BlueCom SETEL-D User guide
BCTS1047SETEL.SD.E1.doc, Rev.1.0
BlueCom Ltd.
SETEL-D
System Description
Selective Party Line Telephone Set
with integrated Decoder
Doc.-No. Revisison Date
BCTS1047 Rev. 0 Master Edition
3.9.2013
Great care has been taken to ensure that the information contained in this
handbook is accurate and complete. Should any errors or omissions be
discovered or should any user wish to make a suggestion for improving
this handbook, he is invited to send the relevant details to:
BlueCom Ltd.
Giessenstrasse 15
8953 Dietikon
SWITZERLAND
Telephone +41 44 748 48 18
Telefax +41 44 748 48 19
E-mail [email protected]
Internet http://www.bluecom.ch
© BlueCom Ltd.
All rights are reserved. Reproduction in whole or in part is prohibited
without the written consent of the copyright owner.
System Description SETEL-D
BCTS1047SETEL.SD.E1.doc, Rev. 0 BlueCom Ltd., 3.9.2013 3
Limited Warranty and Warranty Claims
BlueCom AG warrants each new product manufactured and sold by it to be free from defects
in material, workmanship and construction, except for batteries, fuses, or other material
normally consumed in operation which may be contained therein, for a period of one year after
shipment to the original purchaser (which period is referred to as the “warranty period”). This
warranty shall not apply if the product is used contrary to the instructions in its manual or is
otherwise subjected to misuse, abnormal operation, accident, or repairs or modifications that
have not been performed by BlueCom. BlueCom is not responsible for products which it does
not manufacture.
BlueCom’s obligation under this warranty is limited to in-factory servicing and repairing, at
BlueCom’s option, the product or the component thereof which is found to be defective. If in
BlueCom’s judgment the defective condition in a BlueCom product is for a cause listed above
for which BlueCom is not responsible, BlueCom will make the repairs or replacement of
components and charge its then current price, which buyer agrees to pay.
BlueCom shall not be responsible if the following procedure for warranty claims is not
followed. BlueCom shall be notified of the claim with full information as the claimed defect.
BlueCom products shall not be returned unless a return authorization number is issued by
BlueCom. BlueCom products must be returned with the description of the claim defect and
identification of the individual to be contacted if additional information is needed. BlueCom
products must be returned properly packed with transportation charge prepaid.
Except for the limited warranty stated above, BlueCom disclaims all warranties of any kind
with regard to BlueCom products or other materials provided by BlueCom, including without
limitation any implied warranty of merchantability or fitness for a particular purpose. BlueCom
shall have no liability or responsibility to the original customer or any other party with respect
to any liability, loss or damage caused directly or indirectly by any BlueCom product, material
or software sold or provided by BlueCom, BlueCom replacement parts or units, or service
provided by BlueCom, including but not limited to any interruption of service, excess charges
resulting from malfunctions of hardware or software, loss of business or anticipatory profits
resulting from the use or operation of the BlueCom product or software, whatsoever or
howsoever caused, and in no event shall BlueCom be liable for any direct, indirect, special or
consequential damages whether the claims are grounded in contract, tort (including
negligence), or strict liability.
Rights to Software
BlueCom retains ownership of the software supplied with this equipment and all copyrights for
the software. This software may be stored in the integrated circuits or in machine or human
readable form. BlueCom grants only a non-exclusive license to buyer to use the software
solely in connection with the normal and customary use of the equipment supplied to buyer
under this order. Buyer agrees not to read out the software from the integrated circuits and
disclose or make any use of such software other than the use allowed under this license.
System Description SETEL-D
BCTS1047SETEL.SD.E1.doc, Rev. 0 BlueCom Ltd., 3.9.2013 4
Contents Page
1 Introduction ............................................................................................................. 5
2 Mode of Operation .................................................................................................. 6
2.1 Mode 1, Standard Party Line .......................................................................... 6
2.2 Mode 2, Connection to a PABX ...................................................................... 7
2.3 Mode 3, 4W Remote Subscriber (MUTEL) ..................................................... 7
3 SETEL-D Layout and Keys ..................................................................................... 8
4 Hardware Block Diagram ...................................................................................... 10
5 Programming of SETEL-D .................................................................................... 11
5.1 Menu Structure ............................................................................................. 12
5.2 Programming of Function Keys .................................................................... 13
6 Installation ............................................................................................................. 14
6.1 Scope of Supply ........................................................................................... 14
6.2 Unpacking and Inspection ............................................................................ 14
6.3 Installation Recommendations ...................................................................... 14
6.4 DC-Power Requirements .............................................................................. 14
6.5 External Connections .................................................................................... 15
6.6 Connection Diagram ..................................................................................... 16
6.7 Jumper Settings: ........................................................................................... 17
6.8 Scope of Supply ............................................. Error! Bookmark not defined.
7 Technical Data ...................................................................................................... 19
System Description SETEL-D
BCTS1047SETEL.SD.E1.doc, Rev. 0 BlueCom Ltd., 3.9.2013 5
1 Introduction
The selective party line telephone set with integrated decoder SETEL-D is used in classical
party line networks and as a service telephone in digital SDH/PDH communication networks.
The SETEL-D is compatible with the former SETEL and existing ABB party line telephone
systems.
SETEL-D combines the functions of a 4-wire telephone set and a DTMF decoder. When used
together with the 4-way bridging amplifier (J3KA), a complete party line telephone system can
be constructed.
The programmed data is stored in an internal SD Memory card inside the SETEL-D. All
functions can be programmed with the aid of the dialling key pad and the built-in 20 character
by 2 line LC-Display.
