Bodart & Gonay Scope Specification sheet

Scope 1

Scope

Instructions for use and

maintenance

07DHSCOA

Attention: Remove the instructions from the ﬁreplace and give them to the client,

along with the necessary instructions (explanations and demonstrations).

2 Scope

MEMO

(to be completed by the installer)

* SCOPE APPLIANCE

* REFERENCES:

- Left corner:

- Right corner:

* DATE OF PURCHASE: ..... / ..... / .....

* SERIAL NUMBER:

(visible on the ﬁreplace’s identiﬁcation label, see

page 4 no.11 Description of elements)

...................................................................................................

* DISTRIBUTOR:

Name ..................................................................

Street / No. ........................................................

Town ...................................................................

Post code...........................................................

Tel. ........................................................................

Note:

Your supplier is the specialist chosen by BODART & GONAY to represent your region.

For your safety and satisfaction, we recommend that you have them carry out your installation.

All local and national regulations and European standards must be observed when installing and using the

appliance.

If, however, you wish to carry out the installation yourself, to avoid any surprises, we recommend that you:

- consult the terms of our guarantee agreement,

- seek advice from your supplier.

Concerning installation, given the impossibility of covering every particular case that might arise, we will conﬁne

ourselves to the most important points.

Dear Client,

We congratulate you on the purchase of your Bodart & Gonay ﬁreplace.

We are happy to inform you that you have chosen a quality product wholly designed and manufactured by our

company, using the most up-to-date production techniques.

To get the best use out of your appliance, we strongly recommend that you read these instructions carefully and

keep them safe.

Also keep your proof of purchase safe, as it will be used to determine the guarantee period.

We wish you lots of pleasure and warmth around your Bodart & Gonay ﬁreplace.

Customer Services

Scope 3

OK!

TABLE OF CONTENTS

RECOMMENDATIONS

1. Fuel 3

2. First ﬁre 3

3. With each ﬁre 3

1. Use: 4

1.1. Description of elements 4

1.2. Opening - closing the ﬁreplace 5

1.3. Fire behaviour 5

1.3.1. Lighting 6

1.3.2. Ideal rate 6

1.3.3. Reduced rate 6

1.4 Fans and speed variator 7

2. Maintenance: 8

2.1. Everyday maintenance 8

2.2. Annual servicing 9

3. Spare parts 10

4. Faults 11

5. Guarantee 12

RECOMMENDATIONS

1. Fuel:

This appliance burns (well dried!) wooden logs and

logs of compressed wood shavings.

Do not put too much wood in at once.

This appliance may not under any circumstances be

used as an

incinerator!

2. The ﬁrst ﬁre:

- Bakes the paint, which causes a release of fumes.

- Put the fans on maximum speed to disperse them (for around 12 hours).

Ventilate the room!

Do not touch the paint until the ﬁreplace has cooled down as initially it softens,

then hardens for good.

3. With each ﬁre you must:

- Close the door of the ash box.

- Position the grill properly.

- Turn on the fan.

4 Scope

1. The gate: Never leave it open when the

appliance is in operation. Always close it before

opening the door. Never open it when the door is

open.

1.Use:

1.1. Description of elements

2. The thermostat: It regulates the quantity of pri-

mary air for combustion according to its position.

Its valve closes and opens according to the tem-

perature of the combustion chamber. Its control

knob is telescopic to facilitate operation.

3. The ashtray door: It gives access to the ashtray

and to the deashing arm. It must always be closed

during a ﬁre (otherwise the combustion air is no

longer under control and the ﬁre ﬂares up →ove-

rheating of appliance).

4. The deashing arm: To use it, pull it towards you.

It is used to adapt the ﬁreplace to the type of fuel

(left-hand position: open grill for coal; right-hand

posi¬tion: closed grill for wood). Deashing is

done by moving it from right to left.

5. The ashtray: In the form of a shovel to enable

collection of ashes right at the bottom of the

appliance. Monitor the amount of ash in the ash-

tray and empty it before it overﬂows.

7. Door lock and removable handle: With the gate

closed, place the removable handle in the hole in

the door to open and close the door.

8. The closing lever: This lever must be operated to

close the gate.

9. The microswitch: A switch that automatically

stops the fan on opening the door.

10. The fan ﬁlters: They stop the fans clogging up

and stop dust from circulating. They can be remo-

ved for cleaning without the use of a tool.

