Blizzard Lighting Lo-Pro CSI User manual
Blizzard Lighting, LLC
www.blizzardlighting.com
Waukesha, WI USA
Copyright (c) 2015
Page 2
Lo-Pro CSI™ - Rev. A (c) 2015 Blizzard Lighting, LLC
TABLE OF CONTENTS
Lo-Pro CSI™ 1
1. Getting Started 3
What’s In The Box? 3
Getting It Out Of The Box 3
Powering Up! 3
Getting A Hold Of Us 3
Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4
2. Meet The Lo-Pro CSI™ 5
Features 5
DMX Quick Reference 5
The Lo-Pro CSI™ Pin-up Picture 6
3. Setup 7
Fuse Replacement 7
Connecting A Bunch Of Stiletto’s 7
Data/DMX Cables 7
Cable Connectors 8
3-Pin??? 5-Pin??? Huh? 8
Take It To The Next Level: Setting up DMX Control 8
Fixture Linking (Master/Slave Mode) 9
Mounting/Rigging 9
4. Operating Adjustments 10
The Control Panel 10
Control Panel Menu Structure 11
DMX Channel Settings 11
View Fixture Info (Hours, Version#) 11
Dimmer Delay Settings 11
DMX, Auto & Sound Active Modes 11
Manual Settings 11
Troubleshooting 12
5. Appendix 13
A Quick DMX Lesson 13
Keeping Your Lo-Pro CSI™ As Good As New 14
Returns (Gasp!) 14
Shipping Issues 14
Tech Specs 15
Page 3
Lo-Pro CSI™ - Rev. A (c) 2015 Blizzard Lighting, LLC
1. GETTING STARTED
What’s In The Box?
• 1 x Lo-Pro CSI™
• An Ever-So-Handy Power Cord
• One really classy DMX cable
• This Lovely User Manual
Getting It Out Of The Box
Congratulations on your purchase of the amazing Lo-Pro CSI™. With a name like Lo-Pro
CSI™, it is denitely worth some investigation! Now that you’ve got your Lo-Pro CSI™
(or hopefully, CSI’s!)
, you should carefully unpack the box and check the contents to en-
sure that all parts are present and in good condition. If anything looks as if it has been
damaged in transit, notify the shipper immediately and keep the packing material for
inspection. Again, please save the carton and all packing materials. If a xture must be
returned to the factory, it is important that the xture be returned in the original factory
box and packing.
Powering Up!
All xtures must be powered directly o a switched circuit and cannot be run o a
rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch.
AC Voltage Switch - Not all xtures have a voltage select switch, so please verify that the
xture you receive is suitable for your local power supply. See the label on the xture or
refer to the xture’s specications chart for more information. A xture’s listed current
rating is its average current draw under normal conditions. Check the xture or device
carefully to make sure that if a voltage selection switch exists that it is set to the correct
line voltage you will use.
Warning! Verify that the voltage select switch on your unit matches the line
voltage applied. Damage to your xture may result if the line voltage applied
does not match the voltage indicated on the voltage selector switch. All xtures
must be connected to circuits with a suitable Ground (Earthing).
Getting A Hold Of Us
If something is wrong, please just visit our website at www.blizzardlighting.
com and open a support ticket. We’ll be happy to help, honest.
Blizzard Lighting
N16 W23390 Stoneridge Dr. Ste E
Waukesha, WI 53188 USA
www.blizzardlighting.com
414-395-8365
Disclaimer: The information and specications contained in this document are subject
to change without notice. Blizzard Lighting™ assumes no responsibility or liability for any
errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the
right to update the existing document or to create a new document to correct any errors
or omissions at any time. You can download the latest version of this document from
www.blizzardlighting.com.
Author: Date: Last Edited: Date:
J. Henry 2/17/2015 J. Thomas 4/9/2015
Page 4
Lo-Pro CSI™ - Rev. A (c) 2015 Blizzard Lighting, LLC
SAFETY INSTRUCTIONS
• Please keep this User Guide for future use. If you sell the unit to someone
else, be sure that they also receive this User Guide.
• ALWAYS make sure that you are connecting to the proper voltage, and that
the line voltage you are connecting to is not higher than that stated on the de-
cal or rear panel of the xture.
• This product is intended for indoor use only.
• To prevent risk of re or shock, do not expose xture to rain or moisture.
• Make sure there are no ammable materials close to the unit while operating.
• The unit must be installed in a location with adequate ventilation, at least
20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are
blocked.
• ALWAYS disconnect from the power source before servicing or replacing fuse
and be sure to replace with same fuse size and type.
• ALWAYS secure xture using a safety chain. NEVER carry the xture by its
head. Use its carrying handles.
• DO NOT operate at ambient temperatures higher than 104°F (40°C).
• In the event of a serious operating problem, stop using the unit immediately.
