body Power BR2710 User manual
BR2710
OWNER’S MANUAL
* This item is for consumer use only and it is not meant for commercial use.
OWNER’S MANUAL
* This item is for consumer use only and it is not meant for commercial use.
This page intentionally left blank
General Information
BR 2710 Page 1
Warranty
Body Flex Sports warrants your product for
a period of 1 year for the frame and 90 days
on all parts if the item is used for the intended
purpose, properly maintained and not used
commercially. Any alterations or incorrect
assembly of the product will void this warranty.
Proof of purchase must be presented for any
warranty validation (no exceptions). This
warranty applies to the original purchaser only
and is not transferable.
This warranty does not cover abuse or defects
caused during use, storage or assembly.
During the warranty period, Body Flex Sports
reserves the right to:
a). provide replacement parts to the
purchaser in an effort to repair the item.
b). repair the product returned to our
warehouse (at the purchaser’s cost).
c). replace the product if neither of the two
previously mentioned actions effect repair.
This warranty does not cover normal wear and
tear on upholstery.
Questions
If you have any questions concerning the
assembly of your item or if any parts are
missing, please DO NOT RETURN THE
ITEM TO THE STORE OR CONTACT THE
RETAILER. Our dedicated customer service
staff can help you with any questions you may
have regarding the assembly of this unit and
can also mail you replacement parts.
Customer Support
Customer Support is open 9:00 a.m. to 5:00
p.m. (Pacific Time) Monday through Friday.
Please contact us by any of the following
means.
Body Flex Sports, Inc.
21717 Ferrero Parkway, Walnut, CA 91789
Telephone: (888) 266 - 6789
Fax: (909) 598 - 6707
Email: info@bodyflexsports.com
Safety
Before you undertake any exercise program,
please be sure to consult with your doctor.
Frequent strenuous exercise should be
approved by your doctor and proper use
of your product is essential. Excessive or incorrect
training may result to health injuries. Please read
this manual carefully before commencing the
assembly of your product or starting to exercise.
• Please keep all children away from this item
when in use. Do not allow children to climb or
play on them when they are not in use.
• Supervise teenagers while they use this unit.
• For your own safety, always ensure that there
is at least 3 feet of free space in all directions
around your product while you are exercising.
• Regularly check to see that all nuts, bolts and
fittings are securely tightened. Periodically
check all moving parts for obvious signs of
wear or damage.
• Clean only with a damp cloth, do not use
solvent cleaners. If you are in any doubt, do
not use your product; contact CUSTOMER
SUPPORT.
• Before use, always ensure that your product
is positioned on a solid, flat surface. If
necessary, use a rubber mat underneath to
reduce the possibility of slipping.
• Always wear appropriate clothing and
footwear such as training shoes when
exercising. Do not wear loose clothing that
could become caught in moving parts during
exercise.
• Do not use this unit if it is not functioning
properly or if it is not fully assembled.
• Do not use this unit for commercial purposes.
This unit is for home use only.
Storage and Use
Your product is intended for use in clean
dry conditions. You should avoid storage in
excessively cold or damp places as this may
lead to corrosion and other related problems.
Weight Limit
Your product is suitable for users weighing:
300 pounds or less.
• Before use, you must read and understand all
instructions & warnings stated in this Owner’s
Manual as well as posted on the equipment.
• It is the facility owner’s responsibility to properly
instruct users on the proper operation of the
equipment and to warn them of the potential
hazards.
• If at any time during exercise you feel faint, dizzy
or experience pain, stop and consult your
physician.
Assembling Tools
- Ruler with both metric and English measurements
- 2 x Adjustable Wrenches
- 1 x Philips (”Crosshead”) Screw Driver
•
Any adjustment devices that could interfere with
the user's movement on this unit should not be
left projecting.
Page 2
pre-assembled
12
#60
pre-assembled
59. Special Washer
pre-assembled
Hardware List
The following hardware is used to assemble your unit. Please take a moment to familiarize yourself with these items.
PLEASE NOTE: some of these parts may have already been pre-assembled on your unit.
BR 2710
pre-assembled
Page 3
BRM 3670 Stride Cycle Page ?
