BMW MINI Wallbox Plus User manual
MINI Wallbox Plus
Installation instructions
Freude am Fahren
MINI Wallbox Plus
Installation instructions
Contents
INFORMATION 9
Safety information 9
Intended use 11
About this manual 11
Package 12
Warranty 12
OPERATION 13
Displays and controls 13
SPECIFICATIONS 14
General criteria for selecting an installation site 14
Specifications for the electrical connection 15
INTEGRATION OF EXTERNAL METERS 16
Domestic connection monitoring (post-meter fuse) 16
Installation of external meters 17
INSTALLATION 19
Installation requirements 19
Recommended installation positions 20
Required distance 21
Remove the housing cover 22
Removing the termination panel cover 23
Removing the terminal cover 24
Surface-mounted cable routing - Cable inlet from above 24
Surface-mounted cable routing - Cable inlet from below 25
Cable inlet from behind – cable in the wall 25
Cable openings 26
Mounting the Wallbox 27
ELECTRICS 31
Connection diagram with open termination panel cover 31
Connecting the supply cable 32
Using the supply terminals (spring-type terminal) 33
EN
5
Terminals X1/X2 34
Enable input X1 35
RS485 connection X2 36
Ethernet1 connection X4 37
SETTINGS 39
DIP switch settings 39
COMMISSIONING 44
General commissioning procedure 44
Commissioning mode/Self-test 44
Safety tests 45
RFID authorisation 45
Installing the terminal cover 46
Installing the termination panel cover 46
Install the housing cover 48
MISCELLANEOUS 49
Dimensions 49
Technical data 50
MAINTENANCE 53
Replacing the fuse 53
WASTE DISPOSAL 54
SOFTWARE UPDATE 55
PRODUCT INFORMATION PAGE 56
INDEX 57
6
Legal information
Bayerische Motorenwerke Aktiengesellschaft
Munich, Germany
www.bmw.com
Original installation instructions
Copyright ©2019 BMW AG Munich
This documentation contains information protected by copyright. All rights reserved, especially
the right of reproduction and distribution. No part of this documentation may be reproduced
(photocopying, scanning or any other procedures) or processed, copied or distributed in any form
using electronic systems without the written consent of Bayerische Motorenwerke Aktiengesellschaft.
Contraventions are liable to compensation.
EN
7
About this manual
Keep this manual for the full service life of the product.
Read these instructions carefully and look at the device to familiarise yourself with it before you
attempt to install, operate or service it. The following special information may be displayed in this
documentation or on the device to warn you of possible dangers or point to information which explains
or simplifies a process.
Use the operating manual to operate the Wallbox and to obtain explanations of errors on it.
Keep this manual safe for later use. The latest manuals can be downloaded from the
https://charging.bmwgroup.com/web/wbdoc/ internet at .
Symbols used
You will find information and warnings about possible dangers at various points in the manual. The
symbols used in the manual have the following meanings:
WARNING
Means that death or serious physical injury may occur if the appropriate precautions are not
taken.
CAUTION
Means that property damage or minor physical injury may occur if the appropriate precautions
are not taken.
IMPORTANT
Means that property damage may occur if the appropriate precautions are not taken.
ESD
This warning points out the possible consequences of touching electrostatically sensitive
components.
Note
Indicates procedures which do not involve any risk of injury.
This lightning symbol means a danger of electric shock.
Access for trained, authorised electricians only.
Note
The MINI dealer will be happy to help you find a qualified installation partner.
8
INFORMATION
Safety information
Read the safety information carefully and look at the device to familiarise yourself with it before you
attempt to install, operate or service it.
WARNING
Electrical danger!
The Wallbox must be installed, commissioned and serviced by appropriately trained,
qualified and authorised electricians(1) who bear full responsibility for compliance with
current standards and installation regulations.
Please note that an additional overvoltage protector may be required by vehicles or national
regulations.
Please refer to your national connection and installation standards.
Connect only voltages and circuits to the right-hand connection area (Ethernet, terminals
for control cables) which can be safely isolated from dangerous voltages (for example
through adequate insulation).
Before commissioning, check that all screw and clamp connections are tight!
The terminal panel must never be left open without supervision. Fit the terminal panel
cover when you leave the Wallbox.
Do not make any unauthorised changes or modifications to the Wallbox.
Repair work to the Wallbox is not permitted, and may be completed only by the
manufacturer or a trained expert (Wallbox replacement).
Do not remove any identifiers such as safety symbols, warning instructions, rating plates,
labels or cable markings.
The Wallbox does not have a main switch. The RCCB and circuit breaker for the building
installation can be used as power cut-off device.
Pull the charging cable out of the connector by the plug, not the cable.
Make sure that the charging cable is not mechanically damaged (kinked, jammed or run
over) and that the contact area does not come into contact with heat sources, dirt, or water.
Do not put your fingers into the connector.
Always conduct a visual inspection for signs of damage before charging. Pay particular
attention to dirt and moisture on the charging plug, cuts on the charging cable or chafing
on the insulation, and also ensure that the cable output from the Wallbox is securely
fastened.
(1) People who, as a result of the training, skills and experience and knowledge of the relevant standards
can assess the work and identify possible dangers.
EN
9
IMPORTANT
Never clean the Wallbox using a jet of water (hosepipe, pressure washer, etc.)!
Ensure that the Wallbox is not damaged by incorrect handling (housing cover, internal parts,
etc.).
If it is raining or snowing and the Wallbox is installed outdoors, do not open the terminal
panel cover.
Risk of breakage of the plastic housing!
- No countersunk screws may be used for mounting!
- Do not use force to tighten the fastening screws.
- The mounting surface must be completely flat (max. 1 mm difference between the
support or attachment points). Deflection of the housing must be avoided.
Instructions for trained personnel authorised to open the device:
Danger of damage. Electronic components may be destroyed if touched.
Before handling modules, perform an electrical discharge process by touching a metallic
earthed object.
A failure to follow the safety information may result in a danger of death, injury or damage to the
device! The device manufacturer cannot accept any liability for claims resulting from this!
10
This manual suits for next models
2
Table of contents
Other BMW Batteries Charger manuals
