Black Box SW1035A User manual

SINGLE MODE

FIBER OPTIC A/B SWITCH

(LATCHING)

SEPTEMBER 2008

Model# SW1035A

Model# SW1036A

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S.: 877-877-BBOX (outside U.S. call 724-746-5500)

FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or

fax 724-746-0746

Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

Page 2

Single Mode Fiber Optic A/B Switch (latching)

FEDERAL COMMUNICATIONS COMMISSION

AND

INDUSTRY CANADA

RADIO FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio-frequency energy, and

if not installed and used properly, that is, in strict accordance with the

manufacturer’s instructions, may cause interference to radio communication.

It has been tested and found to comply with the limits for a Class A

computing device in accordance with the specifications in Subpart B of Part

15 of FCC rules, which are designed to provide reasonable protection

against such interference when the equipment is operated in a commercial

environment. Operation of this equipment in a residential area is likely to

cause interference, in which case the user at his own expense will be

required to take whatever measures may be necessary to correct the

interference.

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise

emission from digital apparatus set out in the Radio Interference Regulation

of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques

dépassant les limites applicables aux appareils numériques de la classe A

prescrites dans le Règlement sur le brouillage radioélectrique publié par le

Industrie Canada.

FCC STATEMENT

Page 3

Single Mode Fiber Optic A/B Switch (latching)

Contents

Chapter Page

1. Specifications …………………………………... 4

2. Introduction …………………………………. 5

3. Installation …………………………………….. 6

4. Troubleshooting ……………………………….. 6

CONTENTS

Page 4

Single Mode Fiber Optic A/B Switch (latching)

Specifications

Connectors

(3 pairs) ST connectors, (1) 3.5-mm power input

(SW1035A)

(3 pairs) SC connectors, (1) 3.5-mm power input

(SW1036A)

Data Rates

Transparent to signal rates, wavelengths, & formats

Switching Speed

less than 10 ms typical

Sensitivity

1310 / 1550 nanometers

Optical Loss

less than 2.0 dB typical

Compatibility

8 to 10um Single mode fiber

Crosstalk

less than -55 dB typical per FOTP-42

Approvals

UL, CE, and PSE (power supply)

Operating Temperature

14 to 149ºF (-10 to +65ºC)

Relative Humidity Tolerance

10 to 95%, non-condensing

Chapter 1: Specifications

Page 5

Single Mode Fiber Optic A/B Switch (latching)

Mean Time Between Failures

100,000 hours or 10,000,000 cycles

Power

100-240 VAC 50/60 Hz wall-mount PSU, 12 VDC out

Size

2.5”H x 8”W x 6.3”D (6.4 x 20.3 x 16 cm)

Weight

4 lb. (1.8 kg)

Introduction

The Single Mode latching Fiber Optic A/B Switch is a

full-duplex, optical 2 port switch. It can be used to connect

one workstation to two different networks (one at a time)

or to other remote devices. A front panel rotary style knob

allows the user to select which of two ports (A or B) is

connected to the COMMON (C) port on the switch. The

switch operates using a unique all-optical micro-mirror

movement. When you turn the rotary knob on the front of

the switch to select a network, the internal micro-mirror

movement redirects the optical beam from one network

port to another network port by rotating a miniature mirror.

This technique eliminates the need to convert optical

signals to electronic signals for switching and is therefore

transparent to data rates and protocols.

This switch is perfectly suited for applications where a

selected connection must be maintained in the event of a

power failure. You should use a non-latching fiber optic

switch for applications requiring a switch that falls back to

pre-determined connection during the loss of AC power

(please call us). These switches use power only for

switching the selected connection. No power is required to

pass data through the switches.

Chapter 2: Introduction

Page 6

Single Mode Fiber Optic A/B Switch (latching)

Installation

Place the switch in a convenient stable location and

connect the power supply unit to a reliable source of AC

power that meets the requirements shown in the

Specifications section of this manual. Then change the

front panel rotary knob to switch between the different

connection states to insure that the latching fiber optic

switch modules are in a known position before

connecting the switch to your fiber optic devices.

Connect the two fiber leads from the device to be shared

to the common switch port labeled C. Connect the

networks or other devices to the user selectable output

ports labeled A and B.

Your installation of this switch is now complete.

Troubleshooting

If the Fiber Optic A/B Switch fails to operate, check the

following before calling for technical support.

1. Ensure that the power supply connected to a power

source and to the switch.

2. Check the fiber optic connectors for proper

connections to the correct ports of the switch.

3. Operate the switch knob to verify that it’s tightly

secured to the switch shaft and does not spin loosely.

4. Verify the integrity of the fiber optic leads by

replacing a suspect lead with a spare.

Chapter 3: Installation

Chapter 4: Troubleshooting

Page 7

Single Mode Fiber Optic A/B Switch (latching)

Notes:

1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746

This manual suits for next models

Table of contents

Other Black Box Switch manuals

Black Box

Black Box SW459A-ST User manual

Black Box

Black Box LGB1126A-R2 User manual

Black Box

Black Box KV7004A User manual

Black Box

Black Box 12-Port 1000BASE-TX L2 Managed PoE Switch User manual

Black Box

Black Box SW930A-R2 User manual

Black Box

Black Box JPM370A-R2 User manual

Black Box

Black Box PSE518SA User manual

Black Box

Black Box ServSwitch KV752AE User manual

Black Box

Black Box KVS4-1002V User manual

Black Box

Black Box LPDG705A User manual

Black Box

Black Box ServSwitch ACU5501A-R4 User manual

Black Box

Black Box KV9508A User manual

Black Box

Black Box LB8405A-R2 User manual

Black Box

Black Box SW1023A User manual

Black Box

Black Box PI750A User manual

Black Box

Black Box LB9024A User manual

Black Box

Black Box IC1027A User manual

Black Box

Black Box SW625A-R3 User manual

Black Box

Black Box SWL930A-R2 User manual

Black Box

Black Box AVSW-HDMI8X8-X User manual

Black Box

Black Box SW1046A User manual

Black Box

Black Box ServSelect III KV22016A User manual

Black Box

Black Box LH8000A-M User manual

Black Box

Black Box LGB1110A User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual