BLINDSTER N300710-Q User manual

Roller Shade

INSTALLATION INSTRUCTIONS

Email: [email protected]

Call us: (888) 256-8672

Mon - Fri 8am - 7pm (CT)

N300710-Q

1. SCREWS NEEDED FOR INSTALLING

RECOMMENDED TOOLS

HARDWARE INCLUDED

Roller Tube/No Fascia

• Screw gun / Drill

• Tape Measure

• Screwdriver

• Level

• Pencil

With Fascia

Hardware Drawing Usage

1 1/4" Hexagon screw To install shade brackets

2" Flat head screw To install safety tension device for continuous cordloop

5/8” Flat head screw To install magnet catch

2. HARDWARE FOR REGULAR ROLLER SHADE (NO RACEWAY)

Hardware Drawing Usage

Shade bracket To install shade (on control side)

Shade bracket To install shade (on End Plug side)

Bracket cover Shade bracket cover (Pre-installed on the shade bracket)

Page 2

REGULAR SHADE (NO RACEWAY) INSTALLATION AND REMOVAL

3. HARDWARE FOR ROLLER SHADE WITH RACEWAY SYSTEM*

RACEWAY SYSTEM USED WITH FASCIA IS ORDERED

4. OTHER HARDWARE

Hardware Drawing Usage

Mounting bracket To install raceway (for outside mount)

Shade bracket To install raceway (for inside mount)

Raceway bracket clip To install shade bracket into raceway (for inside mount,

pre-installed on the shade bracket)

Valance bracket To install fascia / valance (mounted on raceway)

Valance clip To install fascia / valance (placed on fascia/valance)

Curved Fascia end cap For curved fascia

Hardware Drawing Usage

Handle For Cordless shades

Magnet Catch Optional (For magnetic hold down)

When installing the shade bracket, the distance from the bracket’s front mounting hole to the front edge of the window

frame should be at least 3/4". Make sure both shade brackets line up with each other horizontally.

Each shade bracket will require two 1 1/4" hexagon screws for the installation.

For Inside Mount installation, first fit the bracket cover over the shade bracket, and then screw brackets into wall.

INSTALLATION OF SHADE BRACKETS

N300710-Q

Page 3

1. First, insert the control side into the tongue of the bracket for the control side.

2. Second, press the end plug and insert the end plug into the hole of bracket of the other side.

3. Third, slide the lock pin in the shade bracket downward into the end plug to prevent the shade from falling.

4. Finally remove the paper band from the shade.

1. Use a tool to push the lock pin on end plug bracket upward.

2. Use tool to draw back the end plug from bracket.

3. Finally remove shade from mounting bracket. As shown in drawing.

Shade Installation Tips: After shade is installed into shade brackets, use a Level to check if the fabrics roll is horizontal;

if not, please adjust the position of shade brackets to keep the fabrics roll level.

Inside-Top

Mount

Inside-Side

Mount

Outside MountInside-Back

Mount

INSTALLATION OF THE SHADE

REMOVAL OF THE SHADE

Align control

side of the shade

with the tongue

of the bracket for

the control side.

Slide the lock pin in

the shade bracket

downward into the

end plug to prevent

the shade from falling.

1 2

The shade needs to be level.

The gap on end plug side

needs to be about3/16".

N300710-Q

Page 4

Attach the shade brackets and raceway bracket clips into the two ends of the raceway. Make sure the raceway

bracket clip’s bolt locks into the raceway’s dedicated hole. Install the raceway into the window opening.

We recommend securing the screws into the middle holes of the raceway first. This would allow you to adjust the

raceway left or right if required. Once the correct position has been located, secure the screws for the holes. Take

care that the distance between the 1st screw and the window edge is at least 3/4".

INSTALLATION OF MOUNTING / SHADE BRACKETS

INSIDE MOUNT

When installing the mounting brackets, the distance from the bracket’s front mounting hole to the front edge of the

window frame should be at least 3/4". Make sure all brackets line up with each other horizontally. Each bracket will

require two 1 1/4" hexagon screws for the installation.

Brackets position:

OUTSIDE MOUNT

For inside mount, the shade installation is same as

regular shade. Refer to the previous regular shade

installation instructions for details. For outside

mount, before installing the shade into the

mounting brackets, please locate the lock pin in

the shade bracket on the end plug side. Slide the

pin downward into the end plug to prevent the

shade from falling.

Insert the back edge of the raceway into the back

plastic part of the bracket, and then turn the

raceway upwards so that the front rib of the

raceway snaps into the bracket.