NEVER try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorized tech-
nical assistance center. Always use the same type spare parts.
• NEVER connect the device to a dimmer pack.
• Make sure the power cord is never crimped or damaged.
• Never disconnect the power cord by pulling or tugging on the cord.
• Avoid direct eye exposure to the light source while it is on.
Caution! There are no user serviceable parts inside the unit. Do not
open the housing or attempt any repairs yourself. In the unlikely event
your unit may require service, please open a support ticket at www.
blizzardlighting.com/tickets.
Page 5
Lo-Pro CSI™ - Rev. A (c) 2015 Blizzard Lighting, LLC
2. MEET THE LO-PRO CSI™
MAIN FEATURES
• 36x high output, 3-watt ~365nm UV LED
• Full on UV intensity + 2 unique pixel patterns
• Variable electronic strobe and dimmer
• Built-in auto programs via master/slave
• Built-in sound active programs
• Standalone, master/slave, auto, sound active modes
• Easy 1/2/3/4/5-channel DMX control
• 15° Beam angle
• Lightweight and Compact (It kept its New Years’ resolution!)
• 4-button LED control panel for easy programming
• Power outlet for xture linking
• Two-piece mounting yoke allows exibility in positioning
DMX Quick Reference (1/2/3/4/5-Channel Modes)
Channel 1.001 2.001 3.001 4.001 5.001
1Dimmer UV Intensity Dimmer Dimmer Dimmer
2-- UV Intensity UV Intensity Strobe Strobe
3-- -- UV Intensity UV Intensity UV Intensity
4-- -- -- UV Intensity UV Intensity
5-- -- -- -- Color Temp
Page 6
Lo-Pro CSI™ - Rev. A (c) 2015 Blizzard Lighting, LLC
Figure 1: The Lo-Pro CSI™ Pin-Up Picture
36x3w ~365nm UV LEDs
Figure 2: The Rear Connections
PowerCon™
Compatible In/Out
LED Display
Touring-
grade
compact
shell
Two-piece
mounting
yoke
4-button Control Panel
Safety Cable Attachment Holes
DMX 3-pin In/Out
Tightening
Knob
Page 7
Lo-Pro CSI™ - Rev. A (c) 2015 Blizzard Lighting, LLC
3. SETUP
Fuse Replacement
CAUTION! The Lo-Pro Flux™ utilizes a high-output switch-mode power
supply with an internal fuse. Under normal operating conditions, the fuse
should not require replacement. The fuse is eld replaceable, however it
is an advanced procedure suited to qualied individuals. Should your Lo-
Pro Flux™ fuse require replacement, please contact Blizzard Lighting for
instructions, or to return your unit for service.
Connecting A Bunch of Lo-Pro Flux™ Fixtures
You will need a serial data link to run light shows using a DMX-512
controller or to run shows on two or more xtures set to sync in master/
slave operating mode. The combined number of channels required by all
the xtures on a serial data link determines the number of xtures the
data link can support.
Fixtures on a serial data link must be daisy chained in one single line.
Also, connecting more than 32 xtures on one serial data link without the
use of a DMX optically-isolated splitter may result in deterioration of the
digital DMX signal. The maximum recommended cable-run distance is 500
meters (1640 ft). The maximum recommended number of xtures on a
serial data link is 32 xtures.
Data/DMX Cabling
To link xtures together you’ll need data cables. You should use data-
grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
For instance, Belden© 9841 meets the specications for EIA RS-485
applications. Standard microphone cables will “probably” be OK, but note
that they cannot transmit DMX data as reliably over long distances. In
any event, the cable should have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor & shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms
Page 8
Lo-Pro CSI™ - Rev. A (c) 2015 Blizzard Lighting, LLC
Cable Connectors
Cables must have a male XLR connector on one end and a female XLR
connector on the other end. (Duh!)
CAUTION: Do not allow contact between the common and the x-
ture’s chassis ground. Grounding the common can cause a ground
loop, and your xture may perform erratically. Test cables with an
ohm meter to verify correct polarity and to make sure the pins are not
grounded or shorted to the shield or each other.
3-Pin??? 5-Pin??? Huh?!?
If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
They are widely available over the internet and from specialty retailers If you’d like to build your own, the
chart below details a proper cable conversion:
Conductor 3-Pin Female
(Output)
5-Pin Male
(Input)
Ground/Shield Pin 1 Pin 1
DMX Data (-) Pin 2 Pin 2
DMX Data (+) Pin 3 Pin 3
Not Used. No Connection. No Connection.
Not Used. No Connection. No Connection.
Take It To The Next Level: Setting Up DMX Control
Step 1: Connect the male connector of the
DMX cable to the female connector (output)
on the controller.