11. Fireplace identiﬁcation label.

6. The pair of grills: The upper grill is made of spe-

cial heat-resisting steel. The lower grill is made of

heat-resisting cast iron. The upper grill is operated

by the deashing arm.

12. Refractory bricks: natural material that protects

the heating unit whilst limiting varia¬tions in tem-

perature.

13. The distributor: It enables regular distribution of

primary air.

14. The case: It delimits the convection box.

15. The log guard: For safety. It prevents logs

coming into contact with the glass.

16. The inner door: This is a hardwearing stainless

steel seal, to guarantee airtightness of the door and

trouble-free clearing of smoke from the glass.

17. The baﬄe: Made of heat-resisting stainless steel,

it lengthens the path of fumes optimising secon-

dary combustion and increasing heat transfer.

Scope 5

OK!

18. The variator: It enables adjustment of fan speed.

1. Speed adjustment.

2. Minimum speed adjustment screw under the

knob (factory-calibrated).

3. Fuse (Remove the knob, unscrew the plate,

remove old fuse, replace with identical fuse).

1.2. Opening - closing the door

1.3. Fire behaviour

Quality wood is:

- Dry wood that has been drying for at least 2 years in a ventilated

sheltered area.

- Use logs from broad-leaved trees in preference to those from coni

fers, which tend to burn quickly and produce lots of soot. In order

of preference: hornbeam, oak, beech.

- It is also possible to use logs of compressed wood shavings and

briquettes.

An excessive load of wood leads to:

- A reduction in yield and an increase in wood consumption.

- A signiﬁcant loss of heat through the chimney.

- Premature ageing of the ﬁreplace.

During the ﬁre, open the door slowly. Opening it suddenly

causes a temporary backdraft of fumes.

To close the door: lift the handle, press the door against the

heating unit so that the seal is gently compressed, then lower

the handle until it is locked.

It is normal for the fan to cut out when opening the

door.

A. Cold convection air

B. Hot convection air

W. Combustion air

X. Primary combustion

Y. Secondary combustion (post combustion)

Z. Fumes

The quality and the drying of the wood are of prime

importance for the ﬁreplace to operate at its best

(heater power and yield, cleanliness of glass).

6 Scope

1.3.2. Ideal rate for good yield

1. Choose split logs (1,2 or 3 depending on the quantity of heat needed).

2. Try to pile them in staggered rows to encourage gas exchanges.

3. Put the thermostat on 7-8.

4. Put the fan on maximum .

1.3.1. Lighting

1. Open the air control to maximum: thermostat 9.

Place the grill in open position (lever to the left).

2. Lay ﬁrelighter or crumpled-up newspaper.

Finish oﬀ with kindling.

The use of inﬂammable liquids is prohibited.

Lay 2-3 split logs (depending on size).

3. Set light to it.

4. To avoid condensation of fumes on the glass and to facilitate star

ting the ﬁre: Leave the door slightly ajar to prevent the glass

sooting up, as its still too low temperature causes condensation

and deposit of particles.

5. As soon as there are strong ﬂames and the glass is suﬃciently warm, close the door completely.

6. Start the fan (Variator ON)

7. When the ﬁre is blazing and the appliance is hot, close the grill (lever to the right), close the ashtray

and adjust the thermostat to the required position.

8. Adapt the fan speed to the quantity of hot air you need. But when there is a ﬁre, it must ALWAYS be

turned to at least the minimum.

1.3.3. Reduced rate and long-lasting combustion

The maximum permitted load in one go at reduced rate is 7kg.

1. Keep a 3 to 5 cm bed of embers at the bottom of the ﬁreplace.

2. Choose logs with a very wide section.

3. Position the thermostat according to the draught of your chimney. A redu-

ced rate is generally achieved between 0 and 3. This kind of load can only be

used at reduced rate, to produce a long-lasting ﬁre.

Piling logs in parallel encourages a long-lasting ﬁre. Add more logs when there are only embers left, just

after the last ﬂames die out.

Continuous use at reduced rate may, through condensation, cause an accumulation of soot in the

chimney, and thereby a risk of chimney ﬁre, and dirty the glass more quickly.

For better yield, it is best to have the thermostat on 7-8 and load log-by-log depending

on the quantity of heat you need.

This also enables you to keep the glass, bricks and chimney cleaner.

The maximum permitted load at maximum rate is 4kg/hr

Scope 7

OFF=

MAX.

MINI.

FF= O

MAX.

MINI.