INSTALLATION OF SHADE

RACEWAY SYSTEM INSTALLATION AND REMOVAL

N300710-Q

Page 5

INSTALLATION

CONTINUOUS CORD LOOP OPERATION

B. MAGNETIC HOLD DOWN

For inside mount, the shade removal is same as

regular shade. Refer to the previous regular shade

removal instructions for details.

For outside mount, use a tool to push back the front

or back plastic part of the brackets, and then turn

the back side of the raceway downward so that it

detaches from the bracket. Finally remove the

raceway by pulling downward from the brackets.

Use 5/8" flat head screw to secure the magnet catch at the below location.

Make sure the magnet catch aligns with the pre-installed magnet on

shade bottom rail.

To lower the

shade,

pull downward

on the side of the

bead chain that is

closest to the

shade fabric.

To raise the

shade,

pull downward on

the side of the

bead chain that is

farthest away

from the shade

fabric.

For Continuous Cordloop Shades

Use two 2" flat head screws to install the safety device.

The bead chain should be fully extended upon installation of the device.

REMOVAL OF SHADE

INSTALL SAFETY TENSION DEVICE

N300710-Q

9/16"

11/16"

Side edge of

the shade

Bottom edge of

the shade

CONTINUOUS CORDLOOP

Page 6

3 4 5

1. Turn over hem bar and you can see a label attached at the center of the hem bar.

2. Align the center of the bottom of the handle with the label.

3. Hook the handle to the hem bar from top to bottom.

4. Press the handle from top to bottom to make the top of the handle clip into the hem bar.

5. Tear off the label from hem bar.

Use straight screwdriver to pry the bottom

of Handle from hem bar and then the

handle can be removed.

N300710-Q

HANDLE INSTALLATION AND REMOVAL

ATTACH HANDLE TO HEM BAR

The center of handle should

be aligned with the label.

Label

REMOVE HANDLE FROM HEM BAR

CORDLESS OPERATION

The tension in our cordless roller shades can

be adjusted to provide optimal light control

and to ensure easy and dependable

operation on a variety of window types and

sizes. If a cordless shade begins to slide

down on its own or it fails to roll up,

the issue can be easily fixed by turning the

adjustment dial towards “+” to increase the

tension. Conversely, if the cordless shade

cannot stop at the desired height and tends

to roll up by itself, the tension can be

decreased by turning the adjustment dial

towards the “-”.

The shade must be installed on the

brackets when adjusting.

Pull the handle

downwards or

upwards and

the shade will

be lowered or

raised.

Place the U-shape

channel of pole under

the handle and push up

to lift the shade.

Use the “hook”

portion to hook

the handle to

lower the shade.

INSTALLATION

CORDLESS

Page 7

To avoid motors waking and running during shipping process, motors are set as sleeping mode before shipped out.

Please short press P1 once to activate motors before operating. After short pressing P1, the motors will wake, enabling it

to run in a direction.

After installing the shade and raceway, the brackets for

the fascia come next. Align the fascia bracket with the

raceway first and then push the bracket onto the

raceway. The top groove of the fascia bracket should

hook onto the top of the raceway while the bracket's

bottom groove clips into the bottom rib of the raceway,

as shown below.

This drawing shows the fascia brackets installed in an

ideal position. They are placed far enough apart so that

the space is divided evenly.

Insert the fascia clip into the dedicated groove on the aluminum strip, paying special attention to the direction of the fascia

clip. The fascia clip should face up and should align with the fascia bracket as pictured.

N300710-Q

AUTOMATE MOTORIZATION

FASCIA BRACKET INSTALLATION

FASCIA CLIP INSTALLATION

There are total 15 channels (channel# 1~15) available. The shade will be

default pre-program in channel 1 unless specified at the factory before

shipping. The default setting from the factory for channel 0 is to operate all

shades at once.

15-CHANNEL REMOTE:

Channel

select

Stop

Down

Top

INSTALLATION

FASCIA

For Fascia:

The direction of

this valance clip

is facing upwards.

ATTACH FASCIA END CAP TO FASCIA

ATTACH FASCIA TO RACEWAY

Slide the clips to a position on the fascia so that they are each aligned with a bracket on the raceway, and then push the

clips into the bracket.

Page 8

N300710-Q

Note: please skip this

step if there is no returns

For Fascia:

FASCIA REMOVAL

• First, remove fascia together with clips and detach

them from the brackets.

• Take down shade from mounting brackets before

removing brackets from raceway.

• Turn the brackets 90 degree, and then take off

brackets from raceway, as shown below.

Note: The installation & removal for all fascias are the same.