# Description # Description
1 Main Frame 29L/29R Left/Right Lower Handlebar
2 Rear Stabilizer 30 Bolt (M8x15 mm)
3 Adjustable End Cap 31 Front Post
4 Carriage Bolt (M8x73 mm) 32L-1/32L-2 End Cap
5 Arc Washer (M8 R30.5) 33 Spacer (φ32xφ19.2x67mm）
6 Cap Nut (M8) 34 Computer
7 Front Stabilizer 35 Arc Washer (M8 R16)
8 End Cap 36 Carriage Bolt (M8x40 mm)
9 Screw (M3x15 mm) 37 Big Washer (M8)
10L-1/10L-2 End Cap 38 Spring Washer (M8)
11L/11R Left/Right Pedal Arm 39 Hex Bolt (M8x15 mm)
12 Bushing (φ28xφ19x24.5) 40R-1/40R-2 End Cap
13 Big Washer (M10) 41 Screw (M4x8 mm)
14 Nylon Nut (M10) 42 Washer (M5)
15 Plastic Spacer (φ31.8xφ19.2x36) 44 Water Bottle Holder
16 Nylon Nut (M8) 45 Water Bottle
17 Washer (M8) 46L/46R Left/Right Upper Handlebar
18L/18R Left/Right Pedal 47 Foam of Upper Handlebar
19 Hex Bolt (M8x45 mm) 48 End Cap
20 Screw (M4x20 mm) 49 Steel Plate of Handle Pulse
21L-L/21L-R End Cap 50 Foam of Middle Handlebar
22 Hex Bolt (M8x75 mm) 51 Washer (M6)
23 End Cap 52a/52b Handle Pulse Wires
24a Sensor Wire (Lower) 53 Middle Handlebar
24b Sensor Wire (Middle) 54 Cover of Handlebar
24c Sensor Wire (Upper) 55 Bolt (M8x30 mm)
25 Bushing (φ28xφ14x24) 56 Screw (M4x19 mm)
26 Spacer (φ14xφ8x59) 57 End Cap
27R-1/27R-2 End Cap 58 AC Adapter
28R-L/28R-R End Cap 59 Special Washer
60 Screw (M4x12 mm)
BR 2710
Parts Listing
The following parts list describes all of the parts illustrated on the
exploded diagram on the following page. Please note, most of
these parts are already pre-assembled on your unit.
Page 4 BR 2710
The following diagram is provided to help you familiarize yourself with the parts and
hardware that will be used during the assembly process. Please note that not all of the
parts and hardware you see here will be used while you are assembling the machine
because some of these items are already pre-installed. Please continue to the next
page to begin the assembly process and use this page only as a reference guide for
parts and hardware.
Exploded Diagram
Page 5
Assembly Instructions
Hardware RequiredAssembly Step 1
Stabilizer Assembly
Secure the Front Stabilizer (#7)and Rear
Stabilizer (#2)to the Main Frame (#1) by
using four Carriage Bolts (#4), four Arc
Washers (#5) and four Cap Nuts (#6)
BR 2710
Page 6
Assembly Instructions
Assembly Step 2 Hardware Required
Front Post Assembly:
A.With the help of an assistant, connect the
Sensor Wire (Lower) (#24a) to the Sensor
Wire (Middle) (#24b).
B.Secure the Front Post (#31)to the Main
Frame (#1) by using four Bolts (#30)and
four Washers (#17).
BR 2710
Page 7
Assembly Instructions
Hardware Required
#59. Special Washer
[4 peices]
Assembly Step 3
Lower Handlebar Assembly:
The two Spacers (#33) and Special Washers (#59) are
already pre-assembled on the two bars that are protruding
from the Front Post (#31).Ensure that they are properly
in place as indicated in the assembly below.Slide the Left
Lower Handlebars (#29L)
with the longer end of the shaft
towards the center of the Front Post (#31). Then secure it
with one Big Washer (#37), aSpring Washer (#38) and
aHex Bolt (#39). Repeat this process on the other side.
Pedal Arm Assembly:
The Plastic Spacer(#15) and the Special Washer (#59)
are already pre-assembled.Ensure that they are properly
in place as indicated in the assembly below.Slide the Left
Pedal Arm (#11L) into the Crank Stud and secure it with
one Big Washer (#13) and a Nylon Nut (#14) as shown
in the assembly below.Repeat this process on the
opposite side.
Before attaching the Left Lower Handlebar (#29L) to the
Left Pedal Arm (#11L),
remove the zip tie at the bottom of
the Left Lower Handlebar (#29). Then attach the Left
Lower Handlebar (#29) to the Left Pedal Arm (#11) and
secure it with a Hex Bolt (#22), a Washer (#17) and a
Nylon Nut (#16).
Repeat this process on the opposite side.
BR 2710
Page 8
Assembly Instructions
Assembly Step 4Hardware Required
Upper Handlebar Assembly :
Attach the Upper Handlebars (#46L & #46R)
to the Lower Handlebars (#29L & #29R)and
secure them with four Carriage Bolts (#36),
four Arc Washers (#35)and four Cap Nuts
(#6).
Attach the snap-on End Cap (#32L-1, 32L-2)
to the left Left Lower Handlebar (#29L).Align
the two together and press firmly until it snaps
into place.
Repeat this process on the opposite side.
BR 2710
Table of contents
Other body Power Elliptical Trainer manuals
Popular Elliptical Trainer manuals by other brands
Bonn Germany
Bonn Germany Concept 2.2 user manual
Precor
Precor Resolute RSL 620 Assembly guide
NordicTrack
NordicTrack E 9.2 Elliptical HASZNALATI UTASITAS
Vision Fitness
Vision Fitness X6600iNetTV Assembly guide
Matrix
Matrix MX-A5x owner's manual
SportsArt Fitness
SportsArt Fitness ECO-NATURAL Elite E874 owner's manual
