Move your NETTI
Plug your NETTI to an outlet where you want to extend your router’s Wi-Fi connection.Your NETTI will
connect to your router automatically. If the Signal Strength LED reads at least 3 bars, you can use your
NETTI at this location.
Follow the instructions
on the screen. The
app will automatically
discover your NETTI
and guide you to setup
its Wi-Fi connection
with your router.
Method Two: Web Browser Setup
1
2
Plug your NETTI into a power outlet
Plug your NETTI into a power outlet near your Wi-Fi router. If the signal
strength LEDs are flashing (first time setup) or unlit (no signal), proceed
with setup.
NOTE: Please refer to the diagram in Step 1 of Method One.
Configure your NETTI with the web-based user
interface
Open a web browser. Enter the default IP
address http://192.168.1.254. Enter the default
username (admin) and password (admin).
Follow the instructions on the screen to set up
the SSID and password of your Wi-Fi router. If
the setup is successful, your NETTI will repeat
the Wi-Fi connection of your Wi-Fi router.
Move your NETTI
Plug your NETTI to an outlet where you want to extend your router’s Wi-Fi connection.Your
NETTI will connect to your router automatically. If the Signal Strength LED reads at least 3
bars, you can use your NETTI at this location.
Connect your NETTI to a computer
Connect your NETTI to your computer with the Ethernet cable. Alternatively,
you can connect your NETTI to your computer wirelessly. Enable Wi-Fi
connection on your computer. Select the SSID NETTI_xxxx and click Connect.
3
4
4
5
5
Your Wi-Fi connection is extended
Your Wi-Fi signal now covers a wider area than before.
Your Wi-Fi connection is extended
You now have Wi-Fi connection in a wider area than before.
Make sure that the Wi-Fi
connection is enabled on
your mobile device, then
launch the NETTI app.
Navigate through the
app tour by swiping left.
Method Three: App Setup
1 Install the NETTI app
Download and install the NETTI app from either the Google Play Store or
the iOS App Store.
2
3
Plug your NETTI into a power outlet
Plug your NETTI into a power outlet near yourWi-Fi router. If the signal strength
LEDs are flashing (first time setup) or unlit (no signal), proceed with setup.
NOTE: Please refer to the diagram in Step 1 of Method One.
Configure your NETTI with the NETTI app
When you get to the
Add NETTI selection
page, select Setup
Extender Mode using
your app.
or
User Name: admin
Password:
Remember Password
Copyright © 2 014 Blackloud, Inc. All Rights Re served.
Frequently Asked Questions
Q: My computer cannot connect to my NETTI.
A: Please make sure that your computer is properly connected to your NETTI via the Ethernet cable or that your computer’s Wi-Fi
connection is enabled.
Q: The NETTI app cannot find my NETTI.
A: Please make sure that Wi-Fi is enabled on your mobile device.
Q: I have setup my NETTI’sWi-Fi connection to my router, but the Wi-Fi signal is poor from my NETTI.
A: Your NETTI may be too far away from your router.Try to move and re-plug your NETTI to a power outlet closer to the router such that
the Signal Strength LED reads at least 3 bars.
For More Information
For more information regarding the use of your NETTI Wi-Fi extender, please check the user manual available on the company website:
www.blackloud.com
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by BLACKLOUD, Inc.
is under license. Other trademarks and trade names are those of their respective owners.
Android is a trademark of Google Inc.
IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.