Step 2: Connect the female connector of the
DMX cable to the rst xture’s male connec-
tor (input). Note: It doesn’t matter which
xture address is the rst one connected.
We recommend connecting the xtures in
terms of their proximity to the controller,
rather than connecting the lowest xture
number rst, and so on.
Step 3: Connect other xtures in the chain
from output to input as above. Place a DMX
terminator on the output of the nal xture
to ensure best communication.
Page 9
Lo-Pro CSI™ - Rev. A (c) 2015 Blizzard Lighting, LLC
Fixture Linking (Master/Slave Mode)
1. Connect the (male) 3 pin connector side of the
DMX cable to the output (female) 3 pin connector of
the rst xture.
2. Connect the end of the cable coming from the
rst xture which will have a (female) 3 pin connec-
tor to the input connector of the next xture con-
sisting of a (male) 3 pin connector. Then, proceed
to connect from the output as stated above to the
input of the following xture and so on.
A quick note: Often,
the setup for Master-
Slave and Standalone
operation requires that
the rst xture in the
chain be initialized for
this purpose via either
settings in the control
panel or DIP-switches.
Secondarily, the xtures
that follow may also re-
quire a slave setting.
Check the “Operating Adjustments” section in this manual for com-
plete instructions for this type of setup and conguration.
Mounting & Rigging
This xture may be mounted in any SAFE position provided there is
enough room for ventilation.
It is important never to obstruct the fan or vents pathway. Mount the
xture using a suitable “C” or “O” type clamp. The clamp should be
rated to hold at least 10x the xture’s weight to ensure structural sta-
bility. Do not mount to surfaces with unknown strength, and ensure
properly “rated” rigging is used when mounting xtures overhead.
Adjust the angle of the xture by loosening both knobs and tilting the
xture. After nding the desired position, retighten both knobs.
• When selecting installation location, take into consideration lamp
replacement access (if applicable) and routine maintenance.
• Safety cables MUST ALWAYS be used.
• Never mount in places where the xture will be exposed to rain,
high humidity, extreme temperature changes or restricted ventilation.
Page 10
Lo-Pro CSI™ - Rev. A (c) 2015 Blizzard Lighting, LLC
4. OPERATING ADJUSTMENTS
The Control Panel
All the goodies and dierent modes possible with the Lo-Pro CSI™ are
accessed by using the control panel on the front of the xture. There
are 4 control buttons below the LED display which allow you to navi-
gate through the various control panel menus.
Button Function
<MENU>
<UP>
<DOWN>
<ENTER>
Used to access the menu or to return to a previous menu option.
Scrolls through menu options in ascending order.
Scrolls through menu options in descending order.
Used to select and store the current menu or option within a menu.
Access control panel functions using the four panel buttons located
directly underneath the LED Display.
The Control Panel LED Display shows the menu items you select from
the menu map on page #11. When a menu function is selected, the
display will show immediately the rst available option for the selected
menu function. To select a menu item, press <ENTER>.
Use the <UP> and <DOWN> buttons to navigate the menu map
and menu options. Press the <ENTER> button to access the menu
function currently displayed or to enable a menu option. To return to
the previous option or menu without changing the value, press the
<MENU> button.
Table of contents
Other Blizzard Lighting Lighting Equipment manuals
Blizzard Lighting
Blizzard Lighting HotStik 5 COB Mini User manual
Blizzard Lighting
Blizzard Lighting the puck User manual
Blizzard Lighting
Blizzard Lighting Flurry TRI User manual
Blizzard Lighting
Blizzard Lighting Stiletto Z7 User manual
Blizzard Lighting
Blizzard Lighting Tour QT Skywire User manual
Blizzard Lighting
Blizzard Lighting HUSH PAR Theatrik User manual
Blizzard Lighting
Blizzard Lighting G-Max 150 User manual
Blizzard Lighting
Blizzard Lighting ICE 30 User manual
Blizzard Lighting
Blizzard Lighting HUSH PAR Infiniwhite 500 User manual
Blizzard Lighting
Blizzard Lighting ToughPar V12 User manual
Blizzard Lighting
Blizzard Lighting Torrent 90 Beam User manual
Blizzard Lighting
Blizzard Lighting Puck CSI Xtreme User manual
Blizzard Lighting
Blizzard Lighting KAYO.MORPH User manual
Blizzard Lighting
Blizzard Lighting Lo-Pro Flux User manual
Blizzard Lighting
Blizzard Lighting mikrokassette User manual
Blizzard Lighting
Blizzard Lighting Kontrol 5 User manual
Blizzard Lighting
Blizzard Lighting the puck pro zoom User manual
Blizzard Lighting
Blizzard Lighting Torrent 90 Beam User manual
Blizzard Lighting
Blizzard Lighting the puck User manual
Blizzard Lighting
Blizzard Lighting Node:b RGBAL User manual
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