The SETEL-D has three main operational modes:
Mode 1: Standard 4W party line telephone set with DTMF decoder
Mode 2: Connection to a 4W E&M PABX (not yet implemented)
Mode 3: 4W-telephone set without DTMF decoder (MUTEL Mode)
System Description SETEL-D
BCTS1047SETEL.SD.E1.doc, Rev. 0 BlueCom Ltd., 3.9.2013 6
2 Mode of Operation
The SETEL-D can be programmed for three different operating modes.
Mode 1: 4W Party Line Telephone Set with DTMF Decoder
Mode 2: Connection to PABX
Mode 3: 4W Remote Subscriber (MUTEL mode)
2.1 Mode 1, Standard Party Line
J3KA J3KA J3KA
Decoder
Interface
PABX
SETEL-D SETEL SETEL+
SETEL-D SETEL
Station A Station B Station C Station D
300
311
312
321 331
332
611 To Station E
In this application all SETEL-D telephone sets are sharing one analog 4W-voice channel. All
SETEL-D telephone sets have to share this voice channel and only one call can be made at
the same time. If two SETEL-D sets are communicating with each other and a third party
lifting the handset is automatically connected to the call and the new party can take part in the
conversation. (listen and talk).
E&M signals are not required for this application.
The SETEL-D is compatible with all ABB Party Line systems and old versions of SETEL.
System Description SETEL-D
BCTS1047SETEL.SD.E1.doc, Rev. 0 BlueCom Ltd., 3.9.2013 7
2.2 Mode 2, Connection to a PABX
In this mode the SETEL is acting like a PABX with one 4W E&M Interface. It can be
connected to any PABX, who is supporting continuos signalling protocol on the E&M Interface.
PABX
20xx
4W E&M
MUX MUX
SETEL
4W E&M
2011
3011 3012
3013
In this mode E&M signals have to be used in SETEL 3011. The call progress tones are
provided by the SETEL-D.
Digits received with pulse dialling will be converted to DTMF tones and will be resend.
2.3 Mode 3, 4W Remote Subscriber (MUTEL)
PABX
20xx
4W E&M
MUX MUX SETEL
4W E&M
2011
2012
In the SETEL 2012 the E&M signals have to be used. An incoming call is signalled by
activating the E signal on the 4W E&M Interface in the PABX. In this mode the DTMF decoder
inside the SETEL is not used. An outgoing call from the SETEL 2012 is signalled by activating
the M signal on the SETEL 2012. After that call progress tones will be provided by the PABX.
System Description SETEL-D
BCTS1047SETEL.SD.E1.doc, Rev. 0 BlueCom Ltd., 3.9.2013 8
3 SETEL-D Layout and Keys
1
2
3
4
5
6
7
13
14
15
16
17
18
19
8 20
9
10
11
12
21
22
23
24
1 2 3
4 5 6
7 8 9
0 #
SETEL
Function Keys
To program speed dial numbers and special functions
Hands Free
Loudspeaker Key Switch On and Off the hands free mode
Plus/Minus Keys
Volume adjustments of ring, voice on the loudspeaker and voice in the handset
Backward Key
to move backward in the input menus
Forward Key
to move forward in the input menus
System Description SETEL-D
BCTS1047SETEL.SD.E1.doc, Rev. 0 BlueCom Ltd., 3.9.2013 9
ESC Key
To escape from the menus without saving.
ENTER Key
To confirm and save inputs in the input menus
Clear-Key
To clear or delete values in the input menus
Further Keys
Redial Key
To redial last number dialed
Hook Switch and Telephone Directory
This key is also used to change between numbers, small and capitol letters for the text
entries.
When entering text the following letters will be displayed depending on the number of
times a key has been pressed. The key is used to switch between small and capitol
letters.
1x 2x 3x 4x 5x 6x 7x 8x 9x 10x 11x 12x
1 Space
1 € £ $ ¥ ¤
2 a/A b/B c/C 2 ä/Ä
3 d/D e/E f/F 3
4 g/G h/H i/I 4
5 j/J k/K l/L 5
6 m/M n/N o/O 6 ö/Ö
7 p/P q/Q r/R s/S 7
8 t/T u/U v/V 8 ü/Ü
9 w/W x/X y/Y z/Z
0 . , ? ! 0 + - : ; _
*
# # * & ( ) @ \ / < = > %
F Key 12
F Key 11
System Description SETEL-D
BCTS1047SETEL.SD.E1.doc, Rev. 0 BlueCom Ltd., 3.9.2013 10
4 Hardware Block Diagram
-48V
+-5V
3
200mA
CPU
Display 2x24 character
SETEL-D
X1
X2
X3
4
5
6
2
1
Wall Jack
RJ11
Keyboard
Wall Jack
RJ11
BL
RED
GRN
BLK
WH
bu
rd
gn
bk
wh
bu
ye
rd
gn
wh
bk
GRN
RED
BLK
WH
YL
BL
Line In
Line Out
Earpiece
Handset
1
3
4
2
1
4
2
3
Mic
USB
Interface
DTMF
Decoder
LED
Indicators Ring LED gn
Speaker LED gn
Loudspeaker
Handsfree Mic
ye
YL
M (a)
4
5
56R
R (b)
6
7
56R
E (a)
-5V
3
256R 4k7
E(b)
180R 56R
J1
J2
1
8
not used
not used
-48V
0V (+)
R (a)
M (b)
(a)
(b)
(a)
(b)
RAM
USB for
Firmware
upgrade
This manual suits for next models
1
Table of contents
Other BlueCom Telephone manuals