SPECIFICATION

Page 9

N300710-Q

NO. ITEM Specification

1MRS-32A: AC Power 100-240V, 50 / 60Hz

Power Source

2 4.2V~3.4V (Single cell)

Battery operating

voltage range

32415~2459MHzRadio type

42.4G RFFrequency band(s)

5Brush DC motorMotor type

6< 3 hoursCharging Time

70°C/32°F ~ 40°C/104°FCharging Temperature

80°C/32°F ~ 40°C/104°FOperating Temperature

90% ~ 90% (Non-condensing)Relative Humidity

10 50dBAAve. Sound Level @1m

INSTALLATION

NORMAN SMART MOTORIZED SHADE

Page 10

N300710-Q

SAFETY PRECAUTIONS

• WARNING! Important safety instruction: It is critical for

your safety and the safety of those around you to

follow these instructions. Please save these

instructions for future use.

• WARNING! The motor/shade must be disconnected

from its power source during cleaning, maintenance

and when replacing parts.

• The products may contain Lithium-ion batteries; the

battery contains flammable materials such as

organic solvents. Please read the Important Safety

Precautions before using the product.

• Please recharge the batteries every 3-6 months to

ensure optimal performance of batteries.

• Product operation is intended for temperatures

between 0°C/32°F~40°C/104°F.

• Please note that the limited warranty will be voided if

the product is modified, dismantled or used in any

manner other than its intended purpose.

• The accessories, including Charging Wand, Adapter,

and Remote are designed to be used with our

Motorized Shades. Do NOT use them for any other

purpose.

• Please make sure the shade route is clear when

operating to avoid danger or damage.

• In order to improve the user experience and

functionality, the firmware and software of this

product will automatically update from time to time.

• WARNING! For the purposes of recharging the battery,

only use the detachable supply unit provided with this

appliance. ____ Detachable supply unit

(UHVUU3036-240015SA)

• Do NOT disassemble the products or any of their

components. They do not contain serviceable parts.

Servicing of these products should be referred to

qualified personnel.

• This appliance contains batteries that are only

replaceable by skilled personnel, trained authorized

retailer or electrician.

• Do NOT operate the product with wet hands to avoid

risk of electrical shock. The product needs to be

powered off and disconnected from its power source

during cleaning, maintenance and/or replacing parts.

Thank you for your purchase. Please review the instructions carefully before using the product, and save these

instructions for future consultation.

• The appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety. Children should be

supervised to ensure that they do not play with the

appliance.

• The appliance is only to be used with the power

supply unit provided with the appliance.

• If the supply cord is damaged, it must be replaced by

the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard.

• WARNING: Important safety instructions. It is

important for the safety of persons to follow these

instructions. Save these instructions.

• WARNING: Important safety instructions. Follow all

instructions, since incorrect installation can lead to

severe injury.

- Before installing the drive, remove any unnecessary

cords or components and disable any equipment not

needed for powered operation; -the characteristics of

the driven part must be compatible with the rated

load and rated operating time.

- The mass and the dimension of the driven part shall

be compatible with the rated torque and rated

operating time;

- Fixed controls have to be clearly visible after

installation.

• This appliance contains batteries that are only

replaceable by skilled persons.

• Do NOT operate when maintenance, such as window

cleaning, is being carried out in the vicinity.

• IMPORTANT: Please reserve space for connecting the

Power Charger while installing the shade, please refer

to “Installation” Section for more information.

• Do not allow children to play with fixed controls. Keep

remote controls away from children.

• Frequently examine the installation for imbalance

and signs of wear or damage to cables springs and

fixings. Do not use if repair or adjustment is necessary.

• LpA ≤ 70 dB (A).

Table of contents

Popular Window Blind manuals by other brands

Jysk

Jysk ROGEN manual

SOMFY

SOMFY 1241752 instructions

Rollos

Rollos S-Nanorollo V2 Assembly and operating instruction

Teptron

Teptron Move user manual

Renson

Renson Outdoor Loggia Manual Installation

Project Source

Project Source CDLF2342W quick start guide

Domondo

Domondo PureNight Mounting guide

rollease acmeda

rollease acmeda Easy Spring Air Assembly and installation manual

IKEA

IKEA KADRILJ manual

Hallis Hudson

Hallis Hudson Rolls Super glide instructions

Benthin

Benthin P1614 quick start guide

MV LINE

MV LINE CLARA 015 Installing instructions

Current

Current E-WAND Installation manual and user's guide

weinor

weinor VertiTex ZipR Maintenance Instructions and Directions for use for the end user

Roto

Roto ZAR M R4/R7 Mounting instructions

SOMFY

SOMFY Movelite WT Series instructions

Acmeda

Acmeda RF400 Series instructions

Motura

Motura Pli_353/3 manual