Blastrac 1-8DPS30 220V-SP User manual
Operating Instructions
1-8DPS30 220V-SP
MAN-1-8DPS30 220V-SP-EN
WM-Blastrac 1-8DPS30 220V-SP Manual
Rev.0
WM-Blastrac 1-8DPS30 220V-SP Manual
Printed on 9/10/13
Page 1 of 103
Technical data
Safety instructions
General
Transport
Initial operation
Operation
Maintenance
Electrical systems
Fault diagnosis
Spare parts
Design and specifications are subject to
change without notice - May 2006
Blastrac BV
Utrechthaven 12
3433 PN Nieuwegein
THE NETHERLANDS
T +31(0)30 - 601 88 66
F +31(0)30 - 601 83 33
I www.blastrac.com
Nieuwegein
WM-Blastrac 1-8DPS30 220V-SP Manual
Rev.0
WM-Blastrac 1-8DPS30 220V-SP Manual
Printed on 9/10/13
Page 2 of 103
WM-Blastrac 1-8DPS30 220V-SP Manual
Rev.0
WM-Blastrac 1-8DPS30 220V-SP Manual
Printed on 9/10/13
Page 3 of 103
1-8DPS30 220V-SP Operating Instructions
Technical data
Contents Chapter 1
1.1 Rating
1.2 Unit specifications
1.3 Operative range and correct usage
1.4 Stand-by power supply (generator)
1.5 Machine type designation
1.6 Advice for operators of blast cleaning machines
1
WM-Blastrac 1-8DPS30 220V-SP Manual
Rev.0
WM-Blastrac 1-8DPS30 220V-SP Manual
Printed on 9/10/13
Page 4 of 103
Operating Instructions 1-8DPS30 220V-SP
Technical data
1.1 Rating
Unit / designation : Blastrac blast cleaning machine
Machine type : 1-8DPS30 220V-SP
Manufacturer : Blastrac
Utrechthaven 12
NL-3433PN Nieuwegein
THE NETHERLANDS
1.2 Unit specifications
Dimensions:
1-8DPS30
220V-SP
Length 1400 mm
Width 400 mm
Height 1000 mm
Weight 125 kg
Connected loads (electrical system):
The indicated input current values correspond to the nominal current
values of the motors working under full load. These values are not
achieved under normal operating conditions.
1-8DPS-30 220V-SP Power
consumption Input
current
Blast wheel drive 3,0
kW max.13 A
Drive motor 0,18
kW max. 1,5 A
Electrical connection required : 220V, 60 Hz, 16 A, CEE plug
Rated speed Enclosure
Drive of blast wheel 2830 min-1 IP 54
Drive of drive motor 3000 min-1 IP 44
2
WM-Blastrac 1-8DPS30 220V-SP Manual
Rev.0
WM-Blastrac 1-8DPS30 220V-SP Manual
Printed on 9/10/13
Page 5 of 103
1-8DPS30 220V-SP Operating Instructions
Technical data
Blast wheel size : 165 mm Ø
Working width : 200 mm
Drive speed : 0,5 - 23 m/min
Blast cleaning output 3,0 kW : up to 50 m²/h on concrete
Dust hose connection : 75 mm Ø
Recommended abrasive : Media No. 2 - No. 4
Abrasive consumption : 100 g/m²
Recommended filter unit : contact Blastrac for a
suitable filter unit
1.3 Operative range and correct usage
The 1-8DPS30 220V-SP is exclusively designed to
clean dry, frost-free horizontal surfaces. The
machine may not be used for other purposes. The
manufacturer will not be liable for damage resulting
from such incorrect usage. In these cases the user
assumes all risks.
1.4 Stand-by power supply (generator)
If the 1-8DPS30 220V-SP blast cleaning machine is
operated using a generator, this generator must be
operated in accordance with the current VDE
directives (this applies to the protective earth
conductor in particular) in order to ensure that all
safety devices are functioning and to eliminate
possible damage to electrical components.
3
WM-Blastrac 1-8DPS30 220V-SP Manual
Rev.0
WM-Blastrac 1-8DPS30 220V-SP Manual
Printed on 9/10/13
Page 6 of 103
Operating Instructions 1-8DPS30 220V-SP
Technical data
1.5 Machine type designation
number of blast wheel
s
blast cleaning widt
h
Product code, 3 kW,
220V, single phas
e
1- 8 DPS-30 220V-SP
1.6 Advise for operators of blast cleaning machine
In accordance with the accident prevention regulations for blast
cleaning work (VBG 48) the operator must provide operating
instructions for blast cleaning work in a form and language that is
understandable.
The blast cleaning machine Operating Instructions are only part of
these operating instructions. Please consult the current accident
prevention regulations for the precise content.
Before operation, please make inquiries after the surfaces to be
treated in view of health hazard or carcinogenic materials. When a
different filter material is needed for the filter unit, please contact our
local Blastrac customer service department.
4
WM-Blastrac 1-8DPS30 220V-SP Manual
Rev.0
WM-Blastrac 1-8DPS30 220V-SP Manual
Printed on 9/10/13
Page 7 of 103
1-8DPS30 220V-SP Operating Instructions
Safety instructions
Contents Chapter 2
2.0 Warnings and symbols
2.1 Organisational measures
2.2 Personnel selection and qualification
2.3 Safety precautions applicable to different operating conditions
2.4 Special work within the scope of use of the equipment and
maintenance activities as well as repairs during operation
2.5 Definition of the Safety off position
2.6 Particular dangerous aspects of the equipment
2.7 Electrical engineering regulations
1
WM-Blastrac 1-8DPS30 220V-SP Manual
Rev.0
WM-Blastrac 1-8DPS30 220V-SP Manual
Printed on 9/10/13
Page 8 of 103
Operating Instructions 1-8DPS30 220V-SP
Safety instructions
2.0 Warnings and symbols
The following denominations and symbols are used in the Operating
Instructions to highlight areas of particular importance:
Symbol of operational safety.
In these Operating Instructions this symbol will be
shown next to all safety precautions that are to be
taken in order to ensure prevention to life and injury.
Follow these instructions and take special care in
these circumstances. In addition to these
instructions, the general safety precautions and
accident prevention guidelines are also to be
followed.
Particular details regarding the economical use of
the equipment.
Information, instructions and restrictions with regard
to possible risks to persons or to extensive material
damages.
2
WM-Blastrac 1-8DPS30 220V-SP Manual
Rev.0
WM-Blastrac 1-8DPS30 220V-SP Manual
Printed on 9/10/13
Page 9 of 103
1-8DPS30 220V-SP Operating Instructions
Safety instructions
Warning against dangerous voltages.
Indications relating to protective devices in electrical
appliances.
Indications where consultation with the
manufacturer is required.
Instructions relating to periodical checks.
Reference to important instructions contained in the
Operating Instructions.
2.1 Organisational measures
The Operating Instructions are to be kept near the location
where the machine is located and must be within reach at all
times!
In addition to the Operating Instructions general and legal regulations
regarding accident prevention and environmental protection must be
complied with and indicated!
Such duties may for example relate to the handling of hazardous
substances or to the provision and wearing of personal protection
equipment as well as compliance with traffic regulations.
3
WM-Blastrac 1-8DPS30 220V-SP Manual
Rev.0
WM-Blastrac 1-8DPS30 220V-SP Manual
Printed on 9/10/13
Page 10 of 103
Other manuals for 1-8DPS30 220V-SP
1
Table of contents
Other Blastrac Shot Blasting Machine manuals
