The BOGE customer service is, of course, at your disposal.
Please contact us on:
Telephone: ++49 / 52 06 / 6 01-0
To avoid delays, always specify the following details about your control:
1. Software version
2. Circuit diagram number
3. Job number
4. Machine number
5. Type
6. Year of manufacture
ATTENTION!
Only BOGE service technicians or persons authorized by BOGE in writing
may repair or alter the control during the warranty period. Otherwise all
warranty claims will expire!
1.2.3
Transport damage
1.2.4
Customer service
Introduction1.2
Table of contents
Other Boge Control Unit manuals
Popular Control Unit manuals by other brands
Festo
Festo Compact Performance CP-FB6-E Brief description
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Quick installation guide
JS Automation
JS Automation MPC3034A user manual
JAUDT
JAUDT SW GII 6406 Series Translation of the original operating instructions
Spektrum
Spektrum Air Module System manual
BOC Edwards
BOC Edwards Q Series instruction manual
KHADAS
KHADAS BT Magic quick start
Etherma
Etherma eNEXHO-IL Assembly and operating instructions
PMFoundations
PMFoundations Attenuverter Assembly guide
GEA
GEA VARIVENT Operating instruction
Walther Systemtechnik
Walther Systemtechnik VMS-05 Assembly instructions
Altronix
Altronix LINQ8PD Installation and programming manual