FF= O

1.4. Fans and speed variator

ATTENTION!

When the ﬁreplace is being used, and even if there are no more ﬂames,

certain accessible parts of the appliance are at very high temperatures.

Do not leave children unsupervised near the ﬁreplace.

8 Scope

ATTENTION !

- Do not clean the glass when it is hot.

- Spray the product* on the centre of the glass, then spread it using a cloth or absorbent paper.

- Do not use water and/or cleaning products on the painted areas.

- For stubborn marks, it is possible to use a blade for scraping ceramic hobs.

*We recommend use of the cleaning product “BG Clean”, available from your dealer.

“BG Clean”does not contain caustic soda and is biodegradable.

ASHTRAY DOOR

Check the condition of the seal and if necessary replace it to ensure airtightness.

Check the operation of the spring clip.

AIR DISTRIBUTOR

Where necessary, unblock the air inlet holes.

GRILLS

Make sure that there are no obstacles restricting their movement.

DUST FILTERS

Clean them with a vacuum cleaner and, where necessary, with water. New ﬁlters can be obtained form

your supplier.

THERMOSTAT

Check that it turns properly.

Your supplier is authorised to check the setting.

DOOR

Check that the stainless steel seal is airtight.

If necessary, your supplier can adjust and/or replace it. Check that both the lock and the opening safety

work properly. This is in order to ensure good yield and clean glass.

2. Maintenance:

2.1. Everyday maintenance

GLASS

To clean the glass, open the door using the following procedure.

Scope 9

PAINTING METAL PARTS

Do not use water and/or cleaning products on painted parts.

Stained areas may be restored using special B&G high temperature aerosol paint, which is available from

your dealer.

LUBRICATION

With frequent use, it is recommend that the following parts be lubricated annually:

- door and gate: hinges and lock.

- thermostat: control shaft.

FANS

Disconnect the electricity supply, remove the ﬁlter supports (remove the 2 locking screws), disconnect the

fans then remove them. Clean the impeller blades using a brush (compressed air is prohibited). Reassem-

ble everything.

REFRACTORY BRICKS

A split brick may still play a protective role. However, a missing piece will need to be replaced to maintain

eﬀective protection of the heating unit. Individually, bricks are easily-replaceable wear parts. It is recom-

mended that you change a part that is too damaged.

CHIMNEY-SWEEPING

Have the chimney swept at least once a year, not only to

comply with the law, but also for safety reasons.

- Remove the baﬄe, as shown in the drawing.

- Place the grill in closed position (wood).

- Close the door, thermostat and ashtray door.

- Simply clean up any fallen dust with a vacuum cleaner.

Take advantage of the chimney-sweeping to check the con-

dition of the chimney and connections.

- Reposition the baﬄe following the instructions in reverse.

2.2. Annual servicing

DO NOT USE NORMAL LUBRICANT. At high temperatures the latter will dry out and cause seizing up. If

necessary, clean the surfaces thoroughly, then apply a LUBRICANT RESISTANT TO HIGH TEMPERATURES,

available from your dealer.

10 Scope

3. Spare parts

Table of contents

Other Bodart & Gonay Indoor Fireplace manuals

Bodart & Gonay

Bodart & Gonay Optifire OPTI700 Specification sheet

Bodart & Gonay

Bodart & Gonay PHENIX 1150 Specification sheet

Bodart & Gonay

Bodart & Gonay Phenix Green 75 Operating instructions

Bodart & Gonay

Bodart & Gonay ARGOS Specification sheet

Bodart & Gonay

Bodart & Gonay Cosmos Series Specification sheet

Bodart & Gonay

Bodart & Gonay Infire EASY User manual

Bodart & Gonay

Bodart & Gonay PHENIX Green User manual

Bodart & Gonay

Bodart & Gonay OPTIFIRE 780 Guide

Bodart & Gonay

Bodart & Gonay Jubilee Manual

Bodart & Gonay

Bodart & Gonay CONCEPT Series User manual

Bodart & Gonay

Bodart & Gonay Infire EASY User manual

Bodart & Gonay

Bodart & Gonay Series 603 User manual

Bodart & Gonay

Bodart & Gonay ARGOS Gaz Specification sheet

Bodart & Gonay

Bodart & Gonay Phenix Green User manual

Bodart & Gonay

Bodart & Gonay COSMOS 125 Operating instructions

Bodart & Gonay

Bodart & Gonay PHENIX 1000 Specification sheet

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual